S5 User Manual 3.1.2 Dolby Atmos Soundbar Before using the machine, please read the instructions carefully and keep them for future reference.
Safety information AC Voltage: This symbol indicates that the rated voltage shown with this Safety warning To prevent electric shock, do not open the back plate. There are no internal parts that can be repaired by the user. If maintenance is needed, please have special service personnel carry out maintenance. See the table below for a description of the symbols that may appear on your OXS S5 products. symbol is AC voltage.
Clean Warning Matters needing attention 1.Make sure the AC power supply in your house meets the power requirements listed on the label Before cleaning, be sure to turn off the system and unplug the power adapter from the power outlet. sticker at the bottom of the product. Please mount the product horizontally on the appropriate base (furniture) and leave enough ventilation space around 7~10 cm.Make sure the vents are not blocked.
Directory S5 .......................................................................................................................................................................... 1 3.1.2 Dolby Atmos Soundbar .......................................................................................................................... 1 1. Check the components ............................................................................................................................ 1 2.
1. Check the components No Unit Quantity 1. Soundbar 1 2. remote control 1 3. AAA Battery 2 4. Power cord 1 5. Power cable 1 6. Optical fiber line 1 7. HDMI cable 1 8. Wall mount screws 2 9. User manual 1 10. Quick Start Guide 1 • X1 X1 X2 X2 X1 X1 X1 X1 For more information about power supply and power consumption, see the label that comes with the product.
2. Overview of the product Top panel of Soundbar 1 Standby button In standby mode, press the standby button to turn on speaker system 2 Volume up button and down button Adjust the volume 3 Audio source selection button TV->HDMI1->-USB->Optical->BT->AUX 4 Bluetooth Switch to Bluetooth source, or Bluetooth pairing 5 display Displays system status and current mode. When plugged into the power supply, the power button will start working within 3 seconds.
Soundbar interface panel 1 DC Connect the DC power supply to the speaker system. 2 Aux Connect external analog audio inputs. 3 USB For USB Playback and after sale service only. 4 5 OPT Digital (optical cable) output connected to external devices. (see page XX) HDMI1 Use HDMI cable to input digital video and audio signals simultaneously. Connect to the HDMI output of external devices. (See page XX) 6 HDMI Out ( eARC/ARC) Connect to the HDMI jack on your TV.
3. Remote Control Key Instructions for Remote Control 1 Turn on and off the soundbar. • Auto Standby will automatically shut down in the following cases: In AUX /OPT/ TV/HDMI /BT mode, up to 15 minutes if no audio signal is present. In standby mode, press the standby button to run the speaker. 2 You can select Standard, Voice, Music, Cinema, and Night to set the desired sound mode. • STANDARD Output standard sound.
system. 5 If pressed, the Settings items are displayed in order, such as BASS, TREBLE,CENTER LEVEL, FRONT TOP LEVEL and sync. You can use left/right keys to adjust the desired items. To control the volume of TREBLE or BASS, select – Treble or Bass in the Sound Settings, and then use the Up/Down buttons to adjust the volume between -6 and +6.
Output configuration for different sound modes SOUND MODE INPUT Source S5 output STANDARD 2.0 channel 2.1 channel 5.1 channel 3.1 channel 7.1 channel 3.1 channel 3.1.2 channel 3.1.2 channel 2.0 channel 2.1 channel 5.1 channel 3.1 channel Atmos, 7.1 channel 3.1 channel SOUND 3.1.2 channel 3.1.2 channel 2.0 channel 2.1 channel that can 5.1 channel 3.1 channel selected 7.1 channel 3.1 channel using 3.1.2 channel 3.1.2 channel Sound 2.0 channel 3.1.2 channel Mode 5.
4. Connect the subwoofer and rear surround speakers Connect power and device Please use the power cord to connect thesoundbar speaker to the power outlet in the following order: See the label that comes with the product for more information about the power supply required and power consumption. (Label: Label of the thesoundbar) 1. There will be sound bar connected to the power supply.
2. Press again to shut down. System will go to Standby mode. In STANDBY mode sound bar’s screen show "--" . 3. If no input, no operation and silent state after 10 minutes, sound bar goes into Standby automatically. 4. Disconnect the mains plug from the Power outlet if you want to switch the unit off completely.
Attention When both the HDMI cable and the cable are connected, the HDMI signal is received first. To connect the HDMI cable between the TV and the soundbar, make sure to connect the terminals marked ARC or eARC. Otherwise, the TV sound may not be output. Be sure to use a cable with an advanced HDMI certification mark. Method 1. Connecting through HDMI Connect to a TV that supports HDMI ARC (Audio Return Channel) 1.
Method 2. Connecting through optical cable Check before connection 1. When both the HDMI cable and the cable are connected, the HDMI signal is received first. When you are using cable and the terminals have a cover, be sure to remove the cover. Optical cable is used to connect the OPTICAL port on the speaker interface board and the OPTICAL output port on the TV with the TV and the active home speaker off. 2. Turn on the soundbar and TV. 3.
7. Use a wireless connection to the TV Mode 1. Connecting via Bluetooth When using Bluetooth to connect to the TV, you can hear the stereo sound without wiring. Only one TV can be connected at a time. You can connect to a Bluetooth-enabled TV. Check the specs of your TV. 1. Long Press the Source button on the remote control under the BT source to enter the "PAIRING" mode. a).
