User Manual

ManualsBrandsOutback Power ManualsInverter AccessoryOutback Power GSLC Empty

> 90% (blinks if charge parameters are met)

Color

Red

Yellow

Green

≥ 80%

≥ 70%

≥ 60%

≥ 60% off, < 60% solid, < 50% blinks

Battery State-of-Cha rge

FN DC LED Indica tors

Compone nts

900-0153-01-00 Rev A.vsd\Page-1\ 2013-01-17

MAT E3 Programming

IMPORT ANT :

Programming should be done by a qualified installer who is trained on programming inverter power systems. Failure to program accurate parameters for the

system could potentially cause equipment damage. Damage caused by inaccurate programming is not covered by the limited warranty for the system.

Conta ct Te chnic al Support:

Telephone: +1.360.618.4363

Email: Support@outbackpower.com

Website: www.outbackpower.com

IMPORTAN T :

Not intended for use with

life support equipment.

AC Source

Utility Grid, or

AC Generator

Main Electrical Panel

(or overcurrent device for

the AC source)

Electrical Distribution Subpanel

(Load Panel)

Battery Bank

Photovoltaic (PV) Array

(with PV Combiner Box [PV8 or PV12])

Cust ome r-Supplie d Com ponents

Charge Controller

FLEXmax 80*

FLEXmax 60*

Optiona l OutBa c k Compone nts

PV Combiner Box

PV8

PV12

*Including appropriate Mounting Bracket.

Inverter/Charger

GS Load Center

System Display

and Controller

MATE3 (FW-MB3

mounting bracket)

Communications

Manager

HUB10

HUB 4

GS8048

FLEXnet DC Monitor (FNDC)

Surge Protector

Remote Temperature Sensor (RTS)

Ra dia n Syst e m Produc t s

Ma jor Components

GSLC175-PV-120/240

Communication

Mana ger

(H U B10)

MAT E3

System

Display and

Cont roller

GS8048 I nve rte r/Charger

GS Loa d Ce nter

(GSLC)

FLEX max 80

Cha rge Cont rolle rs

(x2 ) (Opt iona l)

RADIAN Series

Not e: For automatic generator

start features see the MATE3

manual for details.

Summary of content (4 pages)

PAGE 1
M AT E3 Progra m m ing Com pone nt s RADIAN Series I M PORT AN T : Programming should be done by a qualified installer who is trained on programming inverter power systems. Failure to program accurate parameters for the system could potentially cause equipment damage. Damage caused by inaccurate programming is not covered by the limited warranty for the system.
PAGE 2
Wire Size s/T orque Re quire m e nt s M ount ing RADIAN Series 1 4 AC Terminals - Inverter DC Terminals - Inverter AC Circuit Breakers DC Circuit Breakers 5 GFDI 6 7 PV Circuit Breakers Mechanical Interlock (Bypass) 8 9 2 3 WARN I N G: Fire /Ex plosion H a za rd GS8 0 4 8 Do not place combustible or flammable materials within 12 feet (3.7 m) of the equipment. This unit employs mechanical relays and is not ignition-protected. Fumes or spills from flammable materials could be ignited by sparks.
PAGE 3
Ene rgize /St a rt up Proc e dure s De -e ne rgize /Shut dow n Proc e dure s Pre -st a rt up Proc e dure s: Func t iona l T e st Point s Func t iona l T e st Point s Battery Voltage Test Points Battery Voltage Test Points 1. Double-check all wiring connections. 2. Inspect the enclosure to ensure no tools or debris has been left inside. 1a 3. Disconnect all AC loads at the backup (or critical) load panel. 4. Disconnect the AC input feed to the GSLC at the source.
PAGE 4
Ge ne ra l Wiring RADIAN Series Ra dia n I nve rt e r/Cha rge r AC LEGEN D Neutral I M PORT AN T : Example only. Actual wiring may vary depending on local electric code. Factory wiring is not shown.