Woodcrest® & Woodmoor ® Shingles Installation Instructions Instrucciones Para La Instalación De Tejas Woodcrest® Y Woodmoor® Woodcrest & Woodmoor ® ® Shingles
Application Instructions: Instrucciones para la aplicación: Before installing this product, check local building codes for their roofing requirements. Antes de instalar este producto, consulte los códigos de construcción locales para informarse sobre los requisitos de techado. These laminated shingles are designed for new or reroofing work over any properly built and supported wood roof deck having adequate nail holding capacity and a smooth surface.
1 2 Specialty Eave Flashing: WeatherLock® underlayment or equivalent eave and flashing membrane applied to a point at least 24" beyond interior wall line. See manufacturer’s installation instructions. See Fig. 1. Underlayment: Standard Slope (4" in 12" or more): Application of underlayment, metal drip edges, and eaves flashing: See Fig. 2. Low Slope (2" in 12" to less than 4" in 12"): Application of underlayment and metal drip edges: See Fig. 2A.
3 Starter Course: Left Rake Application: Cut 35" off from the first bottom starter piece. Fasten the remaining 5" x 133⁄ 8" to the deck as shown in Fig. 3, followed by a full 133⁄ 8" x 40" starter piece to the deck with 5 fasteners as shown. Right Rake Application: Cut 5" off from the first bottom starter piece. Fasten the remaining 35" x 133⁄ 8" to the deck as shown in Fig. 3, followed by a full 133⁄ 8" x 40" starter piece to the deck with 5 fasteners as shown. Fig.
5 Mansard or Steep Slope Fastening Pattern: Fig. 5 See Fig. 5.
Borde de viga inclinada 8 Fig. 8 Fig. 8 rse cou 1 1st ilera40" H 8 Fig. 8A Shingle Application 5" & 15" offset pattern Shingle Application 5" & 15" offset pattern Shingle Application 5" & 15" offset patternde hileras de 5 5" & 15" Course Application: Colocación Aplicación 5 pulg. y 15 Aplicación de®tejas en patrón de desplazamiento de 5 pulg. yde15tejas pulg.en patrón de desplazamiento deAplicación de pulg. tejas en patrón de desplazamiento de 5ypulg. pulg. pulg. 15y 15pulg.
9 9 Valley Construction: Open Valley Lay a 36" wide valley liner of Owens Corning WeatherLock® underlayment or equivalent. A 36" wide minimum 50-lb. smooth surface roll roofing can also be used as a valley liner. Fasten on outer edges only a minimum of 6" away from centerline on each side of valley. See Fig. 9. ™ Recommended valley flashing is 24" wide 26-gauge galvanized metal or an equivalent corrosion-resistant, nonstaining material.
Fig. 9A 9 Open Valley Construction Closed-Cut Valley See Fig. 9B. Construcción con canal descubierto A closed-cut valley can be used as an alternative and is applied as Valley centerline Chalk lines diverge follows: Línea de centro de canal Fig. 9B Closed-Cut Valley Construction Construcción con canal de corte cerrado Keep nails 6" from valley center Mantenga los clavos 6 pulg.
Fig. 10 Step Flashing: Use 5" x 6" corrosion-resistant metal where roof planes butt against vertical sidewalls or chimneys. See Fig. 10. Step Flashing Revestimiento escalonado Metal flashing 5" x 6" Revestimiento metálico de 5 pulg. x 6 pulg. 2" top lap Superposición superior de 2 pulg. 6" Nail flashing to roof Clavar revestimiento al techo 10 Revestimiento escalonado: Utilice metal resistente a la corrosión de 5 pulg. x 6 pulg.
Owens Corning Roofing and asphalt, LLC one owens corning parkway toledo, ohio, usa 43659 1- 800 - GET- PINK® www.owenscorning.com/roofing Pub. No. 59547-F. Printed in U.S.A. August 2014. THE Pink Panther™ & © 1964–2014 Metro-Goldwyn-Mayer Studios Inc. The color PINK is a registered trademark of Owens Corning. © 2014 Owens Corning. All Rights Reserved.
