OutBack Power GS7048E / GS3548E Quick Start Guide with GSLC

ManualsBrandsOutBack Power Systems ManualsBalance of SystemOutBack Power Prewired 300VDC GSLC

Masters of the Off-Grid.™

First Choice for the New Grid.

900-0159-01-00 Rev B.vsd\Page-1\2014-01-30

Setup and Programming

Note: See the MATE3

manual for details on

generator control.

Quick Start Guide RADIAN Series

HUB 10.3

Communications

Manager

MATE3

System

Display and

Controller

Radian Inverter/Charger

GS Load Center

(GSLC)

FM80 Charge

Controllers

(x2)

WARNING: Fire/Explosion Hazard

Do not place combustible or flammable materials within 3.7 m (12 feet) of

the equipment. This unit employs mechanical relays and is not ignition-

protected. Fumes or spills from flammable materials could be ignited by sparks.

WARNING: Personal Injury

Use safe lifting techniques and standard safety equipment when working with

this equipment.

IMPORTANT:

Clearance and access requirements may vary by location. Maintaining a 90-cm

(36") clear space in front of the system for access is recommended.

Consult local electric code to confirm clearance and access requirements

for the specific location.

CAUTION: Equipment Damage

These procedures should be done by a qualified installer who is trained on programming inverter power systems.

Failure to set accurate parameters for the system could potentially cause equipment damage. Damage caused by

inaccurate programming is not covered by the limited warranty for the system.

IMPORTANT

Check the firmware revision of all OutBack devices before use. The Radian inverter and MATE3 system display may not

communicate or operate correctly unless their firmware is above a specified revision number.

For model GS7048E, the firmware must be revision 001.005.xxx or higher with a MATE3 revision of 002.010.xxx or higher.

For model GS3548E, the firmware must be revision 001.005.xxx or higher with a MATE3 revision of 002.017.xxx or higher.

The MATE3 Configuration

Wizard allows quick setup of

parameters that apply to all

systems. The Configuration

Wizard is reached from the

MATE3 Main Menu as shown

to the right.

The firmware revision of all

devices can be confirmed by

navigating from the MATE3

Main Menu as shown below.

Upgrades to the firmware

revision can be downloaded

from the OutBack website

www.outbackpower.com.

IMPORTANT:

Not intended for use with

life support equipment.

Contact Technical Support:

Telephone: +1.360.618.4363

Email: Support@outbackpower.com

Website: www.outbackpower.com

AC Source

Utility Grid or

AC Generator

Main Electrical Panel (or overcurrent

device for the AC source)

Electrical Distribution Subpanel

(Load Panel)

Photovoltaic (PV) Array

Battery Bank

Customer-Supplied Components

Optional OutBack Components

FLEXnet DC Monitor (FN-DC)

Remote Temperature Sensor (RTS)

Charge Controller

FLEXmax 80 depicted

(with FW-CCB2

mounting bracket)

PV Combiner Box PV12 depicted

Communications

Manager

HUB10.3 depicted

EnergyCell depicted

Inverter/Charger

GS Load Center

System Display

and Controller

MATE3 depicted

(with FW-MB3

mounting bracket)

GS7048E

GS3548E

Radian System Products

Major Components

GSLC175-PV-230

GSLC175PV1-230

(both depicted)

Firmware Revision

Configuration Wizard

Off Grid

Grid Tied Backup

This advances the display to the

Setup Complete screen.

This advances the display to the

Setup Complete screen if the

FLEXnet DC is not installed. If the

FLEXnet DC is installed, the display

advances to the Shunt screens.

If FN-DC is installed...

