User Manual

more than 10 times in any given 10 minute period. After entering
into stage 2 it will enter into stage 3 if there are more than 9
activations within the next 15 minutes.
OPERATION DIAL FEATURES
OFF
Turns the sensor and valve off. Must be in this mode to install
batteries or to turn Intelligent Sensing on or off. Resets the time
delays between valve activation if Intelligent Sensing is on.
DAY
Activates sensor and valve only during daylight.
NIGHT
Activates sensor and valve only when dark.
ALWAYS
Sensor and valve are always active.
DURATION ADJUSTMENT KNOB
Adjust the duration of the water from approximately 3 seconds
to 10 seconds.
• Turn knob towards the + to increase how long the water sprays.
• Turn knob towards the – to decrease how long the water sprays.
SENSOR ADJUSTMENT KNOB
The sensor range is adjustable up to 40 ft. For smaller animals
increase the distance the sensor monitors. For larger ones
decrease the distance.
• Turn knob towards the + to increase the distance
the sensor monitors.
• Turn knob towards the – to decrease the distance
the sensor monitors.
30 MIN. WATER CYCLE BUTTON
• Press button to activate a 30 minute watering cycle.
• Press button again to stop the 30 minute watering cycle.
• A slight delay allows the user to move a safe distance
away from the unit before watering begins
IMPACT SPRINKLER OPERATION
ADJUSTING THE PATTERN
Determine where you want the stream of water to go and position
a friction collar to the left and right of that area. Place the trip
pin in-between the two friction collars in the down position. If you
want to water in a 360º circle push the trip pin to the up position.
ADJUSTING THE DISTANCE OF SPRAY
There are two ways to reduce the distance of the spray.
1. Screw diffuser pin into stream.
2. Press down deflector shield and turn distance control knob.
YARD ENFORCER® TIPS AND TRICKS
Position the sensor and sprinkler in the direction of where the
pest enters the yard to chase them away before they reach the
plants and landscaping you are protecting.
Certain animals are intelligent enough to recognize the pattern
and range of the Yard Enforcer and learn how to avoid the spray.
Weekly adjustments may be necessary to continue to discourage
these animals. Another option is to create a sprinkler "minefield"
to better deter certain types of animals.
Create a sprinkler "minefield" by attaching additional sprinklers
to the riser outlets.
Enforce different areas in your yard at the same time by adding
additional Yard Enforcers to the step-spike outlet.
TROUBLESHOOTING
Water is leaking from joints.
Check if:
• Connections and swivel couplings are tight.
• Washer is missing, pinched, or damaged and replace if needed.
Sprinkler won’t activate.
Check if:
• Operation dial is set to appropriate time of day.
• Valve cable is connected to sensor unit.
• Batteries are low and replace if needed.
• Hose faucet is on.
Sensor not detecting movement.
Check if:
• Range adjustment is set too low and adjust range if needed.
• Angle of sensor on mounting arm is too steep and adjust
sensor angle if needed.
• Object in front of sensor is moving and producing heat.
• Intelligent Sensing increases the delay between activations.
Deactivate Intelligent Sensing mode if desired (see Intelligent
Sensing section).
• There is dust, dirt or hard water build-up on the white lens
which will limit sensitivity. Wipe the lens gently with a damp
cloth if needed.
Sprinkler is activating without movement.
Check if:
• Sensor is detecting tree movement with the sun behind the tree.
• Activate Intelligent Sensing mode if desired.
• Sensor is being triggered falsely. Ensure sensor is not pointed at
moving objects, such as water or windy areas.
Sprinkler is taking longer to turn off.
Check if:
• Batteries are low and replace if needed.
Working Water Pressure
Minimum: 20 PSI
Maximum: 100 PSI
(If you do have high pressure Orbit® recommends adding
a pressure reducer to increase hose life).
YARD ENFORCER® ASSEMBLY
1. Thread the riser onto the valve.
2. Slip the mounting arm with attached sensor unit
onto the riser.
3. Thread the impact sprinkler onto the riser above
the mounting arm.
4. Thread the step-spike onto the valve and tighten
the swivel coupling.
5. Insert the valve cable into the sensor aligning the grooves.
QUICK-START INSTRUCTIONS
1. Attach an outdoor hose to the step-spike inlet.
2. Position the step-spike in your chosen location, then step
on the spike crossbar until the top of it is flush and level
with the ground.
3. Make adjustments to the impact sprinkler head so when
activated the spray is in the direction of the desired
coverage zone.
4. Adjust the duration of the spray by turning the labeled knob.
5. Adjust the range of the sensor by turning the labeled knob.
6. Set the operation dial to your desired on position.
7. Turn on water.
8. Make further adjustments to the impact head, duration,
and range as needed to fine-tune the enforced area.
