aegis 4000rt PLUS Installation and Programming Manual REV. 051512 PACH & COMPANY www.pach-co.com 946 Calle Amanecer, Ste.
TABLE OF CONTENTS LIMITATION OF LIABILITY CHAPTER 1. GETTING STARTED ............................................................................................................................... 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Introduction ................................................................................................................................................ 1 System Descriptions ........................................................................................................
How to Use Speed Dialing ................................................................................................................................24 CHAPTER 5. TROUBLE SHOOTING GUIDES ........................................................................................................... 25 Audio Problems ............................................................................................................................................... 25 Communication Problems ........................
LIMITATIONS OF LIABILITY This manual is subject to change without notice. Pach and Company is not liable for any errors that might occur from use of this document, nor is any commitment to update the information herein implied. Pach and Company does not assume any liability for any damages, which may arise in installation or use of the AeGIS 400RTP Series. Pach and Company does not assume liability for any incompatibility between the AeGIS 400RTP Series and users devices.
CHAPTER 1. GETTING STARTED 1.1 Introduction Pach & Company thanks and congratulates you on the purchase of your AeGIS 400RTP Series Telephone Access Control System. This manual is designed to guide you through the proper programming and use of the AeGIS 400RTP Series. It is important for you to read and follow the manual completely. The AeGIS 400RTP Series comes with two years warranty, See section 1.4 for more detail. 1.
• Talk Time • Personal Access Code • Call Forwarding automatic or manual Technical Specifications: Power Input: 12VAC 20VA UL Listed Transformer (Pach supplied) or 12.0 VDC 20VA Current Consumption: 420mA idle, 620mA operation Emergency Battery: 12.0 VDC, 4Ahr rechargeable (not supplied) Night Light: 14V 0.080A 15,000 Average life hours Telephone Line: Standard voice grade RJ11 jack Operating Environment: Temp.
1.7 Warranty Pach and Company new products are warranted to be free of defects in material or workmanship for a period of two years, (24 months), from the date of purchase. This warranty extends only to wholesale customers who buy direct from Pach and Company or through Pach and Company’s normal distribution channels. Pach and Company does not warrant this product in any way to the end user consumer.
Pach and Company warrants the wiegand card, clam, and keyfob to be free of defects in material or workmanship for a period of three (3) months from the date of invoice. The above warranty is subject to the following conditions. 1. The products must be properly installed as specified; and maintained or used as intended. 2.
4. Under no circumstances will Pach and Company honor warranty any product found to have been altered, repaired, and/or modified by the end-user consumer. 5. Pach and Company reserves the right to replace a warranted product with a like product of equal value in the event original system cannot be repaired. 6.
9. Pach and Company warranty does not guarantee any product, new or repaired, to be free of operation error or service interruption in any way during the course of daily product operation 10. Pach and Company is not responsible for time, travel, and/or labor costs of any distributor and/or dealer-installer, including but not limited to, any expenses to install, uninstall or reinstall hardware/software/firmware related to warranty issues, product enhancements, or product failures.
CHAPTER 2. INSTALLATION A proper installation of the AeGIS system is very essential. You MUST follow the installation-wiring steps as shown in figure 2.1, 2.2, 2.3 and 2.4 Figure 2.1 Intercom with Dedicated Phone line Wiring Diagram Pach and Company AeGIS 400RTP Page 4 Chapter 2.
Figure 2.2 DSL Wiring Diagram Pach and Company AeGIS 400RTP Page 5 Chapter 2.
Figure 2.3 Dedicated Telephone Line Pach and Company AeGIS 400RTP Page 6 Chapter 2.
Figure 2.4 Intercom Wiring Diagram Pach and Company AeGIS 400RTP Page 7 Chapter 2.
CHAPTER 3. PROGRAMMING The AeGIS 400RTP can be programmed Local (using built-in keypad), Premise Phone or Remote Phone. Premise phone programming can only be used if the existing Central Office Line is connected to the system as shown in figure 2.1.
Function Local Programming Step 3 Enter 00 then #, you will hear “No Beep”. Premise Phone Remote Phone Step 4 Enter new 4-digit Master Code then press # then you will hear “One Short Beep” and proceed to step 5 or if you decided not to change the existing Master Code press ∗ to exit and you will hear “Three Short Beeps”. Step 5 Continue to program another parameter or press ∗ to exit; you will hear “Three Short Beeps”.