If the device connection fails If you already have an active host speaker on your TV's speaker list (such as the OXS S5), remove it. Then repeat steps 1 through 3 Disconnecting sound barfrom TV Long press Bluetooth button on the top of sound bar or the (source) button on the remote control. Disconnection takes some time because the TV must receive a response from the soundbar. (The time required may vary, depending on the model.
8. Connecting external devices Check the list before connecting Dolby Atmos® is supported in HDMI mode only. If the audio output option includes Auxiliary Audio, be sure to set Auxiliary Audio to Off. Make sure the content supports Dolby Atmos®. Method 1. Connecting with HDMI Cable (Dolby Atmos decoding and playback) 1. Use an HDMI cable to connect the HDMI OUT port on the external device and the HDMI port on the back of the active home speaker.
2. Use an HDMI cable TO connect the HDMI IN port on the TV and the HDMI TO TV (EARC /ARC) port on the back of the active home speaker. 3. Turn on active speakers, TVs, and peripherals. 4. Select "HDMI” modes by pressing the (source) button on the top of the active home speaker or the (Source) button on the remote. 5. The display indicates that "HDMI” modes are currently selected, and the sound bar will start playing sounds. NOTE When you use Dolby Atmos® : 3.1.
2. Turn on the soundbar and external devices. 3. To select "OPT" mode, press the (source) button on the top of the soundbar or the (source) button on the remote control 4. Your soundbar will play sounds from external devices. 9. Connecting mobile devices Mode 1. Connecting via Bluetooth When using Bluetooth to connect a mobile device, you can enjoy a wireless stereo experience. When connecting to a new Bluetooth device, make sure the device is within 1 meter.
1. Long Press the Source button on the remote control under the BT source to enter the "PAIRING" mode. (or) a). Press the Bluetooth button on the top panel, and then select "BT" mode "BT" automatically changes to "PAIR" in a few seconds or to blinks "BT" if there is a Bluetooth connected before. b). If "BT" appears and doesn’t blink. A device has already been connected to the soundbar via Bluetooth.
– Electrical changes may occur when there is an obstruction, such as a wall or partition, at or near a corner. – When exposed to radio interference caused by other products operating in the same frequency range, such as medical devices, microwave ovens, and wireless LAN devices. – 10. Obstacles such as doors and walls may affect sound quality even if the device is within the effective range. USB Playback User can play music files stored on a connected USB device. 1.
Don’t remove the USB device during operation. To avoid data corruption or damage to the USB device, turn the speaker system off before connecting or removing the USB device. Some files may not play depending on the file format, file encoding, recording condition, or other conditions. Some files edited on a PC may not play. Fast forward or fast reverse may not be available with some files. The speaker system does not play coded files such as DRM.
to securely install the expansion screw on the wall-hanging bracket. Installation of rear speakers on the wall matters needing attention Rear speaker wall mount must be able to support more than 5. 0 kg. OXS is not responsible for any damage to the product due to improper installation. Be careful not to install the rear speakers on the side or upside down. 12.
For the TV's sound output, choose the soundbar. Cable connections to the soundbar should not be loosened. Unplug the cable and reconnect. Unplug the power cord completely, reconnect, and then switch on the power. Initialize the product and retry. 5 The TV is not connected via HDMI Check that the HDMI cable is not properly connected to the ARC terminals.(see page13). TO TV (EARC /ARC) You may not be able to connect to external devices (set-top boxes, game consoles, etc.).
9 Soundbar is not turned on after the If you turn off the sound bar while watching TV, power TV is turned on synchronization with the TV is disabled. Turn off the soundbar manually or restart the TVonce. 13. The license Manufactured under license of Dolby Laboratories.Dolby, Dolby Atmos, Dolby Audio, Dolby Digital Plus, and the double D symbol are trademarks of Dolby Laboratories.
14. Legal&Compliance FCC Class B Radio Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Software Licenses All software is provided subject to software license agreements and you agree that you will be bound by such license agreements in addition to other applicable terms of use.
17. Specifications MODEL OXS S5 WEIGHT(NET) 4.2 kg DIMENSION(WXHXD) 1100mmx170mmx120mm OPERATING + 5 ° C to + 35 ° C TEMPERATURE RANGE OPERATING HUMIDITY 10 to 75 percent RANGE AMPLIFIER (20W x 3) + (20W x 2) RATED OUTPUT POWER REQUIRMENT INPUT 220 V - 240 V AC, 50 Hz/60 Hz, 24V 3A SUPPORTED Dolby Atmos (True HD/Digital Plus), Dolby Digital, *.wav,*.mp3 PLAYBACK FORMATS CONNECTIONS One 3.5mm Stereo Audio One Optical (Toslink) HDMI (eARC) HDMI In One 3.
Hazardous substance information in the product Part name Harmful substances lead mercury cadmium Six price Polybrominate Polybrominat (Pb) (Hg) (Cd) Cr(VI) d ed biphenyls (PCBS) disylenethers (PBB) (PBDE) x ○ ○ ○ ○ ○ The metal part x ○ ○ ○ ○ ○ cable x ○ ○ ○ ○ ○ Plastic ○ ○ ○ ○ ○ ○ Printed circuit board assembly products This form is prepared in accordance with SJ/T 11364 O: denotes that the content of the hazardous substance in all homogeneous materials of the
products recycling and processing, and hand it over to the local manufacturer with the state-recognized recycling and processing qualification for recycling and processing.
