OSS-KIT-EXP-6002 Host Server to Expansion System Kit User Manual SKU: OSS-KIT-EXP-6002 www.onestopsystems.
One Stop Systems Table of Contents 1 Overview .......................................................................................................................................................................... 3 1.1 Description .................................................................................................................................................................................................... 3 1.2 1.3 2 3 Features ...................................................
One Stop Systems 1 Overview 1.1 Description The PCIe x4 expansion kit is used to extend the PCI express bus from a host server to an external expansion chassis. The host adapter card inserts into a PCIe slot of the server. It then cables to a downstream expansion link board (ELB). The ELB acts as a downstream cable link board and the primary fan-out switch to support multiple configurations of PCI express expansion slots. The host adapter installs into a PCIe x4, x8 or x16 slot on the host motherboard.
One Stop Systems 1.2 Features 1.1.1 1.1.2 Adapter Cards The Host adapter card inserts into any PCI Express x4, x8, 16 slot on the host motherboard. The Target adapter card fits into SHN slot of PICMG 1.3 backplane.. Support half-height bracket. The Host and Target cable adapter cards require no software / drivers x4 Link Cable Available in 1m, 2m, 3m, 5m, 7m lengths. PCI-SIG Express Cable Specification Compliant.
One Stop Systems 1.3 Specifications 1.3.1 Host Adapter PCIe x4 Host Cable Adapter Card (SKU : OSS-PCIe-HIB25-X4-H) Form Factor Dimension (H x L) Front Panel Connectors Front Panel Indicators Red-drivers Temperature Range Relative Humidity Shock Vibration Power Consumption Agency Compliance Redriver 1.3.2 PCIe x4 add-in card 2.7” x 3.
One Stop Systems 1.3.3 PCIe x4 Cable PCIe x4 Cable (SKU : OSS-PCIe-CBL-x4.1M) 1 meter long cable Cable Length Circuits loaded Gender Lock to Mating Part Material-Metal Pitch-Mating Interface Single Ended Water proof / Dust proof Wire Insulator Diameter Wire Size AWG Wire / Cable Type Electrical Current Shielded Voltage-Maximum OSS-KIT-EXP-6002| 6 1m, 2m, 3m, 5m, 7m 38 Male-to-Male Yes Zinc Alloy 0.80mm (0.
One Stop Systems 2 Component Identification 2.1 Host cable adapter card The PCIe x4 expansion kit contains two cable adapter boards, the host cable adapter and the target cable adapter. The host adapter inserts into the host computer’s PCIe x4, x8 or x16 slot. Cable LED indicators are the same for both Host and Target configurations. 2.2 Expansion Link Board The Expansion Link Board (ELB) OSS-CPCIe3-3U/6U-ELB-x4 is a downstream link board that installs into a CPCIe chassis.
One Stop Systems 3 Installation Instructions 3.1 Installing the Adapter Kit 1. Insert the host cable adapter into an appropriate PCIe slot of the host computer. For example, a PCIe x4 host board can be inserted into a PCIe x16, x8, or x4 slot. It will still operate at x4 speeds. Secure the cable adapter card 3.2 Expansion link board 1. 2. Insert the expansion link board into the SHB slot on the chosen backplane. Connect the x4 PCIe cable to both cables adapter cards.
One Stop Systems 4 Technical Information The transmit and receive signals on the OSS-HIB-25x4 are driven and conditioned by Pericom redriver chips. Adjustments can be made to equalization, de-emphasis and output swing. These controls are factory set by the use of zero Ohm resistors. In the following tables, a 0 indicates that a zero Ohm resistor has been installed and a 1 indicates no resistor.
One Stop Systems 4.3 Pin-out for the PCIe x4 Card Edge Connector on the “Host Cable Adapter” Side B Side A Pin # Name Description Name Description 1 2 3 4 5 6 7 8 9 10 11 N/C N/C N/C GND NC N/C GND +3.3V N/C 3.3Vaux N/C N/C N/C N/C Ground N/C N/C Ground 3.3 V power Not connected 3.3 V auxiliary power N/C PRSNT1# N/C N/C GND N/C JTAG3 JTAG4 N/C N/C +3.3V PERST# Hot-Plug presence detect N/C N/C Ground Not connected TDI (Test Data Input) TDO (Test Data Output) Not connected Not connected 3.
One Stop Systems 4. Board side pin-outs on both sides of the Link are identical. The cable assembly incorporates a null modem for the PCIe transmit and receive pairs. 4.4 PCI Express x4 Connector PIN Assignment 4.
One Stop Systems 4.6 Signal Descriptions PETp(x) PCI Express Transmit Positive signal of (x) pair. PETn(x) PCI Express Transmit Negative signal of (x) pair. PERp(x) PCI Express Receive Positive signal of (x) pair. PERn(x) PCI Express Receive Negative signal of (x) pair. CREFCLK+/- Cable REFerence CLocK: Provides a reference clock from the host system to the remote system. SB_RTN Side Band ReTurN: return path for single ended signals from remote systems.
One Stop Systems B17 B18 B18 PWR_RTN CWAKE# CPERST# Power management signal for wakeup events (optional) Cable Reset# 4.
One Stop Systems 5 Contacting Technical Support Our support department can be by phone at 1 (760) 745-9883. Support is available Monday through Friday, 8:00 AM to 5:00 PM PT.
One Stop Systems ass ONE STOP SYSTEMS 2235 Enterprise Street, Suite#llO, Escondido CA 92029 Toll-Free (800) 285-8990 US• Main (858) 530-2511 • Fax (858) 530-2733 www.onestopsystems.