Function Delete or overwrite Individual Access Code Local Programming Premise Phone Step 1 Entering The Programming Must delete the individual access Mode: Press 0 and # simultaneously code from the local keypad. then release. If you are in the programming mode, proceed to step 2. Remote Phone Must delete the individual access code from the local keypad. Step 2 Enter the 4-digit Master Code (factory default is 0000) and you will hear “One Short Beep”.
Function Local Programming Premise Phone Step 1 Entering The Programming Pick up the phone and wait for a dial Mode: Press 0 and # simultaneously tone. then release. If you are in the programming mode, proceed to step 2. Step 2 Press # # and you will hear “One Short Beep”. Step 2 Enter the 4-digit Master Code (factory default is 0000) and you Step 3 Press # and you will hear “One Short Beep”. will hear “One Short Beep”.
Function Program Direct Call Forwarding 70 DIRECT CALL FORWARDING IS USED IF A DEDICATED PHONE LINE IS USED OR IF YOU WANT TO FORWARD THE CALL MANUALLY. NOTE: INTERCOM MODE IS DISABLED IF A PHONE NUMBER IS PROGRAMMED ON FUNCTION CODE 70 Local Programming Premise Phone Step 1 Entering The Programming Step 3 Press # and you will hear Mode: Press 0 and # simultaneously “One Short Beep”. then release. If you are in the programming mode, proceed to step 2.
Function Local Programming Premise Phone Remote Phone • “One Long Beep”, the master code is rejected and the connection will be disconnected. Step 3 Press 6, you will hear “Three Short Beeps” and the system disconnects the call. Program Step 1 Pick up the phone and wait Automatic or for a dial tone. Manual call forwarding Step 2 Press # # and you will hear “One Short Beep”. Step 1 Pick up the phone and wait for a dial tone. Step 2 Press # # and you will hear “One Short Beep”.
Function Local Programming Premise Phone “One Short Beep” and select another Step 5 Function Number (71 – 72). • Press “0” and #, you will hear “One Short Beep” and phone number Step 4 programmed is deleted or • Enter 0 then #, you will hear “One • Press “1” then press # you will hear Short Beep” and phone number “No Beep” and enter a new phone programmed is deleted or number up to 11-digit then press #, • Enter 1 then #, you will hear “No you will hear “One Short Beep”.
Function Local Programming Step 3 Enter 87 then #, you will hear “One Short Beep”. Premise Phone Step 5 • Press 1 (to enable) then press #, you will hear “One Short Beep” or Step 4 • Press 0 (to disable) then press #, • Press 1 then # to enable and you will you will hear “One Short Beep”. hear “One Short Beep” or • 0 then # to disable, and you will hear Step 6 Enter another function code to program a different parameter or “One Short Beep”.
Function Local Programming Step 4 Select the Automatic Call Forwarding Time (15 – 90 seconds) then #, you will hear “One Short Beep”. Premise Phone Step 6 Enter another function code to program a different parameter or exit the program by pressing ∗ ∗ and you will hear “Three Short Beeps”. Step 5 Enter another Function Code to program another parameter otherwise press ∗ to exit and you will hear “Three Short Beeps”.
Function Local Programming the door is already unlocked you will hear “One Short Beep” or • Enter 0 to Lock and you will hear “One Long Beep” then “One Short Beep”. Premise Phone Step 6 Enter another function code to program a different parameter or exit the program by pressing ∗ ∗ and you will hear “Three Short Beeps”. Step 5 Enter another Function Code to program another parameter otherwise press ∗ to exit and you will hear “Three Short Beeps”.
Function Local Programming Premise Phone Step 1 Pick up the phone and wait Step 1 Entering The Programming for a dial tone. Mode: Press 0 and # simultaneously then release. If you are in the proStep 2 Press # # and you will hear gramming mode, proceed to step 2. “One Short Beep”. Step 2 Enter the 4-digit Master Code (factory default is 0000) and you will hear “One Short Beep”. If you entered an invalid master code you will hear “One Long Beep”, repeat step 1.
