Instruction Manual

ManualsBrandsPace-Edwards ManualsCarBL Isuzu D-Max XSB

Part #: BL ISUZU D-MAX-0711

CANISTER PART # BL2072

(Picture shown may be different than

actual application)

(800) 338-3697

www.paceedwards.com

Pace Edwards Company

2400 Commercial Blvd.

Centralia WA 98531

ELECTRIC RETRACTABLE TRUCK BED COVER

TABLE OF CONTENTS

Tools Required for Assembly................................. 2

Before You Start ................................................... 2

Drain Hole Locations ............................................ 2

STEP 1: Remove Contents from Box ..................2

Packaging Contents ..............................................3

STEP 2: Install Wiring Harness ............................ 3

STEP 3: Place Canister Install Foam ................... 3

STEP 4: Install Rails............................................. 4

STEP 5: Installing Clamps....................................4

STEP 6: Lubricating the Sweep Seal ...................5

STEP 7: Connecting the Electronics ....................5

STEP 8: Installing Drain Tubes.............................5

STEP 9: Install Top Cover ...................................5

Release Handle Instructions ................................. 6

Helpful Maintenance Hints ................................... 6

Warranty Statement...............................................7

BLSP19

ISUZU D-MAX XSB

INSTALLATION INSTRUCTIONS

Summary of content (8 pages)

PAGE 1
ELECTRIC RETRACTABLE TRUCK BED COVER ISUZU D-MAX XSB INSTALLATION INSTRUCTIONS (Picture shown may be different than actual application) TABLE OF CONTENTS (800) 338-3697 www.paceedwards.com Pace Edwards Company 2400 Commercial Blvd. Centralia WA 98531 BLSP19 Tools Required for Assembly ................................. 2 Before You Start ................................................... 2 Drain Hole Locations ............................................ 2 STEP 1: Remove Contents from Box ............
PAGE 2
TOOLS REQUIRED FOR ASSEMBLY: 7/16” wrench or socket #2 Phillips screwdriver Wire cutters Tape measure 3/8” wrench or socket Note: There should be no drilling into the truck body needed on most standard or full-size trucks . BEFORE YOU START: Read the instructions carefully before you start. These instructions are written for one-person installation. We have noted where briefly having an extra person’s assistance can make installation easier.
PAGE 3
PACKAGING CONTENTS: Canister CAUTION! Rails Come in a separate Box. Rails (Left & Right) Clamp Pack DO NOT USE A KNIFE TO OPEN THE RAIL BOX. OPEN THE RAIL BOX ALONG THE LENGTH OF THE BOX AND LIFT RAILS OUT TO AVOID SCRATCHING THE SURFACE OF THE RAILS ON THE PACKAGE STAPLES.
PAGE 4
STEP 4: INSTALLING RAILS The machined end of the rail attaches to the canister. You will need to lift the hanging portion of the ribbed blanket and thread it in the rail while sliding the rail into the rail grip mounted to the ends of the canister (the underside of the blanket ribs need to nest on the gear). Make sure both flanges of rail slide into the rail grip. Rail Grips Push the rails forward against the canister. Complete for both left and right rails.
PAGE 5
STEP 6: LUBRICATING & PLACING THE SWEEP SEALS Locate the sweep seals (rubber weather strips) on the rails. Apply Pace Edwards’ UV Protectant (or 303 brand protectant) to a rag and wipe the underside of the sweep seal and the top of the wear strip. RAIL Extend the cover to the tailgate. Use an Allen wrench if needed to carefully draw out the sweep seal (seal should be angled outwards toward the cover – not rolled in toward the bed rail). (Fig.
PAGE 6
RELEASE HANDLE INSTRUCTIONS please do not hesitate to call us at: (800) 338-3697 and ask for our technical service department. You have now completed the installation of the Bedlocker Electric hard tonneau cover. If you have any questions If power is lost to the Bedlocker unit or the electric drive system fails to operate and you have to use the cover right away you can do the following to open or close the cover: RELEASE HANDLE 1.
PAGE 7
C O N G R AT U L AT I O N S ! On your purchase of a Pace Edwards Retractable Truck Bed Cover. We are confident that you will get many years of trouble free service from this accessory to your truck. Please take a moment to fill out the warranty registration form to activate warranty coverage of your truck bed cover. PACE EDWARDS PRODUCT WARRANTY PACE EDWARDS (hereinafter referred to as the MFG.
PAGE 8
2400 Commercial Blvd, Centralia, WA 98531 USA (360) 736-9991 (main) (360) 736-9992 (fax) (800) 338-3697 (toll-free) www.paceedwards.