User's Manual
Table Of Contents
- Chapter 1 Introduction
- Chapter 2 Overview
- 2.1 Overview of ONT-2-E4xxxi Multi-service Residential Gateway Series
- 2.2 EPON Multi-service Gateway Series Hardware Interface
- 2.3 Supported Residential Gateway (RG) Features
- 2.3.1 Network Address Translation (NAT)/NAPT (Network Address Port Translations)
- 2.3.2 Dynamic Domain Name System (DDNS)
- 2.3.3 Dynamic Host Configuration Protocol (DHCP) Client and Server
- 2.3.4 Security Firewall and Rich Packet Filtering
- 2.3.5 Advanced Quality of Service,
- 2.3.6 Virtual Server
- 2.3.7 Flexible Management Interfaces including Web GUI
- 2.4 Additional Features
- 2.5 Product Specifications
- 2.6 Physical Characteristics
- Chapter 3 Hardware Description
- 3.1 Package Contents
- 3.2 Accessories
- 3.3 ONT-2-E4xxxi Multi-service Residential Gateway Series Enclosure
- 3.4 LED Diagnostics on Front Panel
- 3.5 Rear Panel and Interface Description
- 3.6 Ethernet Connections
- 3.7 EPON SC/APC Fiber Optic Network Interface
- 3.8 Voice Telephony Interfaces (Standard Telephone)
- 3.9 RF Overlay
- 3.10 Power
- Chapter 4 Installing the ONT-2-E4xxxi Multi-service Residential Gateway Series
- 4.1 Cautions and Warnings
- 4.2 Pre-Installation Check
- 4.3 Tools and Materials Needed
- 4.4 System Requirements
- 4.5 Situating the EPON Multi-service Gateway ONT
- 4.6 Wall-Mounting the ONT Using the Fiber Tray
- 4.7 Wall-Mounting the ONT without the Fiber Tray
- 4.8 Vertical or Tower Mounting the ONT
- 4.9 Connecting the EPON Optical Fiber to the ONT
- 4.10 Connecting Telephones to the EPON Multi-service Gateway ONT
- 4.11 Connecting Premises LAN Ethernet Wiring
- 4.12 Connecting Power and Powering Up the ONT
- 4.13 Connecting to the GUI Interface of the ONT
- Index
ONT-2-E4xxxi Multi-service Residential Gateway Series Hardware Installation Guide
TM 87-10879 Rev. A UNRELEASED DRAFT 1
Chapter 1 Introduction
This guide introduces hardware components and installation procedures for the Aurora Networks
ONT-2-E4xxxi Multi-service Residential Gateway Series models and accessories. It provides infor-
mation you will need to install and set up the ONT-2-E4000i, ONT-2-E4020i, ONT-2-E4021i,
ONT-2-E4020iWn, ONT-2-E4021iWn, and ONT-2-E4001i models.
After you complete your installation, refer to the Aurora Networks ONT-2-E4xxxi Multi-service Resi-
dential Gateway Series Operator Guide for procedures for setting up your PC, logging in to the GUI
interface, and managing Residential Gateway and wireless features of the EPON Multi-service Gateway
ONT via the GUI.
1.1 Welcome
Thank you for taking the time to read the ONT-2-E4xxxi Multi-service Residential Gateway Series
Hardware Installation Guide. This manual contains information and procedures that will assist network
and field engineers with the installation and use of the ONT-2-E4000i, ONT-2-E4020i, ONT-2-E4021i,
ONT-2-E4020iWn, ONT-2-E4021iWn, and ONT-2-E4001i models.
1.2 About This Manual
The following information describes the ONT-2-E4xxxi Multi-service Residential Gateway Series
Hardware Installation Guide, the contents of its chapters, and the conventions it uses to present infor-
mation.
1.2.1 Conventions Used in This Guide
The following symbols represent the conventions used in this guide.
Symbol
Description
WARNING! This symbol is used to identify conditions or actions
that could seriously injure personnel; for example, an electrical
shock hazard.
CAUTION! This symbol is used to identify situations that present
minor hazards that can interfere with or threaten equipment or
system performance.
Note:
This symbol identifies important points related to the text.
Tip
This symbol provides helpful suggestions.