Baby Monitor Secure 200 User Guide
TABLE OF CONTENTS WARNINGS AND SAFETY INFORMATION 1 Getting Started 3 Your Baby Monitor 5 LCD Display of Baby Monitor 8 Basic Operation 9 Menu Settings 14 Troubleshooting 19 Product Specifications 20 Guarantee 21
WARNINGS AND SAFETY INFORMATION IMPORTANT Please read this user guide thoroughly before use. Your ORICOM Baby Monitor is designed to be an aid and should not be used as a substitute for responsible and proper adult supervision of a child. The Baby Monitor has been designed to provide some added reassurance in the form of sound transmission for those times when you are not in the same room as your baby provided you always stay within hearing range of the baby monitor during use.
2 WARNINGS AND SAFETY INFORMATION • Do not dispose of the battery in a fire, as they can explode. Cleaning and care • Do not open, unscrew or tamper with any part of this product. Should your product go faulty; contact Oricom Support 1300 889 785 or 02 4574 8888. The surface of the case can be cleaned with a dry, soft, lint-free cloth. Never use cleaning agents, particularly aggressive solvents. Apart from occasional cleaning of the case, no other care is necessary.
Getting Started Thank you for choosing this monitor from Oricom. Your Secure 200 Baby Monitor offers the best Digital Technology. INTERFERENCE FREE FREQUENCY DECT (Digital Enhanced Cordless Telecommunications) is the most widely used worldwide digital cordless technology, offering amazingly clear sound, long range and maximum voice security. DECT operates on the 1.
4 Getting Started 6. Press [ ] to turn the Parent Unit on. • Before first use, or if it has been out of use for a long time, the Parent Unit will need to be charged for 16 hours before use. After this time, the Parent Unit will operate from the Charger pod when switched on. Note that the Parent Unit cannot be used without a battery pack, even if it is placed in the charger pod. For the Baby Unit 1. In event of a power failure, your Baby Monitor can switch to battery power.
Your Baby Monitor 5 Baby unit (Sender) 1 Temperature Sensor Picks up the temperature in your baby's room. 2 Battery Cover For non rechargeable batteries (not supplied). 3 Night light key Press to turn On the night light. Press again to turn Off the light. 4 Power On/Off Key Press to turn ON the Baby unit. Press and hold to turn OFF. 5 Page key Press and hold for 2 seconds to Page the Parent Unit with an audible alert. Useful to call for assistance or to locate a missing Parent Unit.
6 Your Baby Monitor Left view of baby unit Parent unit (Receiver) 11 DC 6V input Connecting to Power Adaptor. 12 Battery Cover Rechargeable battery pack. 13 Belt Clip 14 Volume Up/Down Keys Adjust the volume at which you hear the sounds in your Baby's room, and scroll through the menu during setting. 15 Power On/Off Key Press to turn the parent unit ON. Press and hold to turn OFF.
Your Baby Monitor 16 Menu key, [OK] key Press to adjust the features of your Baby Monitor. Press [ ] key to enter the menu options, use [ / ] keys to scroll through the menu choices and [OK] key to select. Press [ ] key to exit. 17 Link Light Green light ON indicates "Linked" to Baby Unit. Flashing light indicates "Link" is lost. 18 Display Indicates the current settings of your Baby Monitor, including: Battery level, Date and Time, Temperature, Lullaby on/off, Lullaby melody.
8 LCD Display of Baby Monitor Baby Unit Parent Unit 1. Battery level indicator 1. Sensitivity indicator 2. Numbers/Characters indicator 2. Night light indicator 3. Temperature indicator 3. Battery level indicator 4. Lullaby on/off indicator 4. Numbers/Characters indicator 5. Temperature indicator 6. Feed time Alarm indicator 7.
Basic Operation Once you have set up your Baby Monitor, you will be able to hear the sounds in your baby's room through the Parent Unit. And also see the green and red sensor lights around the top of the Parent Unit rise and fall with the sound levels.
10 Basic Operation Baby alert! Night light You can set your Parent Unit to give an extra warning "beep" when the noise levels in your baby's room is high and the red lights on the sound sensor are lit. This is particularly useful if the volume of your Parent Unit is turned down and you are just using the sensor lights to monitor the noise levels in your baby's room.
Basic Operation 11 2. Press [ ] key to scroll to the different lullabies, or to select [Play all?]. 3. Press [ ] key again to start or stop the lullaby. On the Parent Unit 1. Press [ ] key, then use [ / ] keys to scroll to "Lullaby". Press [ OK ] key. 2. "Play?" is shown on the display. Use [ / ] keys to scroll to "Select New". Press [ OK ] key. 3. The Display shows the current lullaby. Use [ / ] keys to scroll to your choice of tune, or to "Play All". Press [ OK ] key. 4.
