Installation Instructions

p 801 295 9820
f 801 951 5815
www.fluid-studio.net
1065 South 500 West
Bountiful, Utah 84010
proof no: 4
date: 11.28.07
des: SM spck: SM
job no: 07WTM005465
client: Orbit
sku: 55461
upc: ? ????? ????? ?
file name: 07WTM005465
55461-24 rA.indd
software: InDesign CS2
colors
additional instructions:
·
·
color
non printing
PMS
????
PMS
????
color
non printing
PMS
????
Registration
K
Printers are responsible for
meeting print production
requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
designated specifications
on this form.
dimensions:
flat: w: 14.9375" h: 5.5"
finished (folded): w 3.75" d: 0" h 5.5"
© 2007 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.
Pre-Set the Rotation
Voyager
®
sprinklers are preset to
rotate approximately 180°. Sprinklers
may be adjusted with water on
or off. It is recommended that
initial adjustment be made before
installation.
1. Using the palm of your hand, rotate
the nozzle turret counterclockwise
to the left stop to complete any
interrupted rotation cycle. (See
Figure 1.)
2. Rotate the nozzle turret clockwise
to the right stop. This is the fixed
side of the arc. The nozzle turret
must be held in this position for all
arc adjustments.
To Increase the Arc
1. Insert a flat bladed screwdriver into
the pattern adjustment screw (See
Figure 4).
2. While holding the nozzle turret
at the right stop, turn the screw
clockwise. Each full turn of the
screw increases the arc 90°.
3. Adjust to any arc between 40° &
360°.
4. When the maximum arc (360°)
is reached, the screw will stop
turning or there will be a ratcheting
noise.
To Decrease the Arc
1. Insert a flat bladed screwdriver
into the pattern adjustment screw
(See Figure 4).
2. While holding the nozzle turret
at the right stop, turn the screw
counterclockwise. Each full turn of
the screw decreases the arc 90°.
3. Adjust to any arc between 40° and
360°.
4. When the minimum arc (40°)
is reached, the screw will stop
turning or there will be a ratcheting
noise.
Sprinkler Installation
Flush Lines
Turn the water on to thoroughly flush
the lines of dirt and debris before
installing any sprinkler heads.
Install the Sprinkler Head
1. Complete steps 1 and 2 under
“Pre-Set the Rotation.”
2. Select and install a riser to obtain
the proper height. (See Figure 3.)
When the sprinkler is buried the
cap should be flush with the finish
grade.
3. Thread the sprinkler onto the
riser. When the threads are snug,
visually orient the arrow on top of
the cap so that it points at the right
stop by turning the entire sprinkler
head on the riser. When the water
is turned on, the sprinkler turret will
begin to rotate toward the left stop.
Note: Do not use pipe dope on the
threads. If necessary, use thread
seal tape.
4. Space adjacent heads for
overlapping head-to-head
coverage.
Radius Adjustment
Insert a small flat bladed screwdriver
into the distance adjustment
screw. (See Figure 4.) Turn the
screw clockwise (into the stream
of water) to decrease the radius, or
counterclockwise to increase the
radius. (Do not rotate the screw too
far either way or the nozzle or screw
may come out.)
Precipitation Rate Adjustment
For excessively wet or dry areas, the
precipitation rate can be adjusted:
replace the existing nozzle with
a larger one to increase the rate
or a smaller one to decrease the
rate of precipitation. Note: It is
not necessary to disassemble the
sprinkler to make adjustments.
Nozzle Installation
1. To gain access to the nozzle, insert
a flat blade screwdriver into the
lifting socket (Figure 2) and lift
upward.
2. While holding the riser up with one
hand (See Figure 5), use a small
flat bladed screwdriver to loosen
the adjustment screw far enough
to clear the nozzle. If a nozzle is
already installed in the sprinkler, it
can be removed by briefly turning
on the water, or by pulling on one
of the nozzle “ears” with needle-
nose pliers.
3. Slip the desired nozzle into the
nozzle socket. Note that the socket
is angled up 25°. Also note that
the “ears” should be located at
the top. (See Figure 5.) Rotate the
adjustment screw in far enough to
secure the nozzle.
Cleaning the Filter
1. To access the filter, unscrew the
sprinkler from the riser. Unscrew
the cap and remove the cap/spring
assembly from the body.
2. Replace the filter and screw the
cap/spring assembly back on
the sprinkler body. Reinstall the
sprinkler on the riser, being careful
not to disturb the surrounding soil.
Winterizing Your System
In freezing climates, your sprinkler
system must be drained prior to
freezing to prevent damage.
1. Turn off the water supply.
2. Open all valves and manual
drains to allow water to escape
(compressed air can be used to
completely purge the system of
water).
CAUTION
For outdoor use with cold water only.
Do not spray near electrical connections.
Para uso exterior con agua fría únicamente.
No rocíe cerca de las conexiones eléctricas.
PN 55461-24 Rev A
Pattern

Adjustment
Distance

Adjustment
Or
bi
t
®
Professional
Pattern

Adjustment
Distance

Adjustment
Orb
i
t
®
Professional
3
2
FIGURES • FIGURAS
Pre-set the rotation
Preconfigure la rotación
1
Lifting socket
Soporte de elevación
Adjustment
Ajuste
Nozzle installation
Instalación de la boquilla
5
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Pattern adjustment slot
Ranura de ajuste del patrón
A
Distance adjustment slot
Ranura de ajuste de la distancia
B
Orbit
®
B
A
Sprinkler installation
Instalación del aspersor
4
Voyager
®
gear DriVe
Sprinkler
Aspersor de
trAnsmisión
por engrAnAjes
Orbit
®
Irrigation Products, Inc.
North Salt Lake, Utah 84054 USA
1-800-488-6156
www.orbitonline.com
© 2007 Orbit
®
Irrigation Products, Inc.
All rights reserved. All trade names are registered
trademarks of respective manufacturers listed.
07WTM005465 55461-24 rA.indd 1 11/29/07 2:16:26 PM