User Manual

ManualsBrandsOzark Trail ManualsOutdoor SportsHazel Creek 14 Person Family Cabin Tent

ASSEMBLY INSTRUCTIONS

MODEL NO W967 - 14P Cabin Tent with Convertible Screen Room

IMPORTANT: WE ADVISE YOU TO ASSEMBLE THE TENT ONCE BEFORE

GOING CAMPING TO BECOME FAMILIAR WITH THE ASSEMBLY OF THE TENT.

NOTE: PLEASE LOOK AT THE REPLACEMENT PARTS DIAGRAM TO SEE HOW

YOUR FRAME IS ASSEMBLED.

TO PROLONG THE LIFE OF THE TENT FLOOR, SELECT A LEVEL, CLEAN AREA

FOR THE CAMPSITE. TO PREVENT DAMAGE TO THE ZIPPER, UNZIP THE

DOORS TO ALLOW AIR TO ENTER THE TENT.

TO IMPROVE THE WEATHER RESISTANCE OF YOUR TENT, IT IS ADVISABLE

TO USE SEAM SEALER TO COAT ALL EXPOSED SEAMS. YOU SHOULD APPLY

ONLY TO THE INSIDE SEAMS OF THE TENT AND UNDERSIDE OF THE TENT

FLY. IF APPLIED TO THE OUTSIDE OF SEAMS, DISCOLORATION OF YOUR

TENT MAY OCCUR. SEAM SEALER IS AVAILABLE IN THE CAMPING SECTION

OF ANY LOCAL SPORTING GOODS STORE.

STEP 1: Spread tent out flat, floor side down.

Unzip the doors.

Tent should

appear as shown.

Tent should

appear as shown.

STEP 6: Extend each of the six steel poles, by pulling out each

wire-corded section and placing the jointed ends into the connected

pole sections. The 4 poles with no D-rings are the corner upright

poles (C). The 2 poles (D) with the D-Rings near one end are the

center upright poles.

STEP 13: Secure the tent to the fly by wrapping the Velcro

fasteners at the edge of the fly around the metal tent poles

as well as securing the ties on the underside of the fly to the

corner joints.

STEP 2: Stake tent to the ground by

inserting metal stakes through the rings

located at each tent corner. Hammer

the stakes into the ground at a 45°,

making sure to pull tent floor out even

and tight. Continue to stake down all intermediate stake loops.

STEP 3: Locate the three fiberglass tent poles. Extend each fiberglass pole by

pulling out each section and placing the ends of the pole sections into the metal

connecting ferrules. The two longer poles (A) are the main roof poles, which run

corner to corner across your tent roof. The third pole (B) is the center ridge pole

which is marked with white tape.

STEP 4:

While making sure the sleeves

are in line with each other, slide each

main roof pole (A) through the blue

sleeves that are opposite each other on

the roof of the tent. Next insert the center

roof ridge pole (B) though the grey sleeves.

Be sure that all the poles go through the

loop at the center top of the tent.

STEP 5: Locate the plastic corner joints (E) that are attached

to the tent canopy and attach them to the ends of the fiberglass

poles. The smaller opening of the corner joints with “teeth” fit

over the roof poles.

STEP 7: With an adult on each corner at one end of the tent, insert the ends

of the steel corner upright poles (C) into the bottom openings of the plastic

corner joints (E).

STEP 8: Each adult should lift up on the steel pole and while

raising one side of the tent, place the bottom end of the steel

poles onto the pins attached to the rings at the base of the tent.

STEP 9: Using the two center upright poles (D) with the D-rings near the top

repeat steps 7 and 8 at the center of the tent.

STEP 10: Using the two remaining corner upright poles (C) repeat steps 7 and

8 at the remaining 2 corners of the tent.

STEP 11: Clip the plastic hooks on the tent walls around the steel poles.

STEP 12: Unfold the fly and place it over the tent, making

certain that triangular panels on the fly are placed at the

corners of the tent. Attach the hooks at the four corners of the

fly to the metal rings at the base of the tent. Attach the hooks

at the edge of the fly to the D-Rings on the center upright poles.

STEP 14: Guy ropes have been provided for the tent. Extend

each of the guy ropes and make a loop at the opposite end by

using the slider (as shown). Place the loop over tent stake and

stake to the ground. Adjust the slider to make guy rope tight.

WARNING: Elastic cords can snap back and hit your eye.

To reduce the risk of injury to you and others:

• Keep your body and face clear.

• Do not over stretch elastic cords.

• Maintain firm grip on hook.

• Pull the hook toward you; if it slips it will spring away from you.

• Make sure hook is fully clipped to tent before releasing.

• Wear protective eye wear during tent assembly.

Your failure to follow this warning could cause serious injury or permanent disability.

NOTE : To take down tent, follow steps above in the reverse order. Be sure to leave

door and windows unzipped. Place stakes into stake bag and pole into the pole bag,

which are provided. Make sure tent is clean and dry before storing. The tent

should be folded into equal parts toward the center of the tent to distribute the bulk.

Start a small tight roll, the width of the carry bag, with the pole bag placed at the

end opposite the door. Roll tent toward door to allow air to escape. Once rolled, tie

a string or rope around tent to hold into place. Place tent, frame and stakes into carry bag.