12 Basic Operation Talk to your Baby You can speak to your baby from the Parent Unit, perhaps to reassure them that you are on your way. Press and hold [ Parent Unit. ] key and speak into the front of the • Please note that you will not be able to hear your baby while you are speaking to them until you release [ ] key again. Customize your Baby Monitor to your Baby Some babies are louder than others! You can customize the sound sensitivity of your Baby Monitor to suit your baby.
Basic Operation 13 Charging the Battery Depending on the usage; the Parent Unit will work for up to 10 hours with a fully charged battery. If a battery low alert tone is heard and the battery icon on the Parent Unit's display is flashing, you should put the parent unit on the Charger Pod to recharge the battery. You can still use your Parent Unit from the Charger Pod. When charging, the red power light on the charger will light steadily.
14 Menu Settings Note: All Menu settings operations are only available on the Parent unit. ] key to exit. During setting, press [ Night light Setting You can turn on or off the night light on the baby unit via the parent unit. ] key on the parent unit and use [ / ] keys 1. Press [ to select "Night Light". The display is shown below: Start playing Press [ OK ] key, "Play?" is shown, press [ OK ] key to play the lullaby and "Saved" is shown on the display.
Menu Settings 15 1. Press [ ] key on the parent unit and use [ / ] keys to select "Sensitivity". The display is shown below: Set On or Off 1. Press [ OK ] key, "On?" or "Off?" is shown on the display, press [ OK ] key to select Sound Alert on or off and "Saved" will be displayed on the parent unit. Adjust Volume 2. Press [ OK ] key and then use [ / ] keys to select the sensitivity level. There are 5 levels. 3. Press [ OK ] key to confirm and "Saved" is shown on the display.
16 Menu Settings Press [ ] key on the parent unit and use [ / ] keys to select "Temperature". The display is shown below: Set desired baby room temperature range 1. Press [ OK ] key, "Set Range" is shown on the display. 2. Press [ OK ] key, use [ / ] keys to set the upper and lower temperature limits. 3. Press [ OK ] key to confirm and "Saved" is shown on the display. Set temperature alert You can turn on and off the temperature alert on the Parent Unit. 1.
Menu Settings 17 Set the time 2. Press [ OK ] key and "Set time" is shown on the display. Press [ OK ] key. 3. "Year" is shown on the display. Use [ / ] keys to select the correct year. Press [ OK ] key. 4. "Month" is shown on the display. Use [ / ] keys to select the correct month. Press [ OK ] key. 5. "Day" is shown on the display. Use [ / ] keys to select the correct day. Press [ OK ] key. 6. "Hour" is shown on the display. Use [ / ] keys to select the correct hour using the 24 hour clock.
18 Menu Settings Set the first or next feed time 1. Press [OK] key, "Set Time" is shown on the display. 2. Press [ OK ] key, then follow the procedures in the Set the time of Clock Setting to set the hour and minute. Set the interval for following feeds Language Setting The displayed information can be set in different languages. ] key and use [ / ] keys to scroll to 1. Press [ "Language". The display is shown below: 1. Press [ OK ] key and use [ / ] keys to select "Set Interval". 2.
Troubleshooting 19 Problem Possible cause(s) The red power lights do not turn on when you plug 1. C heck if the units are properly connected to the power supply. in the power. 2. C heck if the power is turned on. If not, Press [ ] to turn on the power. 1. Y ou may have moved out of range. Move closer to the Baby Unit and wait 5 The green Link light on the Parent Unit is flashing seconds for the Link to establish. and cannot hear the sounds from your baby's 2.
20 Product Specifications Feature Specifications Operating Frequency DECT 1.8 GHz Range Up to 300m under optimum conditions. The range is reduced in buildings (up to 50m) as a result of walls, doors etc. Power supply (Baby Unit) Input: 100~240 VAC 50/60Hz Output: 6 VDC, 500 mA, Non rechargeable batteries, baby unit (not included in the package contents) Type: AAA, 1.
Guarantee 21 Warranty Information (Australia) Oricom makes no other warranties or conditions, express or implied, including as to acceptable quality and fitness for a particular purpose, except as stated in this Warranty. Any implied warranties that may be imposed by law are limited in duration to the Warranty Period. Oricom warrants that the product is free from defects in materials or workmanship during the Warranty Period.
Customer Support If you have any problems setting up or using this product you will find use-full tips and information in the Troubleshooting section of this user guide as well as “Frequently Asked Questions” on our website www.oricom.com.au. If you have further questions about using the product after reviewing the resources above or would like to purchase replacement parts or accessories please call our Customer Support Team.
