User Manual

ASSEMBLY INSTRUCTIONS
STEP 1: Spread tent out flat,
floor side down.
TO IMPROVE THE WEATHER RESISTANCE OF YOUR TENT, IT IS ADVISABLE
TO USE SEAM SEALER TO COAT ALL EXPOSED SEAMS. YOU SHOULD APPLY
ONLY TO THE INSIDE SEAMS OF THE TENT AND UNDERSIDE OF THE TENT
FLY. IF APPLIED TO THE OUTSIDE SEAMS, DISCOLORATION OF YOUR TENT
MAY OCCUR. SEAM SEALER IS AVAILABLE IN THE CAMPING SECTION OF
ANY LOCAL SPORTING GOODS STORE.
IMPORTANT: WE ADVISE YOU TO ASSEMBLE THE TENT ONCE BEFORE
GOING CAMPING TO BECOME FAMILIAR WITH THE ASSEMBLY OF THE TENT.
TO PROLONG THE LIFE OF THE TENT FLOOR, SELECT A LEVEL, CLEAN AREA
FOR THE CAMPSITE. TO PREVENT DAMAGE TO THE ZIPPER, UNZIP THE
DOORS TO ALLOW AIR TO ENTER THE TENT.
NOTE: To take down tent, follow steps above in the reverse order. Be sure to
leave doors and windows unzipped. Make sure tent is clean and dry
before storing. Place stakes into stake bag and poles into pole bag, which
are provided. The tent should be folded into equal parts toward the center of
the tent to distribute the bulk. Fold fly and lay on top of tent. Start a small tight
roll, the width of your carry bag, at the end opposite the doors. Roll tent around
the pole bag toward doors to allow air to escape. Once rolled, tie a string around
tent to hold in place. Place tent and stake bag into carry bag.
MODEL WDC2001 1-Person Backpacking Tent 7’5” x 2’5“
NOTE: PLEASE LOOK AT THE REPLACEMENT PARTS DIAGRAM TO SEE
HOW YOUR FRAME IS ASSEMBLED.
NOTE: The zippered vestibule can be guyed out using trekking poles.
Requries additional guy lines, stakes + trekking poles (Sold separately).
STEP 2: Extend the fiberglass poles by pulling out each section and placing
ends into the metal ferrule connectors.
STEP3: Lay the poles from corner to corner crossing at the center of the tent.
STEP 4: Insert the pole ends into the grommets at the back
corners of the tent. Clip the plastic hook just above the grommet
to the pole. Move to the front of the tent and gently flex one
pole into an arch and place the pole end into the grommet.
Clip the plastic hook just above the grommet to the pole. Repeat
for the second pole.
STEP 5: Move the poles upward forming two arches that cross at the center of
the tent.
STEP 6: Locate the hook attached to the center of the tent
roof and hook it over both poles.
STEP 7: Work around the tent attaching all the remaining
clips to the poles.
STEP 8: Stake down the tent by inserting tent stakes through
the stake loops at each corner of the tent. Hammer the stakes
into the ground at a 45° angle, by using a hammer or mallet.
Make sure to pull tent floor out even and tight.
Tent should appear
as shown.
STEP 9: Unfold the fly and place it over the tent, making certain the vestibule
zippers are placed over the door.
STEP 10: Fasten the buckles on the fly to the corresponding
buckles at the base of the tent. Adjust the webbing at the
buckles to make fly snug.
STEP 11: Fasten the Velcro fasteners sewn to the edge of
the fly around the tent poles.
STEP 12: Stake down the front of the vestibule by inserting
stakes through the webbing loops at each corner. Hammer
the stakes into the ground at a 45° angle, by using a hammer
or mallet. Make sure to pull tent vestibule out evenly.
STEP 13: There are guy ropes located on the fly of the tent.
Extend the guy ropes and make a loop at opposite end of
rope by using the slider (as shown) and place loop over a
tent stake. Adjust the slider to make the guy rope tight and
stake to the ground.
Assembled tent should
appear as shown
A
A