INSTRUCTIONS FOR USE Amigo eZync
Contents IMPORTANT NOTICE Please familiarise yourself with the entire contents of this booklet before using your Amigo eZync. The booklet contains various statements, safety instructions and important information about the use and handling of the Amigo eZync.
Introduction Typical package content Congratulations on your decision to take the next step in improving classroom FM. Amigo eZync belongs to the Amigo FM product family from Oticon – a company that strives to provide superior solutions for school and home use. The Amigo family is extremely versatile, making life much easier for users in academic, professional and social listening situations. With Amigo eZync, channel management in educational surroundings have become even more manageable.
Preparing the Amigo eZync Powering the Amigo eZync To power the Amigo eZync, plug in the power supply (see picture) and connect it to the wall outlet. The Amigo eZync has a battery back-up that will last for up to 48 hours. It will automatically switch to battery power when the mains power is disconnected, and vice versa. Power jack LED indicator The back-up battery may take several hours to charge when the Amigo eZync is powered for the first time.
Where to place the Amigo eZync The Amigo eZync has a synchronisation range of approximately 1.5 metres. To ensure that the synchronisation commands actually reach the Amigo ear-level receivers, it is important to position the unit optimally. The best location is close to the door or in the corridor just outside the classroom. Then you can be absolutely certain that all receivers will be continuously synchronised and on the right channel.
Mounting the Amigo eZync on a wall The optimal position for this unit is 1.5 metre above the floor, next to the entrance (see page 11). 1. Use the wall mount as a guide to mark the location of the holes. 2. Drill the two holes in the wall. 3. If necessary, insert anchors inside the drilled holes. 4. Insert fasteners through the washer and wall mount. 5. Gently tighten the until the wall mount is secure. Avoiding bending the wall mount. 1.
Placing the Amigo eZync on a shelf When the wall mount has been installed, plug the power supply into the jack on the Amigo eZync. The Amigo eZync can then slide onto the wall mount: 1. Align the Amigo eZync with the wall mount. 2. Once the Amigo eZync is hanging on the wall mount, slide the unit to the left to lock it in place. 3. To remove the Amigo eZync, lift it a little and slide it to the right. If If you occasionally need to move the Amigo eZync, use the stand that is supplied with the Amigo eZync.
LED legend Choosing and changing channels The LED on the Amigo eZync does more than indicate that the power is on. It shows: The channel on the Amigo eZync can be changed by synchronising it with an Amigo T20/ T21/WRP. To change the transmitting channel on the Amigo T20/T21/WRP transmitter, press and hold either the S button or the T button for two seconds to select one of the predefined lists of channels.
Synchronising the Amigo eZync Synchronising other manufacturers’ receivers The Amigo eZync can be synchronised in the first 60 seconds after it has been turned on. With the Amigo eZync you have the possibility to synchronise Amigo ear-level receivers and Widex ear-level receivers. Within a distance of approximately 50 cm, press the SYNC button on the Amigo T20/T21/WRP. If the synchronisation is successful, the LED on the Amigo eZync will blink three times. Visit www.oticon.
Cleaning the Amigo eZync Appendix A: Troubleshooting The Amigo eZync is moisture repellent, making it very easy to clean with a damp cloth. Problem Solution The LED is not lit Check that the power cable is connected properly. Check that the Amigo eZync is turned on. The LED is blinking The Amigo eZync is running on battery back-up. Check that the power cable is connected properly.
Appendix B: Manufacturers’ warranty The manufacturer, Oticon, issues a one-year limited warranty to the original consumer of this product. This warranty comes into effect upon the date of original purchase of this equipment, and will remain in effect for one calendar year from that date. Please note that extended warranties may apply in your country. Please contact your local hearing care professional for more information.
The manufacturer reserves the right to make changes in the design or construction of any of its instruments at any time without incurring any obligation to make any changes whatsoever on units previously purchased. This warranty is in lieu of all other expressed warranties by the manufacturer. No representative or person is authorised to represent or assume for the manufacturer any liability in connection with the sale or use of this product other than as set forth above.
The Amigo eZync contains a radio transmitter with: ID: U28EZYNC01 IC: 1350B-EZYNC01 Warnings The Amigo eZync is not a toy and therefore should be kept out of the reach of children and anyone else who might swallow parts or otherwise cause injury to themselves. Special attention should be paid to the smaller components in order to prevent children from swallowing them and choking. The device complies with Part 15 of the FCC rules and RSS-210 of Industry Canada.
Never expose the Amigo eZync to excessive heat by putting it in the oven, microwave oven or burning it. There is a risk that it will explode and cause serious injury. Date of purchase: 908 67 210 00 / 11.08 Amigo serial numbers: The Amigo eZync complies with the most stringent standards of International Electromagnetic Compatibility. However, the unit may cause interference with other medical devices, such as defibrillators and pacemakers.
