Installation Guide

USER'S GUIDE
WARNING: Read all instructions carefully before installing.
Thank you for selecting the quality of Orbit
®
and the Misting
Booster Pump. This pump works with your ⅜-in mist cooling
system, increasing the line pressure up to 160 PSI.
WARNINGS
• THIS PUMP IS NON-SUBMERSIBLE.
• Risk of electric shock. This pump is supplied with a grounding
conductor and grounding type attachment plug. To reduce the
risk of electric shock, be certain that it is connected only to a
properly grounded, grounding type receptacle.
• This pump is for use indoors or outdoors with cold water only.
NOTE: Orbit
®
mist systems are for outdoor use only.
CAUTIONS
• Optimal water inlet pressure is 40 PSI
• Maximum working pressure is 160 PSI
• Install with all electrical components above ground and with
the properly grounded electrical outlets.
• Unplug the pump before servicing this unit
• Do not use with flammable liquids
• This pump has been evaluated for use with cold water only
• A pressure reducer is strongly recommended if your standard
hose faucet pressure is greater than 40 PSI
• Test the Ground Fault Circuit Interrupt plug before each use.
1. Plug into receptacle.
2. Press RESET button: Indicator should be ON.
3. Press TEST button: Indicator should be OFF.
4. Press RESET button for use. Do not use if test fails
WARRANTY AND STATEMENT
Orbit
®
Irrigation Products, Inc. warrants to its customers that
its Orbit
®
products will be free from defects in materials and
workmanship for a period of four years from the date of purchase.
We will replace, free of charge, the defective part or parts found
to be defective under normal use and service for a period of up to
four years after purchase (proof of purchase required). We reserve
the right to inspect the defective part prior to replacement. Orbit
®
Irrigation Products, Inc. will not be responsible for consequential
or incidental cost or damage caused by the product failure. Orbit
®
liability under this warranty is limited solely to the replacement or
repair of defective parts.
Questions please call: 1-800-488-6156 or 1-801-299-5555
www.orbitonline.com
INSTALLATION
1. Determine the location of the pump before proceeding.
Consider your water and power locations and locate the pump
within range of both resources.
NOTE: This pump should be securely fastened to a fixed
post or wall. Be sure to use appropriate wall anchors when
fastening to a stucco wall.
2. Remove the clips on each port.
3. Press down on the inner ring and pull out the temporary plug.
NOTE: Plug shapes may differ from that shown in the illustration.
4. Insert the appropriate supply line into each port.
NOTE: The inlet and outlet ports are clearly marked to ensure the
lines are installed correctly.
5. Connect the other end of the inlet line to your water source.
NOTE: For optimal performance, install a calcium inhibitor filter
(Model 10109W) between the pump and the water source. Run
water through the filter for at least 2 minutes before connecting to
the pump. This will flush any debris that may be in the filter.
6. Turn on the water source to ensure water pressure to the pump.
7. Connect the pump to the power supply.
8. Switch the pump to the ON position.
NOTE: The power switch is located on the side of the housing.
OPERATING TIPS
• Before operating the system, be sure the outlet pressure
(mist line) is relieved to prime the pump.
• The booster pump is not equipped with an automatic valve.
When shutting down the system, the water source must be
turned off to keep the system from running at line pressure.
NOTE: This pump is fitted with a thermal protection switch that will
prevent the unit from damage due to overheating. This switch is
automated and will shut the pump off prior to any internal damage
to the unit. Operation will typically resume within one hour of
automatic shut-off.
Printers are responsible
for meeting print
production requirements.
Any changes must be
approved by Orbit
®
.
Printed piece must meet
designated specifications
on this form.
© 2015 Orbit Inc.
This work is the property
of Orbit
®
, and cannot be
used, reproduced or
distributed in any way
without their express
permission.
Dieline
PMS
0000
Fold
PMS
0000
Product
Coverage
PMS
0000
Dims./
Callout
PMS
0000




Orbit
®
1.801.299.5555
orbitonline.com
Glue
Folded Flat Additional Information
PRIN TERS ARE
REQUIRED TO MATCH
ALL SP ECIFIED
PMS COLORS.
K
DATE: 12/10/2015
DESIGNER: NK MARKETING: CD
SOFTWARE: Adobe Indesign CS6
ARTWORK №: 9210024 rG
L:
W:
H:
000.000" W:
H:000.000"
000.000"
11.0"
8.5"
OUT
IN
Remove
Clips
Ports
OUT
IN
Pull
Press
MISTING
BOOSTER
PUMP
Orbit
®
Irrigation Products Inc.
845 North Overland Road
North Salt Lake, Utah 84054 USA
www.orbitonline.com
800-488-6156
801-299-5555
PN 92100-24 rG