TM Baby Monitor Secure 700 User Guide
TABLE OF CONTENTS WARNINGS AND SAFETY INFORMATION 1 Getting Started 3 Your Baby Monitor 5 Basic Operation 8 Troubleshooting 11 Product Specifications 12 Guarantee 13
Safety Information 1 Safety Information Please read this operating instruction manual thoroughly. Intended use The surveillance system has been developed to monitor rooms. The baby unit sends acoustic and video signals from its point of installation to the parent unit. Any other use is considered unintended use. The use of this equipment does not substitute personal supervision, e.g. of a child. Users are not relieved of their personal liability.
2 Safety Information Rechargeable batteries ATTENTION ! Never throw batteries into a fire. Only use batteries of the same type! Pay attention to correct polarity. Power failure In the event of a power failure, the devices only operate through battery power. Disconnect the power adapter plugs from the devices in this case. Medical equipment ATTENTION ! Never use the devices in the vicinity of medical equipment. Effects on such equipment cannot be fully ruled out.
Getting to Know your SC700 2 Getting to know your SC700 The buttons in this operating manual are subsequently depicted with a uniform contour. Therefore, slight deviations in the appearance of the symbols on the buttons compared to those depicted here are possible.
4 Getting to Know your SC700 Camera unit (baby Unit) 23 18 19 22 21 27 24 20 25 26 28 26 18 19 20 21 22 23 24 25 26 27 28 Night light Light sensor Power LED Microphone Lens Antenna Loudspeaker Temperature sensor Socket for power adapter plug ON/OFF switch Battery compartment
Using your SC700 3 Installation Operating with batteries (not supplied) Safety information ATTENTION ! It is essential to read the Safety Information in Chapter 1 before using your SC700. Checking the package contents One monitor unit (parent unit) with belt clip/support One power One charger with adapter plug for power adapter plug The baby unit for the parent unit Use a small screwdriver to open the baby Insert the batteries, paying attention to correct polarity.
6 PACK CONTENTS Connecting the parent unit ATTENTION ! Position the parent with a minimum distance of 1 m to other electronic devices, otherwise there is a risk. The parent unit is powered by a 3.6 V, 930 mAh battery pack. The rechargeable battery pack can be recharged directly in the parent unit when it is inserted in the charging station. The Power LED lights up red when the parent unit is being charged. In the case of a low battery charge, the Power LED flashes slowly.
Operating the baby Unit 4 Operating the baby Unit Check the baby unit and parent unit are working properly each time before the equipment is put into operation. Switching the baby unit on/off Position the baby unit in a good position for the monitoring tasks required and align the camera lens to the area to be monitored. Slide the switch to ON. The Power LED lights up green. The baby unit is now ready to operate. To switch the unit off, slide the switch to OFF.
8 Operating the Parent Unit 5 Operating the Parent Unit Check the baby unit and parent unit are working properly each time before the equipment is put into operation. Switching the parent unit on/off Press and hold this button until you hear 2 acoustic signals. The logo appears first then the image being taken by the baby unit camera. Press and hold the button for approx. 1 second to switch the unit off. In the case of a low battery charge, the Power LED flashes slowly. Press this button twice.
PACK CONTENTS 1 or a button on the parent unit is pressed. VOX: Voice Operated Transmission = Sound detection Registration Selecting a lullaby Press the button on the right hand side of the parent unit. This icon appears in the display. Use the button to select one of the 5 lullabies (1-5). If no number is displayed, all of the lullabies will continue to play in sucession until deactivated. Use this button to adjust the volume to one of five settings.
10 Fault Finding 6 Customer Support Should you experience difficulties operating the SC700 please refer to the problems and solutions guide below. If you still experience difficulties please contact Oricom Customer Support on 1300 889 785 for assistance. Problems and solutions Problems Equipment does not function No reception Reception interference Solutions − Baby unit and/or parent unit are not switched on. − The batteries are empty or defective. − The power adapter plugs are not connected.
Technical Specifications 11 7 Technical Specifications Technical data Feature Camera (baby unit) Monitor (parent unit) Power supply (parent unit) Initial charging time for battery Power supply (baby unit) Range Value Socket: 6 V DC Sensor: 1 night light sensor IR diodes: 8 Screen: 2,4" LC display Socket: 6 V DC Power adapter plug, input: 100-240 VAC, 50-60Hz, 150 mA Power adapter plug, output: 6 VDC, 800 mA or rechargeable battery NiMH 3.
12 Guarantee Warranty (Australia) (a) Warranty Oricom International Pty Ltd (Oricom) warrants that the product is free from defects in materials and workmanship for a period of 12 months effective from the date of purchase. This warranty in no way affects your statutory warranty under the Trade Practices Act 1974 or any other similar legislation.
Australia Customer Support Oricom International Pty Ltd Locked Bag 658 South Windsor, NSW 2756 Email: support@oricom.com.au Web: www.oricom.com.au Phone: 1300 889 785 Fax: +61 2 4574 8898 New Zealand Customer Support Baby First Limited Email: admin@babyfirst.co.nz Web: www.babyfirst.co.
