Safety Instructions

CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with your new OttLite
®
product.
WARNING: To prevent electric shock, make sure the lamp is not plugged in until
all steps are complete.
NOTE: THIS UNIT IS FULLY ASSEMBLED
1.
Remove the lamp from the packaging and place on a flat surface.
2.
Connect power adapter input (A) into connector (B) in the rear-bottom of the lamp.
3.
Plug the power adapter (E) into a standard household 120V AC outlet. Note:
Only use with the supplied power adapter to avoid damage or fire.
4.
Power switch (F) is a “touch” switch that controls ON/OFF power, the LED
brightness settings and the colour mode function of the lamp.
5.
Touch button (F) to turn the lamp ON/OFF and adjust the brightness.
6.
Touching and holding button (F) will change the colour mode. This lamp
provides three colour modes 5000°K, 4000°K, 2700°K.
7.
To position the shade simply bend the flex-neck as needed to point the light.
Please hold the lamp base while adjusting the lamp.
WIRELESS CHARGING INSTRUCTIONS:
Wireless charging requires a Qi-certified device. To determine if your device is
Qi-certified, please visit the Wireless Power Consortium website.
To wirelessly charge a device, perform the following:
• Place the device, which supports Qi wireless charging standard, face up on the
middle of the Qi wireless charging emblem (C). NOTE: Phone will charge in either
vertical or horizontal position.
• A red indicator light (G) will come on to indicate charging.
• Check the charge level on your device periodically to determine when device is
fully charged. NOTE: Lamp DOES NOT provide any indication of when device is
fully charged.
CAUTION!
DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL
AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE.
USB CHARGING PORT
THIS LAMP CONTAINS a 5V, 2,1A USB output port (D) located on the bottom rear
of lamp. USB port can charge items such as tablets, cellular phones, etc.
SAFETY WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS
1.
Turn lamp off and WAIT UNTIL LAMP HEAD IS COOL before handling.
2.
The LED panel might get hot after several hours of continuous use DO NOT
place your hands directly on LED light panel.
3.
Never use with an extension cord unless the plug can be fully inserted into the
receptacles in the extension cord.
4.
Do not alter the plug.
5.
The lamp head included with this unit cannot be replaced by the consumer.
6.
INDOOR USE ONLY.
NOTE: The important safety instructions appearing in this instruction sheet are not
meant to cover all possible conditions and situations that may occur. It must be
understood that common sense, caution, and care must be used with any electrical
product.
CAUTION!
IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS
DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE
AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.
CAUTION!
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN
THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
CAUTION:
ENGLISH Wireless Charging LED Desk Lamp with Phone Stand
A
C
G
Wireless Charging LED Desk Lamp with Phone Stand
CSNQC00Z-CA CSNQCG5Z-CA 9569000 X9FS
INS200572 REV051220
B
D
F
E
• Connect the equipment into an o
utlet on a circuit different from that to which the
receiver is connected.
POWER ADAPT
ER SPECIFICATION:
Input: AC 100-2
40V, 50/60 Hz, 1.2A Max
Output: 12V DC
, 2.5A with a Male DC Plug
The “Qi”
symbol is a tr
ademark of the Wireless Powe
r Consortium
Qi CHAR
GER SPECIFIC
ATION:
Output:
up to 5 Watts depending on de
vice
• Consult the dealer or an experie
nced radio/TV technician for help.
Changes or modifications not ex
pressly approved by the party responsible for
compliance could void the user’
s authority to operate the equipment.
This device complies with Part 1
5 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause
harmful interference, and
(2) this device must accept a
ny interference received, including interference that
may cause undesired ope
ration.
FCC/IC RF RAD
IATION EXPOSURE STATEMENT
CAUTION:
To maintain com
pliance with the FCC’s RF exposu
re guidelines, place the product
at least
20cm from nearb
y persons.
IC CANA
DA
This device contains licence-exempt transmitter
(s)/receiver that comply with
Innovation, Scie
nce and Economic Development
Canada’s licence-exempt RSS
(s).
Operation is sub
ject to the following two conditi
ons:
1. This device m
ay not cause interference.
2. This device m
ust accept any interference, inc
luding interference that may ca
use
undesired operation of the device.
Any change or
modification to product not ex
pressly recognized by
OttLite Technol
ogies voids OttLite’s responsib
ility for proper function of prod
uct.
CAN RSS-216/CNR-216
CAN ICES-005 (B)/NMB-005 (B)