User's Manual
Table Of Contents
- Chapter 1 Introduction
- Chapter 2 Overview
- 2.1 Overview of ONT-2-E4xxxi Multi-service Residential Gateway Series
- 2.2 EPON Multi-service Gateway Series Hardware Interface
- 2.3 Supported Residential Gateway (RG) Features
- 2.3.1 Network Address Translation (NAT)/NAPT (Network Address Port Translations)
- 2.3.2 Dynamic Domain Name System (DDNS)
- 2.3.3 Dynamic Host Configuration Protocol (DHCP) Client and Server
- 2.3.4 Security Firewall and Rich Packet Filtering
- 2.3.5 Advanced Quality of Service,
- 2.3.6 Virtual Server
- 2.3.7 Flexible Management Interfaces including Web GUI
- 2.4 Additional Features
- 2.5 Product Specifications
- 2.6 Physical Characteristics
- Chapter 3 Hardware Description
- 3.1 Package Contents
- 3.2 Accessories
- 3.3 ONT-2-E4xxxi Multi-service Residential Gateway Series Enclosure
- 3.4 LED Diagnostics on Front Panel
- 3.5 Rear Panel and Interface Description
- 3.6 Ethernet Connections
- 3.7 EPON SC/APC Fiber Optic Network Interface
- 3.8 Voice Telephony Interfaces (Standard Telephone)
- 3.9 RF Overlay
- 3.10 Power
- Chapter 4 Installing the ONT-2-E4xxxi Multi-service Residential Gateway Series
- 4.1 Cautions and Warnings
- 4.2 Pre-Installation Check
- 4.3 Tools and Materials Needed
- 4.4 System Requirements
- 4.5 Situating the EPON Multi-service Gateway ONT
- 4.6 Wall-Mounting the ONT Using the Fiber Tray
- 4.7 Wall-Mounting the ONT without the Fiber Tray
- 4.8 Vertical or Tower Mounting the ONT
- 4.9 Connecting the EPON Optical Fiber to the ONT
- 4.10 Connecting Telephones to the EPON Multi-service Gateway ONT
- 4.11 Connecting Premises LAN Ethernet Wiring
- 4.12 Connecting Power and Powering Up the ONT
- 4.13 Connecting to the GUI Interface of the ONT
- Index
ONT-2-E4xxxi Multi-service Residential Gateway Series Hardware Installation Guide
4 UNRELEASED DRAFT TM 87-10879 Rev. A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
1.4.1 ONT-2-E4000i, ONT-2-E4020i, ONT-2-E4021i, and ONT-2-E4001i Models
The models that do not have Wi-Fi or wireless functionality meet the following regulatory requirements:
EMC
• 47 CFR 15 - Sub Part B, Class B
• EN 55022 - Radiated and Conducted Emission for ITE
• EN 55024 - Immunity for ITE
• ETSI EN 300 386 - Electromagnetic compatibility and Radio spectrum Matters (ERM)
• ICES-003 - Spectrum Management and Telecommunications Interference
• VCCI – EMI Requirements
• KN 22 - Radio disturbance characteristics
• KN 24 - Immunity characteristics
Safety
• IEC 60950-1 - ITE - Safety - General requirements
• EN 60950-1 - ITE - Safety - General requirements
• UL 60950-1 - Information Technology Equipment Safety
• CAN/CSA-C22.2 No. 60950-1 - Safety of Information Technology Equipment
1.4.2 ONT-2-E4020iWn and ONT-2-E4021iWn Models
The models that have Wifi or wireless functionality meet the following regulatory requirements:
EMC
• 47 CFR 15 - Sub Part C, Class B
• ETSI EN 300 328 - Electromagnetic compatibility and Radio spectrum Matters (ERM)
• ETSI EN 301 489-17 - Electromagnetic compatibility and Radio spectrum Matters (ERM)
Safety
• IEC 60950-1 - Safety - General requirements
• EN 60950-1 - ITE - Safety - General requirements
• UL 60950-1 - Information Technology Equipment Safety
• CAN/CSA-C22.2 No. 60950-1 - Safety of Information Technology Equipment
It is herewith confirmed to comply with the requirements set out in the Council Directive on the Ap-
proximation of the Laws of the Member States relating to Electromagnetic Compatibility