Installation Instructions

ManualsBrandsOwens Corning ManualsBuilding materialsWoodcrest® Hip and Ridge Shingles (20 lin ft)

Before You Begin

Complete shingle application on roof deck

before applying hip and ridge shingles. Hip

shingles must be applied before applying ridge

shingles. All hip and ridge shingles are applied

with an 8 inch exposure. Note: If a new roof

is being applied over an existing roof, remove

the old hip and ridge shingles to obtain a level

application.

Handling

Use extra care in handling shingles when the

temperature is below 40°F. In cold weather, it is

recommended to warm DURARIDGE

™

shingles

before installing.

Fastener Requirement

Use galvanized steel, stainless steel, or aluminum

nails minimum 12 gauge shank with

⁄8" diameter

head. Owens Corning Roong recommends

that fasteners comply with ASTM F 1667.

Check local building codes. All Fasteners must

penetrate at least ¾" into the wood deck or

completely through sheathing.

Note: Owens Corning Roong recommends

the use of nails as the preferred method of

attaching shingles to wood decking or other

nailable surface.

Installing

Begin hip application at the eave working

toward the ridge.

1. Begin ridge application opposite the prevailing

wind direction. (Fig. A)

2. Arrange DURARIDGE

™

Hip & Ridge shingles

along the center line so that both halves of the

laminated piece fall on opposite sides of the

hip or ridge. (Fig. B)

3. Begin application by creating a starting piece

using the laminated piece with the 8 inch

exposed portion of the shingle removed.

Fasten starter piece with one nail on each

side 1 inch in from the side edge starting from

the xed side edge placed into the SureNail

Technology fastening area.

4. Continue to fasten each full shingle through

the top laminated piece with one nail on each

side placed 9 inches back from the exposed

end and 1 inch in from the side edge starting

from the xed edge of each shingle. Note:

Fasteners must be placed into the SureNail

Technology fastening area. (Fig. B)

5. Apply remaining hip and ridge shingles in the

same manner with 8 inch exposure.

6. When nishing the ridge, leave no laminated

portion of the last hip and ridge shingle

exposed. One option is to use the 8 inch

exposure portion of a hip and ridge shingle,

cutting a piece the appropriate length to

extend over the laminated portion of the

shingle to the end of the ridge.

7. Fasten nal piece with two nails, each 1 inch

in from each side edge and 1 inch in from the

end of the ridge. Cover exposed fasteners

with asphalt roof cement. Asphalt roof

cement must meet ASTM D-4586 Type I

or Type II (Asbestos Free). Note: Please be

aware that excessive amounts of asphalt roof

cement could blister the shingle.

Product Specications

Size 12 inches x 10 ¾ inches

(305 mm x 273 mm)

Pieces per Box 30

Application Exposure 8 inches (203 mm)

Lineal Coverage per Box 20 feet (6.49 m)

• STORE IN COVERED, VENTILATED AREA

(UNDER 110F/43C)

• DO NOT STACK OVER EIGHT BUNDLES

HIGH PER PALLET

• AVOID OUTSIDE STORAGE WHEN

TEMPERATURES EXCEED 90F/32C

• DO NOT STORE IN DIRECT SUNLIGHT

FAILURE TO FOLLOW THESE

STORAGE INSTRUCTIONS COULD

CAUSE SHINGLES TO STICK

TOGETHER.

Owens COrning rOOfing and asphalt, llC

ONE OWENS CORNING PARKWAY

TOLEDO, OHIO, USA 43659

1-800-GET-PINK

www.owenscorning.com/roofing

Pub. No. 10018909 -A. Printed in U.S. A. July 2014. THE PINK PANTHER

™

& ©19 64 –

DuraRidge

™

Hip & Ridge Shingles

Installation Instructions

Prepared roong is exempt from OSHA Right-

To-Know standard under its provision for

articles (29 CFR 1910.1200-b-6-IV) as dened

in 29 CFR 1910.1200c

*Limited Lifetime Warranty

This product carries a limited lifetime warranty (for

as long as you own your home). You may obtain a

copy of this roong warranty by visiting our website

at www.owenscorning.com or call 1-800-GET-PINK

(1-800-438-7465)

Owens Corning Roong and Asphalt, LLC shall not

be responsible for any damage, loss, cost, expense or

liability relating to failure to follow these instructions.

Failure to follow these installation instructions may

affect Owens Corning Roong and Asphalt, LLC's

obligations under this product's limited warranty.

10-YEAR ALGAE-RESISTANCE

LIMITED WARRANTY**

**Tropic zones outside of the USA and Canada

have a reduced algae resistance limited warranty.

See international warranty for more details.

Fig. A

8˝ Exposure

Nails

Clavos

Prevailing Wind Direction

Dirección del viento predominante

Exposición de 8 pulg.

Top View

Vista superior

Nail

Clavo

8˝

12˝

Centerline

Línea central

SureNailOwens Corning

Fig. B

Summary of content (2 pages)

PAGE 1
DuraRidge™ Hip & Ridge Shingles Installation Instructions 4. Continue to fasten each full shingle through the top laminated piece with one nail on each side placed 9 inches back from the exposed end and 1 inch in from the side edge starting from the fixed edge of each shingle. Note: Fasteners must be placed into the SureNail® Technology fastening area. (Fig. B) 5. Apply remaining hip and ridge shingles in the same manner with 8 inch exposure. 6.
PAGE 2
DuraRidge™ Hip & Ridge Shingles Instrucciones de instalación Uso Tenga mucho cuidado al usar y colocar las tejas cuando la temperatura esté por debajo de los 40°F. Cuando las temperaturas son bajas, se recomienda calentar las tejas DURARIDGE™ antes de la aplicación. Requisito de sujetador Use clavos de acero galvanizado, acero inoxidable o de aluminio, de calibre 12 como mínimo, con un diámetro de cabeza de 3/8 pulg. Owens Corning Roofing recomienda que los sujetadores cumplan con la norma ASTM F 1667.