User Guide

Contents
xi
Manual stimulus configuration . . . . . . . . . . . . . . . . . . . . . 261
To manually configure a stimulus . . . . . . . . . . . . . . . . . 261
Transient (time) response . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
Internal time steps in transient analyses . . . . . . . . . . . . . . . . . . 265
Switching circuits in transient analyses . . . . . . . . . . . . . . . . . . . 266
Plotting hysteresis curves . . . . . . . . . . . . . . . . . . . . . . . . . . . 266
Fourier components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
Parametric and temperature analysis 271Chapter 11
Chapter overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Parametric analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
Minimum requirements to run a parametric analysis . . . . . . . . . 272
Overview of parametric analysis . . . . . . . . . . . . . . . . . . . . 273
RLC filter example . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Entering the design . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Running the simulation . . . . . . . . . . . . . . . . . . . . . . . 275
Using performance analysis to plot overshoot and rise time . . . 275
Example: frequency response vs. arbitrary parameter . . . . . . . . 278
Setting up the circuit . . . . . . . . . . . . . . . . . . . . . . . . . 278
Temperature analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Minimum requirements to run a temperature analysis . . . . . . . . 281
Overview of temperature analysis . . . . . . . . . . . . . . . . . . . . 282
Monte Carlo and sensitivity/worst-case analyses 283Chapter 12
Chapter overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Statistical analyses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
Overview of statistical analyses . . . . . . . . . . . . . . . . . . . . . 284
Output control for statistical analyses . . . . . . . . . . . . . . . . . . 285
Model parameter values reports . . . . . . . . . . . . . . . . . . . . . 285
Waveform reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Collating functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Temperature considerations in statistical analyses . . . . . . . . . . 288
Monte Carlo analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
Reading the summary report . . . . . . . . . . . . . . . . . . . . 291
Example: Monte Carlo analysis of a pressure sensor . . . . . . . . . 293
Drawing the schematic . . . . . . . . . . . . . . . . . . . . . . . . 293
Defining part values . . . . . . . . . . . . . . . . . . . . . . . . . 294
Setting up the parameters . . . . . . . . . . . . . . . . . . . . . . 295
Using resistors with models . . . . . . . . . . . . . . . . . . . . . 296
Saving the design . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
Defining tolerances for the resistor models . . . . . . . . . . . . 297
Pspug.book Page xi Wednesday, November 11, 1998 1:14 PM