V3 User Manual
BIND - Triggers binding procedure if receiver is powered with the bind plug inserted in this port. In normal operation it is CPPM
or SBUS output (depends on the model of the receiver you purchased)
THRO - During binding procedure if a bind plug is inserted in this port – turns telemetry function OFF In normal operation – PWM
throttle output
AILE - PWM aileron output
ELEV - PWM elevator output
RUDD - PWM rudder output
GEAR - PWM gear output
AUX1…AUX7 - PWM auxiliary outputs. Number of outputs depends on the receiver you purchased.
SAT1 - main satellite port. If you connect only one satellite please use this port.
SAT2 - secondary satellite port.
Satellite port is fully compatible with all JR and Spektrum satellites as well as all Orange satellites.
Recommended satellites:
OrangeRx R110XL 2.4Ghz DSMX/DSM2 compatible Satellite Receiver (long antenna version) (PRODUCT ID: 9171000564-0)
OrangeRx R110X 2.4Ghz DSMX/DSM2 compatible Satellite Receiver (PRODUCT ID: 9171000299-0)
OrangeRx R111XN 2.4GHz DSMx/DSM2 compatible nano satellite (PRODUCT ID: 9171000581-0)
RPM • RPM sensor input. You can use Orange RPM Sensor (PRODUCT ID: 9020000008-0) connecting it directly to this
port.
-(A)- • Current sensor input. You can use Orange Current Sensor (PRODUCT ID: 9171000552-0) connecting it directly to
this port.
Vb t° • Battery voltage and temperature sensor. You can use Flight Pack Voltage & Temperature Sensor for OrangeRx
Telemetry system (PRODUCT ID: 9171000551-0) connecting directly to this port.
During binding procedure:
Orange LED is blinking rapidly. After receiving binding signal from the transmitter blinks slowly for several seconds and then
becomes solid if connection is correct.
In normal operation
In presence of transmitter signal: Orange LED is solid. If the transmitter signal is lost Orange LED is OFF.
Red LED blinks number of holds (up to 256) – signal losses with more than 1 second when receiver had to trigger a failsafe
event. The LED will flash the number of holds then pause (e.g., flash, flash, flash, pause, flash, flash, flash, pause indicates
three holds occurred since the receiver was last turned on). Note that holds are reset to zero when the receiver is turned off.
During the first flights of a new airplane, it’s recommended to check the red LED hold indicator. If it’s flashing, it’s important to
optimize the installation (move or reposition antennae) until no hold occurs. On later flights, the LED Hold Indicator can be
used to confirm RF link performance
Before each flying session and especially with a new model, it is important to perform a range check. Please use instructions
of your transmitter to perform a range test.
You can turn On and Off telemetry using Programming Card (PRODUCT ID: 9171001376-0, sold separately):
- None - no telemetry
- Analog
Telemetry Data:
• Battery voltage (up to 52VDC) – connect directly to the battery pack up to 12S
• Receiver pack voltage (up to 9.6VDC)
• Temperature (-15°C~120°C). Use Flight Pack Voltage & Temperature Sensor for OrangeRx Telemetry system.
(PRODUCT ID: 9171000551-0)
• Current (up to 100A) – please use current sensor (PRODUCT ID: 9171000552-0)
• RPM (1000~300000rpm) – please use RPM sensor (PRODUCT ID: 9020000008-0)
*Note:
1) This is not a Spektrum DSMX product, nor is it a copy of a Spektrum DSMX product. The
Spektrum and DSMX brand is a trademark of Horizon Hobbies USA.
2) This is not an underground black market fake Spektrum product. OrangeRx quality is
guaranteed.
3) Accepted by the MAAA in Australia, see the MAAA MOP58 for guidance
Orange Current Sensor (PRODUCT D: 9171000552-0)
• voltage, current, RPM, temperature are collected from TM connectors of the receiver(Default settings).
Integrated telemetry (TM) function was tested on Spektrum and OpenTx transmitters with telemetry enabled Tx
modules and confirmed that it works correctly on these systems. The settings for the OpenTx and the Tx module can
vary, please refer to the manuals and instructions of your transmitter and TX module and make settings needed.
Integrated TM measures data in-flight on the aircraft and transmits it back to transmitter to display or/and trigger
sound and visual alarms if they are set. Please refer to your transmitter manual to see how to see the telemetry
connection indicator, display telemetry data and set up alarms (current, battery voltage, motor RPM, temperature).
Orange RPM Sensor
(PRODUCT ID: 9020000008-0)
Orange Current Sensor
(PRODUCT ID: 9171000552-0)
Flight Pack Voltage & Temperature
Sensor for OrangeRx Telemetry
system.
( PRODUCT ID: 9171000551-0)
•
•
•
•