Baby Monitor Secure 300 User Guide
TABLE OF CONTENTS WARNINGS AND SAFETY INFORMATION 1 GETTING STARTED 3 YOUR BABY MONITOR 6 BASIC OPERATION 10 TROUBLESHOOTING 15 PRODUCT SPECIFICATIONS 16 GUARANTEE 17
WARNINGS AND SAFETY INFORMATION IMPORTANT 1 Do not place the cord in a high "wear and tear" location. Never use a frayed or compromised cord. Please read this user guide thoroughly before use. Your ORICOM Baby Monitor is designed to be an aid and should not be used as a substitute for responsible and proper adult supervision of a child.
2 WARNINGS AND SAFETY INFORMATION Battery requirements Each parent unit requires two rechargeable Ni-MH batteries, size AA 1.2V 1300mAh. • Do not dispose of the batteries in a fire, as they can explode. • Do not open, unscrew or temper with any of your baby monitor units or battery. Always carry out repairs through your authorised ORICOM representative or other duly qualified tradesperson. • Released electrolyte from the battery is corrosive and can cause damage to the eyes or skin.
GETTING STARTED Thank you for choosing this monitor from Oricom. Installation and Charger Your Secure 300 Baby Monitor offers the best Digital Technology. For the Parent Unit INTERFERENCE FREE FREQUENCY DECT (Digital Enhanced Cordless Telecommunications) is the most widely used worldwide digital cordless technology, offering amazingly clear sound, long range and maximum voice security. DECT operates on the 1.
4 GETTING STARTED 4 Press [ ] to turn the Parent Unit on. • Before first use, or if it has been out of use for a long time, the Parent Unit will need to be charged for 14 hours. During this time, the Parent Unit will operate from the Charger pod when switched on. Note that the Parent Unit cannot be used without batteries, even if it is placed in the charger. For the Baby Unit 1 In event of a power failure, your Baby Monitor can switch to battery power.
GETTING STARTED Wall mounting the Baby Unit Use the following wall mount diagram to locate and install the mounting pins/screws if you prefer to wall mount your base unit. The dimensions are shown in millimeters (mm). 58.00 Ø 4.00 5 Ø 7.5 5 1. Insert screws into the wall through the wall mount. The recommended mounting screw size is diameter 3mm and length 20mm,the diameter of the screw head and the screw should not be greater than 7.55mm and 4mm respectively. 2.
6 YOUR BABY MONITOR Baby unit (Sender) Night light Press to switch night light on or off. Brightness Press to adjust the night light brightness (once night light is switched on). There are three levels. Page Press to page the Parent unit – useful for finding when it is misplaced. Power on/off Press to switch on or off. Microphone Link light Green when linked to Parent unit. Flashes if not linked - first 30 seconds. Flashes when Talk is pressed on Parent unit.
YOUR BABY MONITOR 7 Back of Baby unit Underside Power socket For connection to mains power. Battery lock Child tamper proof lock for the battery compartment.
8 YOUR BABY MONITOR Parent unit From the Parent unit you can listen to your baby and operate the Baby unit by remote control. Talk (on side of unit) Press to talk to your baby. Lullaby LEDs Green on - When the selected lullably is being played. Up Increase speaker volume. Increase sensitivity when reviewing the setting. Change lullaby when playing. Mute LED Green on – When speaker is muted. Mute Press to switch the speaker off, press again to switch it back on.
YOUR BABY MONITOR Parent unit charger Front Back Charging light Indicates Parent unit is charging. Power socket For connection to mains power.
10 BASIC OPERATION Once you have set up your Baby Monitor, you will be able to hear the sounds in your baby’s room through the Parent Unit. And also see the green and red sensor lights around the top of the Parent Unit rise and fall with the sound levels.
BASIC OPERATION 11 • If the volume of the Parent Unit is turned off, an alert will sound when the audio picked up reaches the second red led. Note: Do not position the baby unit and the parent unit close to each other or in the same room as feedback may be generated. You can press [Mute] key to temporarily turn off the speaker. Press [Mute] key again to turn on the speaker. Sensitivity You can adjust the sensitivity on the Parent Unit to monitor the sound from the Baby Unit.
12 BASIC OPERATION Talk Back • Press [Page] key on the Baby Unit. The paging alert will sound. You can use the talk back feature to talk to your baby. • To stop the Page alert, press any button on the Parent Unit, or press [Page] key again on the Baby Unit. • Press and hold [Talk] key on the Parent unit to speak to baby. The green link lights on both Units flash. • Talk into parent unit's microphone. • Release [Talk] key to hear your baby again.
BASIC OPERATION 13 Lullaby Out of Range The Baby unit plays lullabies to gently soothe your baby back to sleep. Each lullaby is played repeatedly for 15 minutes. Select one of the three melodies or select Play All for a medley of all 3 lullabies for 15 minutes. The Lullaby LEDs indicate which lullaby is playing or if all 3 are being played. When the baby and parent units have no link with each other (eg. Out of range, parent unit or Baby unit is not powered on), the green Link light flashes.
14 BASIC OPERATION Note: Low battery alert can be suppresed by pressing any button. Charging the Battery Place the parent unit on its charger pod to charge the battery. When charging, the red light on the charger will light steadily. The Low Battery light will be turned off. Note: The Parent Unit must never be operated on the charger pod without batteries. The parent unit can be used on or off the charger pod. When on charger pod, the batteries will be recharged at the same time.
TROUBLESHOOTING 15 Problem Possible cause(s) The red power lights do not turn on when you 1. Check if the units are properly connected to the power supply. plug in the power. 2. Check if the power is turned on. If not, Press [ ] to turn on the power. The green Link light on the Parent Unit is flashing and cannot hear the sounds from your baby's room. 1. You may have moved out of range. Move closer to the Baby Unit and wait 5 seconds for the Link to establish. 2.
16 PRODUCT SPECIFICATIONS Feature Specifications Operating Frequency 1.8 GHz Range Up to 300 m under optimum conditions. The range is reduced in buildings (up to 50 m) as a result of walls, doors etc. Power supply (parent unit / baby unit) Input: 100 - 240 VAC 50 - 60 Hz Output: 7.5 VDC, 500 mA, Non rechargeable batteries (baby unit) (not included in the package contents) Type: AA, 1.
GUARANTEE 17 Warranty (Australia) (a) Warranty Oricom International Pty Ltd (Oricom) warrants that the product is free from defects in materials and workmanship for a period of 12 months effective from the date of purchase. This warranty in no way affects your statutory warranty under the Trade Practices Act 1974 or any other similar legislation.
Australia Customer Support Oricom International Pty Ltd Locked Bag 658 South Windsor, NSW 2756 Email: support@oricom.com.au Web: www.oricom.com.
