In-Out Thermometer with Cable Free Sensor and Clock Model: RAR232 User Manual
USER'S MANUAL CONTENTS INTRODUCTION Introduction ............................................................... Product overview ...................................................... Main unit ................................................................. Remote unit ............................................................ Table stand and wall mounting ............................... Main unit ................................................................. Remote unit ..........................
EN 1. Three-line display Facilitates easy reading of remote and indoors temperatures and calendar clock. 2. Down ( ) button Decreases the value of a setting. 3. Up ( ) button Increases the value of a setting. 4. MODE/SET button Toggles the display modes and confirms entry while setting the values for display. 5. Memory (MEM) button Recalls the maximum or minimum temperature of main and remote unit. 6. Alarm ( ) button Displays the alarm time or sets the alarm status. 7.
EN REMOTE UNIT 1. LED indicator Flashes when the remote unit transmits a reading. FRONT BACK 2. RESET button 3. °C / °F switch Selects between degrees Centigrade (°C) and Fahrenheit (°F). 1 2 3 4. Battery compartment Accommodates 2 UM-3 (AA) 1.5V batteries. 4 5. Battery compartment cover 5 3 RAR232A-E CP5.
EN TABLE STAND AND WALL MOUNT 2. Ensure that the base of the stand fits into the 2 small holes at the bottom of the main unit. The main and remote units can either be positioned on a flat surface or mounted on a wall. 3. To remove the stand from the battery cover, press your finger against the latch in the opening found at the bottom of the stand as shown in the diagram. MAIN UNIT 4. Pull the stand out in a downward motion to release. REMOTE UNIT (WALL MOUNT) TABLE STAND 1.
EN GETTING STARTED Once batteries are in place for the remote unit, temperature readings will be transmitted at 39-second intervals. The main unit will search for signals for approximately 4 minutes after the batteries have been installed. BATTERIES 1. Remove the remote unit battery compartment cover and insert batteries. 3. Position the main unit close to the remote unit. 4. Press RESET on the remote unit. 5. Press RESET on the main unit to begin synchronization. 2. Install the main unit batteries.
EN KINETIC WAVE DISPLAY The kinetic wave display shows the signal reception status of the main unit. There are three possible outcomes: reception of temperature readings will resume once the interference recedes. Searching for signal. Signal is secure. No signals. For best results: • Place the unit away from electrical or mechanical objects. • Place the unit out of direct sunlight and moisture. • Do not place the remote unit more than 100 feet (30meters) from the main unit.
The clock and calendar share the same section of the display. The calendar is displayed in a day-month format. Press the MODE button to toggle between clock and calendar display modes. SET ALARM To set the alarm: 1. Press once to display the alarm time. If the alarm is disarmed, the time will be displayed as . 2. Press and hold for two seconds, The hour digits will blink. 3. Enter the hour by pressing either or . 4. Press . The minute digits will blink. 5. Enter the minutes by pressing either or . 6.
EN INDOOR AND OUTDOOR TEMPERATURE LOW BATTERY WARNING If no readings are received from the remote unit for more than 4 minutes, blanks, “ ” will be displayed until further readings have been successfully searched. Check that the remote unit is sound and secure. You can wait for a little while or press and simultaneously to force an immediate search. When it is time to replace the batteries, the respective low battery indicator will appear on the indoor and outdoor temperature windows.
EN Dimension SAFETY AND CARE This product is designed to give you years of service if handled properly. Observe the following guidelines: • Never immerse the unit in water. This can cause electrical shock and damage the unit. • Do not subject the main unit to extreme force, shock, or fluctuations in temperature or humidity. • Do not tamper with the internal components. • Do not mix new and old batteries or batteries of different types. Do not use rechargeable batteries with this product.
EN Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Power Main unit: 2 x UM-4 (AAA) 1.5V batteries Remote sensor unit: 2 x UM-3 (AA) 1.5V batteries FCC : NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
EN Company Name: Oregon Scientific, Inc. Address: 19861 SW 95th Place, Tualatin, Oregon 97062, USA Website address: www.oregonscientific.com. Name and model number of the product: Remote Thermometer RAR232 NOTE Changes or modifications not expressly approved by Oregon Scientific for compliance could void the warranty and your authority to use this equipment. 11 RAR232A-E CP5.
