Technical Specifications

ManualsBrandsOSI ManualsPaint16 fl. oz. QUAD Window and Door Installation Foam

OSI® QUAD® Foam

Window & Door Installation Foam

Page 1 of 4

Description: OSI QUAD Foam Window & Door Installation Foam is a single component, minimal

expansion and low pressure polyurethane foam packaged in a pressurized metal container. It is specifically

designed for use with the OSI QUAD Window & Door System. It is dispensed in bead form for sealing

gaps and cracks, holes and voids around windows and doors, in most types of construction projects. The

product exhibits slight to moderate expansion during application and cures upon reaction with moisture to

form a flexible, urethane foam. The closed cell structure of this material provides an R factor of 5 per inch

of cured foam making it an efficient method for stopping air and moisture infiltration and expensive warm

and cold air loss between windows and rough frame. OSI QUAD Foam will not warp or deform windows

and doors. OSI QUAD Foam adheres to all types of building materials including wood, concrete, and

drywall and is compatible with asphalt and butyl flexible flashing. It complies with all Federal and State

VOC regulations.

Available As:

Item #

Size

Color

1866185

21.1 fl oz (598g)

Tan

Features & Benefits:

 Low Foam Pressure/Low Expansion: Will Not Warp or Deform Windows and Doors

 Quick Setting Formulation: Can Be Cut or Trimmed in Less Than 1 Hour

 Cold Temperature Application (14°F)

 Insulation Value of R5/Inch

 Closed Cell Structure Does Not Absorb Moisture

 Flexible/Will Not Crack or Dry Out

Recommended For:

OSI QUAD Foam is part of the OSI QUAD Window & Door System and is used to insulate and seal around windows and door

frames. It can also be used for jambs, mud sills, header joints, corner joints, top plate penetrations, electrical and plumbing

penetrations and other areas where air infiltration or heat loss may occur. Bonds most building materials including vinyl,

aluminum, fiberglass, wood, OSB, PVC, concrete and metal.

For Best Results:

 OSI QUAD Foam is not a fire stopping material and SHOULD NOT be used in areas that require fireproof or fire stopping

materials

 Urethane foams are adversely affected by sunlight (UV light). Exposed foam must be coated with a protective covering or

coating

 Do not store product on its side

 Does not bond to polyethylene, polytetrafluoroethylene (PTFE)/Teflon® or siliconized surfaces

 For cold weather applications, product should be stored above 41°F (5° C) at least 12 hours before application

Coverage:

For a 21.1 oz can:

 A 1/2” (12.7 mm) bead size will deliver approximately 409 ft. (99 m) of foam

Please note: Yields shown are based on theoretical calculations, for comparison purposes, and will vary depending on ambient

conditions and particular application.

Summary of content (4 pages)

PAGE 1
Description: OSI QUAD Foam Window & Door Installation Foam is a single component, minimal expansion and low pressure polyurethane foam packaged in a pressurized metal container. It is specifically designed for use with the OSI QUAD Window & Door System. It is dispensed in bead form for sealing gaps and cracks, holes and voids around windows and doors, in most types of construction projects.
PAGE 2
Typical Uncured Physical Properties: Color: Tan Appearance: Minimal expansion foam Base: Single component polyurethane Odor: Ether-like Specific Gravity: 1.107 Flash Point: < 0°F (-18°C) % Solids by Weight: 70% VOC Content: <1.
PAGE 3
Directions: Tools Typically Required: OSI Foam Gun (IDH #1413066), OSI Foam Clean (IDH # 1427512), and utility knife. Painter’s tape for protecting surfaces. Safety Precautions: Always wear eye protection, gloves and proper work clothes when using OSI QUAD Foam. Wash hands after use. Cured foam is difficult to remove from skin, clothing and other substrates. It may discolor skin. Preparation: Read all operating instructions packaged with the dispensing unit before using.
PAGE 4
until all vapors are gone. DO NOT SMOKE. Extinguish all ignition sources. If burned, dried foam may release hazardous decomposition products. Dried foam may be combustible if exposed to flame or temperatures above 240°F. CONTENTS UNDER PRESSURE. Avoid prolonged exposure to sunlight or heat from radiators, stoves, hot water and other heat sources that may cause bursting. Do not puncture, incinerate, burn or store above 120°F. Do not discard empty can in garbage compactor. VAPOR AND SPRAY MIST HARMFUL.