User Guide

Installation Instructions
When adding a second layer of insulation in the
attic, unfaced should always be used so that
moisture is not trapped inside the insulation.
1. Temporary flooring should be laid across the
joists to provide some footing, and a temporary
work light should be installed.
2. Lay the insulation blanket at the outer edge
of the attic space and work toward the center.
This allows for more headroom in the center of
the space, where cutting and fitting can be done.
It’s also a good idea not to get “insulated into a
corner” where it will be hard to get back to the
attic access.
3. If the joist cavities are completely lled to the
top of the joists, lay the new insulation in long runs
perpendicular to the direction of the joists, and use
leftover pieces for small spaces. If the cavity is not
completely filled, use the appropriate thickness of
insulation to fill it to the top, then add an additional
layer of insulation in a perpendicular direction.
4. The insulation should extend far enough to
cover the tops of the exterior walls, but should not
block the flow of air from the soffit vents. To make
sure the soffit vents aren’t blocked, install attic
vents or baffles like Owens Corning raft-R-mate
®
Attic Rafter Vents, which assure unrestricted
airflow from the soffit into the attic.
5. Insulation should be kept 3" away from
recessed lighting fixtures unless fixtures are
marked “I.C.” (Insulated Ceiling) — designed for
direct insulation contact. If insulation is placed
over an unrated fixture, it may cause the fixture to
overheat and perhaps start a fire. The insulation
should always be installed at least 3" away from
any metal chimneys, gas water heater flues or
other heat-producing devices.
6. Fill the spaces between a masonry chimney
and wood framing with a noncombustible material,
such as unfaced EcoTouch
®
insulation, which will
not burn.
NOTE: Do not leave faced insulation exposed.
The facings on kraft-faced insulation will burn and
must be installed in substantial contact with an
approved interior finish as soon as the insulation
has been installed. Facing must be installed in
substantial contact with an approved ceiling,
floor or wall material. Keep open flame and other
heat sources away from facing. See package
for warnings, fire hazard and instructions, or call
1-800-GET-PINK
®
.
Check your local building codes for requirements in
your area.
Project: Adding Insulation to an Attic
1
Certied by Scientic Certications Systems to have a minimum of 55% recycled glass content.
2
This product has achieved GREENGUARD GOLD Certification and is verified to be formaldehyde free. GREENGUARD Certified products are certified to GREENGUARD standards for low
chemical emissions into indoor air during product usage. For more information, visit ul.com/gg.
THE PINK PANTHER™ & © 1964–2015 Metro-Goldwyn-Mayer Studios Inc. All Rights Reserved. The color PINK is a registered trademark of Owens Corning. © 2015 Owens Corning. All Rights Reserved.
Know-How
• Before you begin any insulation project make
sure you:
• Seal any open penetrations
• Gather the necessary tools and wear
protective gear listed above
• Always use a portable work light to
ensure you have enough light in your
work environment
• Leave EcoTouch® PINK
®
insulation in its
wrapper until you are ready to use it
• Packaged insulation is highly compressed
and expands greatly when the wrapper is
opened
• Provide a safe place to sit or kneel in an
unfinished attic and a surface on which to cut
the insulation
• Use a pole or rake for pushing insulation into
out-of-the-way places in attics/flat ceilings
• Properly insulate and seal attic access
openings
Owens Corning is fully committed to safety and
believes accidents are preventable. Please join us
by promoting safety where you live and work.
Basic Tools
• Tape measure
• Utility knife
• Straightedge or 2 x 4 (for cutting insulation)
• Lightweight, squeeze-type stapler
Protective Gear
• Work gloves
• Loose-tting, long-sleeved shirt
• OSHA-approved safety glasses
• Disposable dust mask
Special Equipment
• Portable work light
• Boards or sheets of plywood (provide a safe
place to sit or kneel in an unfinished attic and
a surface on which to cut the insulation)
• Pole or rake (for pushing insulation into
out-of-the-way places in attics/flat ceilings)