Safety Instructions

ManualsBrandsOttlite Technologies ManualsElectrical EquipmentLED table lamp

CONGRATULATIONS! You’ve purchased the ﬁnest in natural lighting technology

with your new OttLite

product.

PRODUCT REGISTRATION FORM

Please complete the enclosed Product Registration Form and return it today by mail

, or

WARNING: To prevent electric shock, make sure the lamp is not plugged in until

all steps are complete.

NOTE: THIS UNIT IS FULLY ASSEMBLED

Remove lamp from packing, placing lamp body base (A) ﬂat on a steady surface.

Connect power adapter input (B) into connector (C) in the rear-bottom of the lamp.

3. Plug the power adapter (D) into a standard household 120V AC outlet. Note:

Only use with the supplied power adapter to avoid damage or ﬁre.

4. Turn the lamp ON/OFF by using power switch (E) located on top of shade (F).

To power LED settings, slightly touch switch (E) to achieve the following:

• Turn lamp “ON” to 1st brightness setting; touch the switch “once”;

• for 2nd brightness setting; touch the switch “two-times”;

• for 3rd brightness setting; touch the switch “three-times”;

• to turn lamp “OFF”; touch the switch “four-times”.

6. Touch button (G) to turn night light on/off.

7. Wireless charger for Qi-certiﬁed devices (H) is located in the center of base (A).

See

Wireless Charging Instructions

section for details.

8. To reposition the light, hold the lamp base (A) steady and grasp either ﬂex-neck

(J) or shade (F) depending on needed adjustment. DO NOT FORCE the shade

or lamp body outside allowable adjustable range as excessive adjustment may

cause damage.

WIRELESS CHARGING INSTRUCTIONS:

Wireless charging requires a Qi-certiﬁed device. To determine if your device is

Qi-certiﬁed, please visit the Wireless Power Consortium website.

To wirelessly charge a device, perform the following:

• Place the device, which supports Qi wireless charging standard, face up on the

middle of the Qi wireless charging icon (H).

• When the device is centered on the Qi wireless charging icon (H), a solid RED

light (K) will indicate the device is charging properly. NOTE: If RED light is

blinking or is not illuminated, this indicates the device is not charging and needs to

be properly centered.

• Check the charge level on your device periodically to determine when device is

fully charged. NOTE: Product DOES NOT provide any indication of when device is

fully charged.

CAUTION!

DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL

AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE.

SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS

1. Turn lamp off and WAIT UNTIL LAMP HEAD IS COOL before handling.

2. The LED panel (L) might get hot after several hours of continuous use DO NOT

place your hands directly on LED light panel.

3. Never use with an extension cord unless the plug can be fully inserted into the

receptacles in the extension cord.

4. Do not alter the plug.

5. The lamp head included with this unit cannot be replaced by the consumer.

6. INDOOR USE ONLY.

NOTE: The important safety instructions appearing in this instruction sheet are not

meant to cover all possible conditions and situations that may occur. It must be

understood that common sense, caution, and care must be used with any electrical

product.

CAUTION!

IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS

DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE

AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.

CAUTION!

THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN

THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.

CAUTION: Any change or modiﬁcation to product not expressly recognized by

OttLite Technologies voids OttLite’s responsibility for proper function of product.

FCC PART 15

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that the interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION:

To maintain compliance with the FCC’s RF exposure guidelines, place the product at least

20cm from nearby persons.

To maintain compliance with the IC RF exposure guidelines,place the product at least

10cm from nearby persons.

IC CANADA

This device contains licence-exempt transmitter(s)/receiver that comply with Innovation,

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject

to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause

undesired operation of the device.

CAN RSS-216/CNR-216

CAN ICES-005 (B)/NMB-005 (B)

POWER ADAPTER SPECIFICATION:

Input: AC 100-240V, 50/60 Hz, 0.4A

Output: 12V DC, 1A with a Male DC Plug

Qi CHARGER SPECIFICATION:

Output: up to 5 watts depending on device

The “Qi” symbol is a trademark of the Wireless Power Consortium

ENGLISH Inspire LED Desk Lamp with Wireless Charging

Inspire LED Desk Lamp with Wireless Charging

CS3QN4WW K7FS

INS220698 REV040522

Summary of content (2 pages)

PAGE 1
ENGLISH Inspire LED Desk Lamp with Wireless Charging CONGRATULATIONS! You’ve purchased the finest in natural lighting technology with your new OttLite® product. PRODUCT REGISTRATION FORM Please complete the enclosed Product Registration Form and return it today by mail, or register online by going to: OttLite.com/warranty WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete. L NOTE: THIS UNIT IS FULLY ASSEMBLED J 1.
PAGE 2
FRANÇAIS Lampe de bureau à DEL Inspire avec chargement sans fil FÉLICITATIONS! Vous avez fait l’achat de la meilleure technologie en éclairage naturel avec votre produit OttLite® FORMULAIRE D’ENREGISTREMENT DE PRODUIT Compléter le formulaire d’enregistrement qui est inclus pour votre produit et nous le retourner dès aujourd’hui par le retour du courrier ou enregistrez-vous en ligne en visitant le : OttLite.com/warranty J E REMARQUE : CET ARTICLE EST COMPLÈTEMENT ASSEMBLÉ 1.