Function Local Programming “One Short Beep”. Refer to Chapter 5 System’s Operation. Premise Phone Step5 Enter another Function Code to program another parameter otherwise press ∗ to exit and you will hear “Three Short Beeps”. Remote Phone Step 5 Enter another function code to program a different parameter or exit the program by pressing ∗ ∗ and you will hear “Three Short Beeps”.
Function Local Programming hear “Three Short Beep”. Premise Phone Step 1 Entering The Programming Step 1 Pick up the phone and wait Mode: Press 0 and # simultaneously for a dial tone. then release. If you are in the programming mode, proceed to step 2. Step 2 Press # # and you will hear “One Short Beep”. Step 2 Enter the 4-digit Master Code (factory default is 0000) and you Step 3 Press # and you will hear will hear “One Short Beep”. If you “One Short Beep”.
CHAPTER 4. OPERATIONS It is important for you to understand the system’s operations completely for the most ease of operations. You can enable or disable the system programming remotely via a touch-tone phone or locally via the system’s keypad. DESCRIPTION ACTION TO INITIATE THE CALL AND DISCONNECT THE CALL FROM THE AeGIS 400RTP.
DESCRIPTION ENABLE AND DISABLE CALL FORWARDING. ACTION Enable and Disable Function Code 70 via system’s keypad To enable: the call forwarding is automatically enabled if the phone number is programmed on function code 70 (see Chapter 3). To disable: Press * and 0 simultaneously, then 0#, you will hear “Three Short Beeps” the phone number on function code 70 will be deleted. Enable and Disable Function Code 71 and 72 Call Forwarding via system’s keypad (Local).
DESCRIPTION ACTION Step 5 Enter another Function Code to program another parameter otherwise press ∗ to exit and you will hear “Three Short ”. From Premise Location Step 1 Pick up your handset and wait for a dial tone. Step 2 Press # # and you will hear “One Short Beep” then Step 3 Press 9 to Unlock Cycle Relay 1 (door 1), you will hear “Two Short Beeps” or Press 8 to Unlock Hold Relay 1 (door 1), you will hear ” Two Short Beeps”.
DESCRIPTION ALARM NOTIFICATION ACTION Step 2 Dial the AeGIS phone number and you will hear “One Short Beep” if the gate is locked or “Two Short Beeps“ if the gate is unlocked. Step 3 Press # then 4-digit master code and you will hear “One Short Beep” if your master code is accepted or you will hear “One Long Beep” if your master code is rejected and the system will disconnect. Step 4 Press ∗, you are ready to talk to the AeGIS system. You may press “9” to open door or gate.
CHAPTER 5. TROUBLE SHOOTING GUIDES AUDIO PROBLEMS NO TONE WHEN KEYS ARE PRESSED. • In normal mode, No tone when the key is pressed unless if you are in programming mode. • Check the speaker and microphone connection on marked speaker and microphone (see fig.2.1). The snap on clip connector on the speaker and microphone connector must be facing inside the board. • Check the red and orange wires; make sure they are soldered into the speaker.
COMMUNICATION PROBLEMS THE SYSTEM DISCONNECTS WHEN THE TENANTS ANSWER THE CALL. • Check the distance between the system and the home phone, make sure it does not exceed the specification specified on Chapter 2. • If this is a new installation, remove the connection with the home phone and substitute with a telephone test set. • If this is an existing system, call Pach and Company Technical Support Department. HOME PHONE(S) HAS NO DIAL TONE. • If this is a new installation, • Check the wiring.
CHAPTER 6. PARAMETERS WORKSHEET You must keep accurate system’s parameters and database records at all time for future reference.
AeGIS 400RTP QUICK REFERENCE GUIDE TWO WAYS TO LOG IN TO PROGRAMMING MODE 1. Press 0 # simultaneously then release, enter the 4-digit master code. Default master code = 0000. A short beep if the master code is valid or a long beep if the master code is not valid or 2. Press on board round black button then then select the function code from the table. SYSTEM OPERATION TO CALL: Press # TO GRANT ACCESS TO A VISITOR: Press 9 (relay 1) or press 8 (relay 2) TO USE ACCESS CODE: Press * then 4-digit acces code.
