OPERATOR’S MANUAL BEAM CLAMP 100% made in the USA. 1 TON THROUGH 10 TON These Beam Clamps meet or exceed ASME standards (For use with manual or powered hoists) pg.1 P.O. Box 845, Winona, MN 55987 Phone (800) 749-1064 (507) 474-6250 Tech Support (507) 457-3346 Fax (507) 452-5217 sales@ozliftingproducts.com www.ozliftingproducts.
Table of Contents Pg.2 . . . . . . . . . . . . . . . . . . . . . . Product Features Pg.3 . . . . . . . . . . . . . . . . . . . . . . Warranty Pg.4 . . . . . . . . . . . . . . . . . . . . . . Important Information and Precautions Pg.5 . . . . . . . . . . . . . . . . . . . . . . Warnings Pg.6 . . . . . . . . . . . . . . . . . . . . . . Technical Information/ Pre-Installation Pg.7 . . . . . . . . . . . . . . . . . . . . . . Operation/Maintenance Check out our How to Videos at www.ozliftingproducts.
Warranty This product is guaranteed to be free of defects in materials and workmanship for five years from date of shipment. This does not apply to any product showing signs of misuse, overloading, alteration, improper maintenance, or negligence. Normal wear and tear of moving parts is excluded from this warranty.
Important Information and Precautions This manual contains general instructions dealing with the normal installation, operation and maintenance of the products described herein. This product should not be installed, operated, or maintained by any person who has not read all the contents of these instructions. Failure to read and comply with these instructions, warnings, or limitations noted might result in bodily injury, death, or property damage.
Warnings Failure to read and comply with the following warnings may result in a hazardous situation that could lead to death, serious injury, or property damage. Be sure to properly install, operate, and maintain the Beam Clamp so that it does not come off the beam. Do Not lift more than the designated load range. Do Not lift people or lift loads over people. Do Not operate a damaged or malfunctioning product. Do Not remove, deface, or cover warning labels.
Technical Information (1, 2, 3, 5 and 10 tons) B A C D F G H E Specification OZ1BCA OZ2BCA OZ3BCA OZ5BCA OZ10BCA Safe Working Load 2,000 lbs. 4,000 lbs. 6,000 lbs. 10,000 lbs. 20,000 lbs. A 3” - 9” 3” - 9” 3.5” - 13” 3.5” - 13” 3.5” - 13” B 14.75” 14.75” 20.5” 19.5” 22” C 2.51” 2.91” 3.94” 4.41” 4.72” D 0.9” 0.9” 1.5” 1.5” 1.6” E 9.5” 9.5” 11” 11” 11.5” F 4.75” - 5.75” 4.75” - 5.75” 7.5” - 9” 7.5” - 9” 5.5” - 9.375” G 1.75” 1.75” 2.5” 2.5” 4” H .
Operation Warnings & Precautions Beam Clamp operators should read and fully comprehend this entire manual and all warnings on the clamp before beginning clamp operation. If this manual is not read and followed completely injuries may occur. Operator Requirements: Must be trained in proper clamp operation and dealing with potential malfunctions. Should not operate beam clamp while under influence of alcohol, medications, or drugs. Should not operate the beam clamp while tired or distracted.
P.O. Box 845, Winona, MN 55987 Phone (800) 749-1064 (507) 474-6250 Tech Support (507) 457-3346 Fax (507) 452-5217 sales@ozliftingproducts.com www.ozliftingproducts.com Rev.
