Quick Start Guide
14.0"
(35.6 cm)
12.0"
(31.8 cm)
Bottom
Screws
Plywood
(Optional)
Wall Board
Wall
Bracket
Wall Stud
N
E
U
L1 L2
GRID
L1 L2
GEN
N
E
U
N
E
U
L1 L2
OUT
RELAY
AUX
+ -
12V
AUX
Switch
INV
Remote
Battery
Temp
ON/OFF
INV
28.0"
(71.1 cm)
16" (40.6 cm)
0.5" (1.3 cm)0.5" (1.3 cm)
29.1"
(74.0 cm)
45.0"
(114.3
cm)
13.7"
(34.8 cm)
Inverter
Bracket
8.75"
(22 cm)
For GSLC door
clearance, space
systems 0.9"
(3.2 cm) apart.
When
stacking
multiple
inverters:
Installation
7
5
6
1
3
4
16" (40.6 cm)
Plywood (Optional)
Wall Board
Wall
Stud
Wall Bracket
Wall
Stud
4.1"
(10.4 cm)
5.0"
(12.7 cm)
6.0" (15.2
cm)
8.0" (20.3
cm)
2
Keyhole Slots
To install the GSLC, unscrew the inverter bottom screws approximately ¼”
(0.6 cm) to 3/16" (0.5 cm).
Align the GSLC along the bottom of the inverter. Slide the bottom screws
into the keyhole slots.
Mark the spots for the GSLC mounting feet. (If necessary, remove the
GSLC to install wall anchors.) Install screws to secure the feet.
Follow the appropriate instructions for installing other components.
Different mounting locations are available.
5
6
7
8
Tools Required
o Wrench and socket sets; should include
torque and ratchet wrenches
reversible (stubby) wrenches for narrow access
offset box wrench, ½" or 13 mm
o Wire cutters/strippers
o Insulated screwdriver set (flat and Phillips);
should incl
ude
#2 Phillips screwdriver 15 to 16" long
o Long-nose pliers
o High-resolution voltmeter
Ensure the mounting surface is strong enough to handle 3 times the total
weight of all the components. Add plywood or other reinforcing material as
necessary to strengthen the surface.
Attach the wall bracket. Center the mounting holes on the wall studs. Use all
6 mounting screws to secure the bracket.
Lift the inverter so that the inverter bracket is above the wall bracket.
Lower the inverter so that the inverter bracket slips into the wall bracket.
1
3
4
2
BEFORE STARTING
o This product is for indoor use only
o These instructions generally assume the use of OutBack
produ
cts from the front page; instructions may differ if not used
o If GSLC is not used, make certain all electrical connections
meet
local safety standards and codes
Materials In Box
o Inverter
o Mounting Bracket
o Hardware Kit
o Quick Start Guide
(
this document)
o RTS
(Remote Te
mperature Sensor)
The FLEXmax charge controller
is mounted with brackets. Two
controllers can be mounted side
by side with larger brackets
(using the forward holes to allow
for conduit).
The Radian has two sets of
bracket positions. The GSLC
has one set.
NOTE: The FLEXmax 100
charge controller attaches
directly to the wall, not the
Radian system.
The Radian allows two locations for the
system display mounting bracket.
The Radian has one
mounting location for
the HUB product.
The GSLC also has
one location.
Left Side: Right Side:
8
900-0162-01-01 REV A Sheet 1 of 3
©2017 OutBack Power Technologies. All Rights Reserved.