Installation & Assembly_1

Package Contents
1of2
Assembly Instruction Sheet #IS-PCCD1613C
For Style PCCD1613C
Crossbar
Assembly
x1
A
Fixture Body
x1
B
D
E
C
Crystal String A
x4
STEP 1 Attach Crossbar Assembly to Outlet Box-
A. Attach the Crossbar Assembly (E) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the Mounting Holes
on the Outlet Box. Tighten until snug.
Figure 1
2016 QuoizelInc.
ReleasedDate:2016-08-15
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
Outlet
Box
E
Outlet Box Screw
(not supplied)
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
(4)G9BaseClearXenonBulbs40WMaximum.
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Crystal String B
x8
Crystal String C
x4
STEP 2 Test Fitting Fixture Body to Crossbar Assembly-
A. Remove mounting balls from the Crossbar Assembly (E). Fit the
Outlet Box
E
Mounting
Screw
Mounting Ball
D
Figure 2
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into the outlet box and position the Fixture
Body (D) over the outlet box. Align the holes in the Fixture Body (D)
with mounting screws. Attach Fixture Body (D) by using mounting
balls. Hand tighten until snug.
Outlet Box
E
Mounting Screw
Mounting Ball
D
Figure 4
Lock Screw
and Hex Nut
(Step 2 Continued)
Fixture Body (D) to the Crossbar Assembly (E) and secure with
mounting balls. Note: The Fixture Body (D) should be snug against
the ceiling and the mounting balls. If not, adjust the length of the
mounting screw on the Crossbar Assembly (E) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the Crossbar Assembly (E) until the
correct length is achieved. Once the Fixture Body (D) is secure,
remove the mounting ball and Fixture Body (D) and proceed to
Step 3.
Clear G9
Xenon Bulb
x4
F