Product Manual

ManualsBrandsPacer ManualsHand OperatedHPN1A - Drum Pump w/ 8' Hose (Ag Chemicals Compatible)

The extension tubes are threaded at both ends. Extra exten-

sion tubes (#34) and couplings (#35) may easily be used

for deeper vessels such as tanks. Maximum suction lit is 15

feet.

1. A 55 gallon drum on end

requires 1 extension tube, 1

coupling and 1 suction tube

threaded together.

2. To use the side bung hole on

a 55 gallon drum thread together

one extension tube one coupling

, and a 5” length of suction tube.

The plastic tube can easily be

cut with a hacksaw. Make the

cut at an angle. DO NOT CUT

THE THREADED END.

3. For 275 gallon tanks, thread

together two extension tubes

and one suction tube.

OPERATION AND

SERVICE GUIDE

PO-1550H

JUNE 2011

OPERATOR’S MANUAL FOR DOUBLE

ACTING PISTON HAND PUMP

SAFETY WARNING

Verify the chemical compatibility of the materials of your pump with the liquid you want to pump. If you are uncer-

tain regarding chemical compatibility, contact your dealer for applications assistance and request a copy of our

Corrosion Resistance Charts. Do not use a pump that is not chemically compatible with the liquid you intent to

pump or serious bodily injury, death, ﬁ re, explosion or environmental damage could result.

Table of Contents

PLEASE READ SECTIONS I, II, III, IV AND VIII BEFORE OPERATING PUMP

I. UPON RECEIPT OF THE PUMP......................1 V. PUMP PARTS LIST............................. 3,4

II. DESCRIPTION .................................................1 VI, TROUBLE SHOOTING GUIDE........... 5

III. SAFETY PRECAUTIONS.................................2 VII. MAINTENANCE.................................. 5

IV. PUMP OPERATING INSTRUCTIONS..............2 VIII. SAFETY INFORMATION..................... 6

Page #

I. UPON RECEIPT OF PUMP

A. Inspect each pump for shipping damage immediate

ly upon receipt before signing for merchandise. If

any visible damage exists, note damage on shipping

bill of lading or receiving documents before signing.

Claims for damage must be made with the carrier.

Also, notify your dealer or distributor immediately of

any damage to the shipment.

B. Depending on model number and options ordered

the following parts are shipped loose in the carton

and should be checked before destroying the carton

and packaging material. See the drawing in section

V to help identify these parts.

1. - 1 bung adaptor #32

2. - 1 clamp #31

3. -1 hose #17, complete with: 1 hose adaptor

#21, 1 nozzle #15, 2 hose clamps #16

4. - 1 suction tube # 36

5. - 1 extension tube # 34

6. - 1 coupling # 35

7. - 1 discharge spout

II. DESCRIPTION

A. If you have not checked the chemical compatibility of your

pump with the liquid do it now before using the pump! The

pump is equipped in one of several ways. Compare your

model number with the model number chart immediately

preceding the parts list in section V. This will tell you what

materials make up your pump. Consult the factory for any

chemical applications. A chemical resistance chart is packed

with the pump.

B. The pump handle can be easily positioned either up for

normal use, or down, allowing the pump to be elevated. This

would be convenient for example when pumping from a truck

mounted drum or barrel. See section IV, step F.

C. A siphon breaker is built into the pump discharge. This

prevents siphoning from the drum if the hose drops from

its hanger. It also allows the hose to drain completely after

pumping.

D. The barrel is vented by 4 relief channels molded into the

bung adaptor. This prevents drawing a vacuum in the barrel.

E. The suction tube (#36) and extension tube (#34) supplied

are cut to ﬁ t a standard 55 gallon drum. The suction tube has

a bevel cut at one end and is threaded at the other end.

Summary of content (6 pages)

PAGE 1
OPERATOR’S MANUAL FOR DOUBLE ACTING PISTON HAND PUMP OPERATION AND SERVICE GUIDE PO-1550H JUNE 2011 SAFETY WARNING Verify the chemical compatibility of the materials of your pump with the liquid you want to pump. If you are uncertain regarding chemical compatibility, contact your dealer for applications assistance and request a copy of our Corrosion Resistance Charts.
PAGE 2
PO-1550H page 2 III. SAFETY PRECAUTIONS A. This manual contains important information for the safe and gloves, aprons, eye shields and adequate ventilation. Consult proper operation of this pump. Read it THOROUGHLY before chemical manufacturer for additional cautions. operating or installing the pump. H. Do not overtighten nonmetallic threaded fittings. One full turn B. USE ONLY ORIGINAL FACTORY REPLACEMENT PARTS. past hand tight is usually enough to prevent leakage. One roll C.
PAGE 3
PO-1550H page 3
PAGE 4
PO-1550H PO-1550H page 4
PAGE 5
PO-1550H page 5 VI. TROUBLE SHOOTING GUIDE A. pump will not prime 4. Valve leakage. Inspect poppet valves for weak springs or clogging. If pump was recently disassembled VERIFY PROPER POSITION OF VALVE SEATS. Refer to section VII.B1. 1. Clogged suction. Check that the suction tubes are clear and that the screen filter is not dirty or clogged. Use a pair of needle nose pliers or a stiff piece of wire to pull the suction screen from housing.
PAGE 6
VIII. GENERAL SAFETY INFORMATION FOR HANDLING FLAMMABLE AND COMBUSTIBLE LIQUIDS WARNING PO-1550H page 6 When using a hand pump to fill cans, drums or other portable or fixed containers with flammable or combustible liquids such as gasoline, both container being pumped from and the container being pumped to must be effectively BONDED and GROUNDED to prevent discharge of sparks of static electricity which could cause explosion.