Daim Ntawv Qhia Tus Neeg Siv
Table Of Contents
One
Stop
Systems
Support:
www.onestopsystems.com/support-0
Toll
Free:
+1
(877)438-2724
Local:
+1
(760)745-9883
WARNING
Electrostatic
Discharge
(ESD)
Warning
Electrostatic
Discharge
(ESD)
is
the
enemy
of
semiconductor
devices.
You
should
always
take
precautions
to
eliminate
any
electrostatic
charge
from
your
body
and
clothing
before
touching
any
semiconductor
device
or
card
by
using
an
electrostatic
wrist
strap
and/or
rubber
mat.
FCC
Statement
NOTE:
Ellis
equipment
has
been
tested
and
found
to
comply
with
the
limits
for
a
Class
A
digital
device,
pursuant
to
part
15
of
the
FCC
Rules.
These
limits
are
designed
to
provide
reasonable
protection
against
harmful
interference
when
the
equipment
is
operated
in
a
commercial
environment.
This
equipment
generates,
uses,
and
can
radiate
radio
frequency
energy
and,
if
not
installed
and
used
in
accordance
with
the
instruction
manual,
may
cause
harmful
interference
to
radio
communications.
Operation
of
this
equip
-
ment
in
a
residential
area
is
likely
to
cause
harmful
interference
in
which
case
the
user
will
be
required
to
correct
the
interference
at
his
own
expense.
Changes
or
modifications
not
expressly
approved
by
the
party
responsible
for
compliance
could
void
the
user's
authority
to
operate
the
equipment
This
device
complies
with
Part
15
of
the
FCC
Rules.
Operation
is
subject
to
the
following
two
conditions:
(1)
this
device
may
not
cause
harmful
interference,
and
(2)
this
device
must
accept
any
interference
received
including
interference
that
may
cause
undesired
op
4UV
UNIT
&
370
HIB
CARDS
4UV
EXPANSION
SYSTEM
Quick
Start
Guide
Need
More
Help?
Download
the
User
Manual
at
www.onestopsystems.com
Industry
Canada
This
Class
A
digital
apparatus
complies
with
Canadian
ICES-003.
Cet
appareil
numériqué
de
la
classe
A
est
conformé
à
la
norme
NMB-003
du
Canada
CE
The
product(s)
described
in
this
manual
complies
with
all
applicable
European
Union
(CE)
directives.
One
Stop
Systems
will
not
retest
or
recertify
systems
or
components
that
have
been
reconfigured
by
customers
eration.
Connect the other end of the cable to the Host card. If you have
another host card, plugin the other end of the cable to the 2nd
Host card.
One Stop Systems |
www.onestopsystems.com
Toll Free: (877)438-2724 Local: + 1(760)-745-9883
Set Host Card to Host mode x16
Install Host Card
1
2
Connect Ipass Cables To Host Card
Connect Power Cables
Power Supply and Front LEDs
7
Verify Host and Target Card Link LEDs
8
Unit is Ready
Check dipswitches are set to Host mode. Refer to User’s manual
for details on the switch setting.
Turn Off computer. Plug in the card in x16 slot. Plugin the second
host card (applicable to 4UV-10 Slot and 16 Slot units).
Connect all available power cables / cords to the power supplies.
Upon powering up the host, the expansion unit will instantly
power Up. The two power supply LEDs and the two front LEDs
will illuminate as solid green.
Verify and check that there is a stable link between Host and
Target cards. Both cards will illuminate the following LEDs:
CBL, EDG & PWR.
Connect Ipass Cables to Target Card
3
Connect the x16 Ipass cable to Target . If you have 4UV-10 or 16
slot units, plugin the second Ipass cable to the second target card.
4
5
Power UP Computer
6
Connect power cable (s) to computer. Press the power button to
power up.
9
The unit is now ready to use.
To install your PCIe card, please shutdown the expansion
unit and computer completely.
Disconnect power cables from the expansion unit.
Plug in your preferred PCIe cards in the downstream slots
and secure it.
Reconnect power cables to expansion unit.
Turn ON the computer. The expansion unit will power UP.
Please refer to the manual for more details.
x16 PCIe Slots
Front Panel LEDs