User Manual

ManualsBrandsOrange ManualsHobbyOrangeRX DSMX/DSM2/Devo Compatible 2.4GHz Selectable Transmitter Module (JR/Turnigy Compatible)

RANGE

DSMX/DSM2/D

EVO

2.4GH

WITCHABLE

RANSMITTER

ODULE

(JR/T

URNIGY

OMPATIBLE

)

SER

ANUAL

EATURES

• Works with any JR/Turnigy/Taranis compatible module-based transmitter

• 5 switchable modes: DSM2 1024/22ms, DSM2 2048/11ms, DSMX 22ms, DSMX 11ms, Walkera

• 4 switch selectable power outputs: 1, 5, 25, 70mW

• Easy to access bind button

• Range check mode (1mW)

• Selectable channel mapping (AETR, TAER)

Current consumption: 100mA

OMPATIBILITY

Standard JR style 5 pin module-based transmitters (JR/Turnigy compatible)

2.4Ghz protocol: DSMX / DSM2 / Walkera Compatible

Input Voltage: 6 - 18VDC

Power: 1, 5, 25, 70mW (selectable)

Radio Type: Full range system

UTPUT PROTOCOLS

DSM2 –1024/22ms, 2048/11ms

DSMx – 22ms/11ms

Walkera Devo

X MODULE

NSTALLATION

The Tx module can be installed and used in following radio transmitters:

- All JR compatible radios with external Tx module compartment

- Turnigy 9XR and 9XR Pro

- Taranis X9D and compatible

NTENNA

OLARIZATION AND ORIENTATION

For optimum RF link performance it’s important that the antenna be oriented in the way

that allows for the best possible signal reception when the aircraft is in all possible attitudes and

positions. Follow simple rules:

- Never point antenna to the aircraft. Pointing antenna to the aircraft will give you the worst reception.

- Don’t block an antenna with metal objects (frames, trays, monitor and smartphone holders). This weakens the signal.

- In the most situations it is better to position antenna horizontally to get better performance and avoid pointing antenna to the aircraft.

CHANGE

To make sure that many models can be controlled at the same time and place without interference to each other a unique ID is assigned to

each control communication. A transmitter module provides this ID to the receiver during binding procedure. There is totally more than 4 billion

Summary of content (5 pages)

PAGE 1
ORANGERX DSMX/DSM2/DEVO 2.
PAGE 2
combinations available. You may want to change ID before binding to another model to make sure that if you accidently turned previous model ON with settings for the new model, the previous one will not respond to your radio transmitter. RANGE TESTING Before each flying session and especially with a new model, it is important to perform a range check. Make sure that your transmitter battery is fully charged. Be careful and make sure that all propellers on your aircraft are removed.
PAGE 3
ON-2048 Note: Switch position will be ignored in Auto mode(when SW3 is ON) and for DSMx SW7, SW8: Output power selection (Table 1) Range test Note: SW7 SW8 Power OFF OFF 18.5dBm 70mW OFF ON 13.2dBm 25mW ON OFF 7dBm 5mW ON ON 0,5dBm 1mW N/A N/A 0,5dBm 1mW During binding procedure the output power is fixed at 0.006mW regardless of the switch positions During Range test procedure the output power is fixed at 1mW regardless of the switch positions.
PAGE 4
Buzzer – – beeps 3 times on power ON after detecting PPM on the PPM input (AETR/TAER) LED – DSM2, 1024 mode – OFF DSM2, 2048 mode – single blinks DSMx, 22ms mode – double blinks DSMx, 11ms mode – triple blinks Functionality: Power ON: When powered up the module is waiting for valid PPM signal to be detected. As soon as PPM signal is detected the buzzer generates three short beeps (0.1s) indicating that the system is ready.
PAGE 5
successful. If the bind was unsuccessful it generates one long beep. After binding procedure is over the module enters the regular transmitting mode and stays in this mode until power turned off. ID change: When powered up with Button1 pressed the new ID will be generated. The new ID wil be generated regardless if PPM signal present or not. After detection of Button 1 pressed module waits for 3 sec then generated a new ID and buzzer makes long beep(0.3 sec).