Generator Installed Y

Generator Type AC Size 5.0 kW

Generator Start Manual

AUX Output Device Port 1

Back Continue

New Configuration >>

Existing Configuration >>

Restore Configuration >>

System Type Grid Tied

System Voltage 48 VDC

Array Wattage 1000

Battery Type FLA Capacity 500 Ah

Back Continue

Absorb Voltage 57.6 VDC Time 1.0

Float Voltage 54.4 VDC Time 1.0

Equalize Voltage 60.0 VDC Time 3.0

Re-Float Voltage 44.0 VDC

Back Continue

New Configuration Initialized

Back Continue

Shunt A

Connection Inverter

Back Continue

Shunt B

Connection Charge Controller

Back Continue

Shunt C

Connection Charge Controller

Back Continue

Period 1 Enable N

Weekday Use 0:00 Drop 0:00

Weekend Use 0:00 Drop 0:00

Back Continue

Period 2 Enable N

Weekday Use 0:00 Drop 0:00

Back Continue

Period 3 Enable N

Weekday Use 0:00 Drop 0:00

Back Continue

Shunt A

Connection Inverter

Back Continue

Shunt B

Connection Charge Controller

Back Continue

Shunt C

Connection Charge Controller

Back Continue

Mode Disabled

Grid Connect 48.0 VDC Delay 60 Min

Grid Disconnect 52.0 VDC Delay 60 Min

Grid Connect SOC 60% Disconnect SOC 95%

Back Continue

Shunt B

Connection Charge Controller

Back Continue

Shunt C

Connection Charge Controller

Back Continue

Period 3 Enable N

Weekday Use 0:00 Drop 0:00

Back Continue

Mode Disabled

Grid Connect 48.0 VDC Delay 60 Min

Grid Disconnect 52.0 VDC Delay 60 Min

Grid Connect SOC 60% Disconnect SOC 95%

Back Continue

Period 1 Enable N

Weekday Use 0:00 Drop 0:00

Weekend Use 0:00 Drop 0:00

Back Continue

Generator Installed N

Generator Type AC Size 5.0 kW

Generator Start Manual

AUX Output Device Port 1

Back Continue

AC Output Voltage 230 VAC

AC Phase Single

AC Input Breaker Size 50 A

Maximum Output Load 30 A

Back Continue

Period 2 Enable N

Weekday Use 0:00 Drop 0:00

Back Continue

Generator Installed N

Generator Type AC Size 5.0 kW

Generator Start Manual

AUX Output Device Port 1

Back Continue

Absorb Voltage 57.6 VDC Time 1.0

Float Voltage 54.4 VDC Time 1.0

Equalize Voltage 60.0 VDC Time 3.0

Re-Float Voltage 44.0 VDC

Back Continue

AC Output Voltage 230 VAC

AC Phase Single

AC Input Breaker Size 50 A

Maximum Output Load 30 A

Back Continue

System Type Backup

System Voltage 48 VDC

Array Wattage 1000

Battery Type FLA Capacity 500 Ah

Back Continue

Shunt A

Connection Inverter

Back Continue

AC Output Voltage 230 VAC

AC Phase Single

AC Input Breaker Size 50 A

Maximum Output Load 30 A

Back Continue

Absorb Voltage 57.6 VDC Time 1.0

Float Voltage 54.4 VDC Time 1.0

Equalize Voltage 60.0 VDC Time 3.0

Re-Float Voltage 44.0 VDC

Back Continue

System Type Off Grid

System Voltage 48 VDC

Array Wattage 1000

Battery Type FLA Capacity 500 Ah

Back Continue

Settings >>

Configuration Wizard >>

Device Data Logs >>

Event Logs >>

Firmware Update >>

System >>

Inverter >>

Charge Controller >>

Battery Monitor >>

MATE3 >>

System

System Information >>

Save / Store Information >>

Firmware Version >>

Date and Time >>

LCD Display >>

MATE3 002.017.018

1: GS7048E 001.005.002

2: GS7048E 001.005.002

Settings >>

Configuration Wizard >>

Device Data Logs >>

Event Logs >>

Firmware Update >>

Settings

Configuration Wizard

New Configuration

Summary of content (4 pages)

PAGE 1
Quick Start Guide Setup and Programming ! RADIAN Series CAUTION: Equipment Damage Major Components WARNING: Fire/Explosion Hazard These procedures should be done by a qualified installer who is trained on programming inverter power systems. Failure to set accurate parameters for the system could potentially cause equipment damage. Damage caused by inaccurate programming is not covered by the limited warranty for the system. Do not place combustible or flammable materials within 3.
PAGE 2
Installation 1 RADIAN Series 2 Ensure the mounting surface is strong enough to handle 3 times the total weight of all the components. Add plywood or other reinforcing material as necessary to strengthen the surface. Attach the wall bracket. Center the mounting holes on the wall studs. Use all 6 mounting screws to secure the bracket. 1 3 Lift the inverter so that the inverter bracket is above the wall bracket. 4 Lower the inverter so that the inverter bracket slips into the wall bracket.
PAGE 3
Energize/Startup Procedures ! De-energize/Shutdown Procedures CAUTION: Fire Hazard RADIAN Series Functional Test Points Functional Test Points Before energizing, confirm that all hardware is installed as shown on the Installation page. Stacking battery terminal hardware in any other order can overheat the terminals. Battery Voltage Test Points 1a Battery Voltage Test Points 1a 1b 1c 1b 1c 1d 1d PV Voltage Test Points PV Voltage Test Points Pre-startup Procedures: 1.
PAGE 4
Wiring RADIAN Series AC Distribution Panel FLEXnet DC L1 Twisted-pair wiring Neutral Utility Grid 1 (+) Positive Battery 2 (–) Negative Sense 3 Relay Connections (not shown) 4 5 (–) Bus Bar Shunt C 6 (–) FM-80 #2 7 (–) Bus Bar Shunt B 8 (–) FM-80 #1 9 (–) Bus Bar Shunt A 10 (–) Inverter N Inverter Circuit AC Source Ground GS7048E multiple inverters (stacking) GS3548E wiring With GSLC175PV1-230 and grid bypass To ports as shown below with GSLC175-PV-230; PV and FLEXnet DC not shown To ports as