WARNING YJ USA Corp., 3970 Lindbergh Drive Adison, TX 75001 www.jumppod.
3
1. The owner and supervisors of the trampoline are responsible to make sure all the users are aware of practices specified in this manual. 2. Trained Spotter supervision is recommended. 3. Place the trampoline and trampoline enclosure on a level surface before use. 4. Must place the trampoline on lawn, bark wood chip, sand or cushioning materials. 5. Adequate overhead clearance is essential. A minimum of 7.3 m (24 ft) from ground level is recommended.
25. Do not attach anything to the barrier that is not a manufacturer approved accessory or part of the enclosure system. 26. Wear clothing free of drawstrings, hooks, loops, or anything that could get caught in the barrier. 27. Enter and exit the trampoline enclosure only at the door designed for that purpose. 28. Do not attempt to crawl under the barrier. 35. While keeping the head erect, focus eyes on the trampoline toward the perimeter. This will help control bounce. 36.
Note: The OR1413B6 6
the sharply spot.
1. Make sure you understand the information in the box at the top of this page before you begin assembling the trampoline. 1 Lay two Top Tubes (1) on the ground as shown. Make sure there is a T-Connector (2) on Top Tube (1). Center Insert the small end of one Top Tube(1) into Top tube(1) with T-connector(2). Insert a Center(4) into the leg, slide a second leg (3) onto the center. Insert Leg(3) into the T-connector(2). 3 3 1 2 You have now assembled one leg section.
3. Lay the Bed (5) on the ground inside of the assembled frame. Make sure that the two warn top of the Bed. ing decals (not shown) are on Note: There are V-rings around the edge of the 5 Frame V-rings Bed (5) and holes around the top of the frame. During this step, you will attach the Bed to the frame using the included Springs (7) for holes on top of frame and for holes on bottom of frame (see the inset drawing).
4 4. Lay the Frame Pad (6) on the frame. Double D-rings on the middle of pad should be fixed exactly on the right of each T-connector of frame. Do not use the trampoline without the Frame Pad (6), which is designed to reduce the likelihood of injury to the user from coming in contact with the trampoline frame. If you do not have a Frame Pad, call our Customer Hot Line toll-free at 1-877-927-8777, Monday-Friday,8 a.m. -5 p.m. Central Time.
6 6. Using the included plastic tie, attach the Safety Placard (8) to the frame near the point where jumpers will climb onto and off the trampoline. The trampoline is now fully assembled. Make sure that all parts are securely attached. Familiarize yourself and all users of the trampoline with the safety precautions, use and instructional materials, and care and maintenance instructions in this manual before using the trampoline. Frame 7.
10. Attach the other three Pole(13,14) in the same way. See inset drawing. 10 Leg Attach the Poles(13,14) as above arrow drawing shown. 11. Lay out Top G3 Pole (15), joint each section Connector to a straight line as shown. 6 Sections Per Line Top G3 Pole (15) Spread out G3 Pole and Joint each section to one straight line. Assemble the remaining Top G3 Pole (15) in the same way.
13. Note: During steps 14 and 15, you will “sew” the lower edge of the Netting(17) to the V-rings on the bed using the Cords(22). 13 Locate the V-ring closest to the door. Thread one end of a Cord(22) through the lower edge of the Netting(17) above the V-ring and then thread the Cord through the V-ring. Tie the Netting to the V-ring, by making a double knot in the Cord. 17 14.
Stake It is possible for the trampoline/enclosure be blown about by high wind. If you anticipate high winds, the trampoline/enclosure should be moved to a sheltered location, disassembled, or tied down to the ground with ropes and stakes (not included). At least three ropes and three stakes should be used. The tops of the stakes should be at ground level so that they will not create a tripping hazard.
OR1413B6 15 17 14 9 16 13 6 5 21 8 10 2 3 20 8 1 12 11 4 15 (BLACK) 7 1 2 3 4 5 6 7 8 12 12 12 6 1 1 72 1 9 10 11 4 16 8 8 19 18 Top Tube(With T-connector) T-Connector Leg Extension Leg Center Stitched Bed with V-ring Frame Pad Springs User’s Manual and safety Placard (2 pcs) Self-tapping screw Locknut U-bolt Bracket 12 13 14 15 16 8 4 4 2 4 17 18 19 20 21 22* * 1 8 1 4 16 8 1 U-bolts Bottom Enclosure pole Top Enclosure pole G3 Pole (Black) Hemisphere Cap ( This part has been att
1 12 2 12 Top Tube with T-connector T-connector Note: This part may be pre-assembled onto key#1 3 12 4 6 Leg Center 5 1 Stitched Bed with V-ring 6 1 Frame Pad 7 72 8 1 Safety Placard 19 1 Spring pulling tool Leg Extension Springs 23
8 1 Safety placard 9 4 Self-tapping screw 10 16 Locknut 11 8 U-bolt Bracket 12 8 U-bolt 13 4 Bottom enclosure pole 14 4 Top enclosure pole 15 2 G3 pole 16 4 Hemisphere Cap 17 1 Netting with attached hardware 18 8 Foam sleeves 20 4 WEDGE 21 16 U-bolt plastic cap 22 8 Cord (Pre-assembled to key#16) 24
