User Manual
#,20 #,,=.30'%;<,C?9..0==:<40=
..0==:<40=1:<'?>:8,>4.%;<,C?9
56. ! 45° Elbow
57. ! 90° Elbow
58. ! Nylon Washer
B>09=4:9=!,9/$0,/=:97C
• 092>3%4D0=-3, -6, -12, -18, -24
59. Extension L/Needle (Select Size)
*%>,4970==%>007B>09=4:9=*4<.,;=:97C
• 092>3%4D0=-3, -6, -12, -18, -24, -36, -48
60. * St. St. Extension L/Needle (Select Size)
B>09=4:9!00/70=*B>09=4:9=
• Length Sizes: -3, -6, -12, -18, -24, -36, -48
61. St. St. Extension Needle (Select Size)
Q
77*4<.,;=8?=>?=0 ,#<0==?<000/
?; :< #<0==?<0 &,96 >: 100/ 8,>0<4,7 -0492
=;<,C0/ 7A,C= ,/5?=> ,>:84D492 ,4< ;<0==?<0
34230<>3,917?4/,4<;<0==?<0
*%>C70&4;=,9/4<.,;=*B>09=4:9="97C
62. * Tip
63. *$ Aircap External Round Pattern
64. * Aircap External Fan Pattern
65. * Aircap Internal Fan Pattern
66. * Aircap Internal Fan Pattern
67. * Aircap Internal Fan Pattern
68. * Aircap Spherical Pattern
69. * Aircap Radial Pattern
70. * Aircap Internal Fan Pattern
71. *$ Aircap Internal Round Pattern
72. *$ Aircap Internal Round Pattern
&$"'%""&!%#$+#&&$!%
(A) $"'"$%&##!% is due to low or restricted flow
of air pressure or too heavy materials being applied with spray
gun too close to surface.
(B) )&"$ %!!% is due to low air pressure or
restricted flow of air, material being too thin, applied too close
to the surface.
(C) %#'&&$!%#$+ is caused by air leaking into fluid line
or can be caused by a loose fluid tip, a broken or split tip,
lumpy material, a clogged vent hole in cover of material cup,
air leak at fluid pipe attached to inside of tank cover, or a
clogged paint strainer.
&" "$$& Tighten tip securely or replace. Strain
materials and clean strainer. Sputtering might also be caused
by worn packing washers, or worn or scored needle.
(D) ! $ ! %#$+ #&&$! is caused by dried
material accumulated in one fan port of the multiplehead
distorting the pattern.
&""$$&: Dissolve material inside fan port with suitable
solvent applied with a small brush.
!"&!0@0<?=0A4<0:<=3,<;49=><?809>=>:.70,91,9
;:<>=,=;0<8,909>/,8,20>:>30,4<;:<>=A477<0=?7>49
/0=><:C492?941:<84>C:1>301,9;,>>0<9
(E) '!!! %#$+#&&$!, heavy on one side,
may be caused by material collecting around outside of the
fluid tip and aircap, or by a loose aircap.
&""$$&Remove aircap and clean fluid tip and aircap
with solvent, dry with air pressure. Always be sure fan aircap
and aircap body is tightened securely.
(F) (+!&$ in a fan pattern is caused by insufficient air
pressure at the fan port. Rough or shady edges are also
caused by low air pressure.
&""$$&Increase air line pressure.
(G) %#&!%#$+#&&$!heavy on each end and light
in the center, is caused by excessive air pressure.
&""$$&Reduce air pressure.