User Manual

ManualsBrandsOTC ManualsAutomotiveHub Grappler Hydraulic Kit

Sheet No.

Issue Date: Rev. C February 20, 2013

Form No. 562717

Parts List and

Operating Instructions

for: 6575-3

Hydraulic Hub Grappler™ Kit

655 EISENHOWER DRIVE

OWATONNA, MN 55060-0995 USA

PHONE: (507) 455-7000

TECH. SERV.: (800) 533-6127

FAX: (800) 955-8329

ORDER ENTRY: (800) 533-6127

FAX: (800) 283-8665

INTERNATIONAL SALES: (507) 455-7223

FAX: (507) 455-7063

1 of 3

Explanation of Safety Signal Words

The safety signal word designates the degree or level of hazard seriousness.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not

avoided, may result in property damage.

Added translations at last revision

to this document.

Summary of content (6 pages)

PAGE 1
655 EISENHOWER DRIVE OWATONNA, MN 55060-0995 USA PHONE: (507) 455-7000 TECH. SERV.: (800) 533-6127 FAX: (800) 955-8329 ORDER ENTRY: (800) 533-6127 FAX: (800) 283-8665 INTERNATIONAL SALES: (507) 455-7223 FAX: (507) 455-7063 Form No. 562717 Parts List and Operating Instructions for: 6575-3 Hydraulic Hub Grappler™ Kit Explanation of Safety Signal Words The safety signal word designates the degree or level of hazard seriousness.
PAGE 2
Parts List and Operating Instructions Form No. 562717, Sheet 1 of 3, Back Safety Precautions WARNING: To prevent personal injury and/ or equipment damage, • • • • • • • • Study, understand, and follow all safety precautions and operating instructions before using this hydraulic Hub Grappler™ kit. If the operator cannot read instructions, operating instructions and safety precautions must be read and discussed in the operator’s native language.
PAGE 3
Parts List and Operating Instructions Form No. 562717 Parts List 1 2 3 9 8 4 7 5 6 Item No. Part No. 1 308343 2 No. Req'd Description 1 Carrying Case 2510A 1 Air/Hydraulic Pump 3 544744 1 Hose – 1.83 M (6 foot) - 6.35 mm (.25 in.) NPT 4 10676 1 Straight Fitting 5 22301 1 Hex Nut – .75-16 UNF (Grade 8) 6 314194 1 Forcing Screw 7 544745 1 6.35 mm (.25 in.) Hose Half Coupler (Male) 8 544788 1 6.35 mm (.25 in.
PAGE 4
Parts List and Operating Instructions Form No. 562717, Sheet 2 of 3, Back Instructions This kit is to be used with the 6575 Hub Grappler™ Kit to add hydraulic function to removing and installing half shaft driven wheel bearings. It is not necessary to remove the knuckle assembly from the vehicle, and, as a result, wheel alignment is not altered. Vehicle Setup Raise the vehicle until all weight is off the wheels and they hang freely. 1.
PAGE 5
Parts List and Operating Instructions Form No. 562717 Front or Rear Hub Removal Cylinder 1. Lubricate the forcing screw from this kit, assemble components, and attach Hub Grappler to hub as shown in Figure 4. 523410 Nut 22301 2. Align all components and tighten forcing screw nut to hold components for a straight pull. 3. Operate the pump to extend the cylinder piston just far enough to pull the the hub assembly. Forcing Screw 314194 311881 Adapter Figure 4 Bearing Removal 1.
PAGE 6
Parts List and Operating Instructions Form No. 562717, Sheet 3 of 3, Back Bearing Installation New Bearing NOTE: The bearing installer must be assembled with the flat side toward the bearing and the small diameter pilot away from the bearing. 1. Lightly lubricate the new bearing, and position it for installation with the tool components assembled as shown in Figure 7 for outboard installation or Figure 8 for inboard installation. 2.