GETTING TO KNOW YOUR YARD ENFORCER®
The sensor detects the combination of both heat and movement
to activate the valve.
Move the sensor unit left or right by applying pressure to the unit
in either direction.
Face the sensor unit up or down by loosening the attachment
knob, moving it into place, and then tightening the attachment
knob.
INTELLIGENT SENSING
The Yard Enforcer is programed with Intelligent Sensing.
This feature automatically increases the time between each of
the valve activations to prevent overwatering. Turn this feature
off by rotating the dial to “OFF” and holding the 30 minute water
Cycle Button for 20 seconds. The sprinkler will activate briefly to
confirm. Repeat the above steps to turn Intelligent Sensing back
on.
Stage 1 Intelligent Sensing: 10 second delay between
each valve activation.
Stage 2 Intelligent Sensing: 60 second delay between each
valve activation. This stage will last for one hour*
Stage 3 Intelligent Sensing: 10 minute delay between each valve
activation. This stage will last for two hours.
Intelligent Sensing Off: 15 second delay between each
valve activation.
*The Yard Enforcer will enter into stage 2 if the valve is activated
INSTALLING THE BATTERIES
1. Verify the operation dial is in the “OFF” position.
2. Remove the tray on the back of the sensor by sliding it out.
Battery tray is waterproof. You may need to use a screwdriver
to push on the tab and slide the compartment out.
3. Insert four AA (1.5V) alkaline batteries (not included) as
directed on the tray and replace the tray.
Note:
Do not mix old and new batteries.
Use only alkaline batteries.
MOTION ACTIVATED PEST DETERRENT SPRINKLER
MOTION ACTIVATED PEST DETERRENT SPRINKLER
MOTION
ACTIVATED PEST DETERRENT SPRINKLER
27629-24 rC
Orbit
®
Irrigation Products, Inc.
North Salt Lake, UT 84054
© 2014 Orbit Irrigation Products, Inc.
All rights reserved. All trade names are registered
trademarks of respective manufacturers listed.
Riser
Mounting Arm
Sensor
Impact Sprinkler
Step-spike
Valve
Valve Cable
Model 27629
Waterproof
Battery Tray
Operation
Dial
Duration
Adjustment
Knob
Sensor Range
Adjustment
Knob
30 Min. Water
Cycle Button
Attachment
Knob
WHEN EXPECTING FREEZING TEMPERATURES,
YARD ENFORCER® SHOULD BE REMOVED FROM THE
HOSE AND STORED INDOORS TO AVOID POTENTIAL
FREEZE DAMAGE.
FILTER TRAPS DIRT PARTICLES, PROLONGING LIFE
OF YOUR YARD ENFORCER®. CLEAN FILTER REGULARLY
AND REPLACE IF WORN.
Working Temperature
Maximum: Do not operate at temperatures exceeding 120°F
Minimum: Keep from freezing. To prevent damage from freezing
water, take the Yard Enforcer® inside and remove the battery
before the first winter frost.
Warnings
For outdoor use with cold water only.
Not for use on appliances.
Do not spraynear electrical connections.
Improper setup or use of sprinklers increases the risk of water
damage to property. Limit the supply of water to the sprinkler
by opening the valve to a ¾ turn position. Use high quality hoses
and maintain pressures within the working pressure range stated
above. Install a pressure reducer if you have high pressure from
the hose faucet. Only opening the tap part way does NOT lower
water pressure.
Use the step on the stake when pushing into the ground. Do not
apply pressure or weight on the sensor housing or sprinkler. (If
you do have high pressure Orbit® recommends adding a pressure
reducer to increase hose life).
Distance
Control
Knob
Trip Pin
Diffuser
Pin
Deflector
Shield
Friction
Collar
Printers are responsible
for meeting print
production requirements.
Any changes must be
approved by Orbit
®
.
Printed piece must meet
designated specifications
on this form.
© 2014 Orbit Inc.
This work is the property
of Orbit
®
, and cannot be
used, reproduced or
distributed in any way
without their express
permission.
Dieline
PMS
0000
Fold
PMS
0000
Product
Coverage
PMS
0000
Dims./
Callout
PMS
0000
∙ Proofing Code: LB1389500
∙
∙
∙
Orbit
®
1.801.299.5555
orbitonline.com
Glue
Folded Flat Additional Information
PRIN TERS ARE
REQUIRED TO MATCH
ALL SP ECIFIED
PMS COLORS.
K
DATE: 08/24/2014
DESIGNER: KM MARKETING: CD
SOFTWARE: Adobe Indesign CS6
ARTWORK №: 27629-24 rC
L:
W:
H:
003.500" W:
H:011.000"
000.000"
17.0"
11.0"
Swivel Coupling