Quick Start Guide

ManualsBrandsOutback Power ManualsDisconnectOutback Power Flexware ICS Plus DC 6 String Combiner Box FWPV6-FH600-SDA

Quick Start Guide

900-0175-01-00 REV C.vsd

FLEXware ICS

Features:

 Powder-coated aluminum housing

 Stainless steel hardware

 Low-profile design

 Mounting methods: vertical wall, pole, or sloped

roof mount to 14° incline (3 in 12 pitch)

 Padlock hole for up to 3/8" shank

 Models FWPV6-FH600 & FWPV4-FH600 include

fuse holders

NOTE:

Fuses must be UL listed, 1 to 20 Adc, rated minimum 600 Vdc

Packs of (10) replacement 15 Adc or 20 Adc fuses are available

from OutBack dealers. They are sold under OutBack part numbers

FUSE-15-600Vdc/10 or FUSE-20-600Vdc/10.

Models:

 FWPV4-FH600

o (4) 600-Vdc fuse holders, DIN rail, distribution blocks,

ground terminal bus bar (TBB), and one cable gland

with (9) sealed holes for up to 7.7 mm wire

 FWPV6-FH600

o (6) 600-Vdc fuse holders, DIN rail, distribution blocks,

ground terminal bus bar (TBB), and two cable glands

with (9) and (5) sealed holes for up to 7.7 mm wire

 FWPV6

o DIN rail, distribution blocks, ground terminal bus bar

(TBB), and one cable gland with (9) sealed holes for

up to 7.7 mm wire

NOTES:

 The DIN rail holds up to (6) 600 Vdc fuse holders (Cooper

Bussman model CHPV1U). These are available from OutBack

dealers under OutBack part number FH-30-1000Vdc-DIN.

 A second, 5-hole cable gland must be installed when

installing more than (4) input PV circuits. The 5-hole

gland is available from OutBack dealers under OutBack

part number CABLEGLAND-5.

 Replacement 9-hole glands are sold under OutBack

part number SPARE-301.

 Use only UL listed wet location or raintight conduit hubs

for entry into the enclosure.

Integrated Combiner Solution

Padlock HoleCover

Securing

Screw

Removable

Cover

FWPV4-FH600 FWPV6-FH600

FWPV6

Distribution

Block

Fuse

Holders

Distribution

Block

DIN Rail

Pre-Integrated

Wires

DIN Rail

Cable

Gland

Cable

Glands

Mounting

Knockouts

(6x)

Ground TBBGround TBB

Ground TBB

Cable Gland

Conduit Knockouts

(1½" Trade Size)

Conduit Knockouts

(1½" Trade Size)

Conduit Knockouts

(1½" Trade Size)

Mounting

Knockouts

(6x)

Mounting

Knockouts

(6x)

Listings:

 UL1741

 CSA22.2

Certifications:

 CE (IEC 62109-1)

Environmental Ratings:

 Ingress Protection: IP44 and NEMA 3R

 Environmental Category: Outdoor

 Wet Locations Classification: Yes

 Pollution Degree Classification: PD 3

 Ambient Temperature: 60°C

 Relative Humidity (RH) Rating:

5% to 95% noncondensing

 Maximum Altitude Rating: 6561' (2000 m)

 Overvoltage Category (PV Input):

OV Cat II

NOTE: The DC input circuits are isolated from

the enclosure.

If system grounding is required by Section 250 of

the NEC (ANSI/NFPA 70), it is the responsibility of

the installer.

IMPORTANT:

 If this product is installed or used in a manner

other than specified, the protection it provides

may be impaired.

 Fuses are not to exceed maximum output rating.

0.83"

(2.1 cm)

8.0"

(20.3 cm)

8.25" (21.0 cm)

3.0"

(7.6 cm)

6.0" (15.2 cm)

3.75"

(9.5 cm)

11.5"

(29.2 cm)

Summary of content (2 pages)

PAGE 1
Quick Start Guide Integrated Combiner Solution Listings: FLEXware ICS Features:  UL1741  CSA22.2  Powder-coated aluminum housing Certifications:  Stainless steel hardware 8.0" (20.3 cm)  Low-profile design  CE (IEC 62109-1) 11.5" (29.
PAGE 2
Wiring: Save These Instructions Integrated Combiner Solution Torque Requirements Distribution Block Input Terminals Output Terminals Cable Size* Fuse Holder Terminals 2/0 to #1 AWG (70 to 50 mm2) -- -- 100 in-lb (11.4 Nm) -- #2 AWG (35 mm2) -- 80 in-lb (9 Nm) 80 in-lb (9 Nm) -- 2 Ground TBB #4 to #6 AWG (25 to 16 mm ) 30 in-lb (3.4 Nm) 80 in-lb (9 Nm) 80 in-lb (9 Nm) 35 in-lb (3.9 Nm) #8 AWG (10 mm2) 30 in-lb (3.4 Nm) 35 in-lb (3.9 Nm) 35 in-lb (3.9 Nm) 25 in-lb (2.