User's Guide

of 10% to 90% RH and Atmospheric Pressure of up to 2000m
above sea level (700hPa)). The device can be damaged if
used outside of this range. Store and transport in a cool, dry
place (32° to 104°F (0° to 40°C) and Relative Humidity of 5%
to 90% and atmospheric pressure of 700hPa to 1060hPa)).
The OrCam Read device is water resistant but not waterproof.
This means that it can withstand light rain or drizzle for short
periods of time, although it is not recommended, as long as
the device is covered and protected. Do not use the OrCam
Read device in heavy rain, when at the beach or swimming
pool, or in or near a bathtub or shower. Do not submerge the
OrCam Read device in any type of liquid. IP Code: IP22. Do not
expose the device to chemicals, such as household cleaners,
aerosol sprays, solvents, alcohol, or ammonia. If you experien-
ce an allergic reaction to any of the elements of the OrCam
Read device contact a medical professional.
Should you have a problem operating the OrCam Read device
and believe there is something wrong with the device, do not
attempt to repair it by yourself. Only qualied OrCam person-
nel may repair or service your device. Unauthorized repairs
may void your warranty. Do not attempt to replace the battery;
you may damage it, which could cause overheating and even
injury. The battery is designed to last for two years of average
use (one charging cycle per day on average) after which it
may need to be replaced. Use only the charger supplied with
your OrCam device. Using another charger may void your
warranty and could cause severe injury. During charging, a
distance of at least 2 cm. between the equipment and all
persons should be maintained for the duration of operation of
the equipment. Do not force a connector into a port or apply
excessive pressure to a button. This may cause damage that
is not covered under the warranty. If the connector does not
insert easily, check for obstructions in the port and verify that
you have the correct connector for that port. Do not combine
with software, hardware, or other equipment not supplied by
OrCam. Exposing the OrCam Read device to magnetic elds
may damage the unit or erase your data. When you are using
the OrCam Read device or charging the battery, it is normal
for the device to get warm. If the device becomes excessively
hot, leaks, or gives off a burning smell, turn the device off
immediately and contact OrCam support. NOTE – Product
ambient temperature range when charging is from 0 to 35°C.
Cleaning.
Clean your device if you feel it is dirty or transferred between
camera lens with your nger. Clean the lens with the supplied
microber cloth and eyeglass cleaning uid. Do not use any
abrasive materials. Do not expose the device to chemicals,
such as household cleaners, aerosol sprays, solvents, alcohol,
or ammonia.If you experience an allergic reaction to any
of the elements of the OrCam device contact a medical
professional.
could void the user authority to operate the equipment
under FCC Rules. NOTE: THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
FCC Compliance Statement
This device has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
residential installations. This equipment generates uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio and television reception.
However, there is no guarantee that interference will not
occur in a particular installation. If this device does cause
such interference, which can be veried by turning the
device off and on, the user is encouraged to eliminate the
interference by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the
receiver.
– Connect the device to an outlet on a circuit different
from the one that supplies power to the receiver.
– Consult the dealer or an experienced radio/TV techni-
cian.
CE Compliance - Authorized European Community Repre-
sentative Medes Limited 5 Beaumont Gate, Shenley Hill,
Radlett, Hertfordshire, London WD7 7AR, United Kingdom.
Telephone: [phone] Fax: [phone]Ap-
plicable Standards.
OrCam Read meets Annex VII of the medical device
Directive 93/42/EEC and 2007/47/EEC and the essential
requirements set out in Annex 1.Applied Standards: EN
IEC 60601-1. ETSI EN 301 489-1. ETSI EN 301489-17. FCC
Part 15, Subpart B. IEC/EN 60601-1-6. IEC 62366-1:2015.
EN IEC60601-1-2. EN 62304. RoHS Directive 2011/65/EU.
WEEE. EN ISO 14971:2016. Council Directive 93/42/EEC
of 14 June 1993 concerning medical device.
To contact OrCam Support please e-mail
[e-mail] or call:
Safety and Warnings.
Before using the OrCam Read device, read the following
precautions carefully to avoid dangerous situations and
to ensure ideal performance of your OrCam Read device.
Handle your OrCam Read device with care. It can be
damaged if dropped, burned, punctured, or crushed. Do
not open the device. The OrCam Read device is designed
to work in ambient temperatures between 32° and 104°F
(0° and 40°C) and in normal conditions (Relative Humidity
United Kingdom.
OrCam UK
60 Gresham St.
London EC2V 7BB
0800.358.5323
U.S. & Canada.
OrCam Inc.
115 Broadway, 11th .
New York, NY 10010
1.800.713.3741
Israel.
OrCam Technologies
5 Kiryat Hamada
Jerusalem
+972.2.591.7800
FCC ID:
2AAWI-READ
Refer to User Ins-
truction Guide
Waste Electrical and
Electronic Equipment
Directive Compliant
Contact OrCam for proper
disposal
Restriction of Hazardous
Substances Directive
Compliant (materials and
(components
CE Compliant