Table of Contents Table of Contents.................................................................................... 1 Usage Notice........................................................................................... 2 Safety Information..........................................................................................2 Precautions....................................................................................................3 Eye Safety Warnings.........................................
Usage Notice Safety Informations The lightning flash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of import operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Usage Notice Precautions Please follow all warnings, precautions and maintenance as recommended in this user’s guide. ▀■ Warning- Do not look into the projector’s lens when the lamp is on. The bright light may damage your eyes. ▀■ Warning- To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture. ▀■ Warning- Please do not open or disassemble the projector as this may cause electric shock.
Usage Notice Do: Turn off the product before cleaning. Use a soft cloth moistened with a mild detergent to clean the display housing. Disconnect the power plug from the AC outlet if the product is not being used for a long period of time. Don’t: Do not block the ventilation slots and openings on the unit. Do not use abrasive cleaners, waxes or solvents to clean the unit. Do not use under the following conditions: - In extremely hot, cold or humid environments.
Usage Notice Eye Safety Warnings ▀■ Avoid staring directly into the projector’s beam of light at all times. ▀■ Minimize standing facing into the beam. Keep your back to the beam as much as possible. ▀■ Using a stick is recommended to avoid the need for the presenter to enter the beam. ▀■ Ensure that projectors are located out of the line of sight from the screen to the audience; this ensures that, when presenters look at the audience, they do not also have to stare at the projector lamp.
Introduction Product Features This product is a Short throw XGA single chip 0.55” DLP® projector. Outstanding features include: True XGA, 1024 x 768 addressable pixels Texas Instruments Single chip DLP® Technology Computer Compatibility: Apple Macintosh, iMac, and VESA Standards: UXGA, SXGA+, SXGA, WXGA, XGA, SVGA, VGA Video Compatibility: ■ NTSC, NTSC4.
Introduction Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if anything is missing. Projector with lens cap Power Cord 1.8m VGA Cable 1.8m Due to the difference in applications for each country, some regions may have different accessories.
Introduction Product Overview Main Unit 1 2 1 3 4 VG A-O ut VG A-In /SC A RT DV H S-V ideo Vid eo RS -232 5 US B RJ- 45 Aud io-In Aud io-L Aud 6 io- 7 1. 2. 3. 4. English 8 IR Receivers Control Panel Focus Projection Lens 5. Power Socket 6. Connection Ports 7.
Introduction Control Panel 5 1 2 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Introduction Connection Ports 2 1 4 3 6 5 8 10 7 11 9 Audio-Out VGA-Out 12 VGA-In / SCART VGA-In DVI-I S-Video Video RS-232 USB RJ-45 Audio-In 13 Audio-L 14 Audio-R 15 1. VGA-Out Connector (Monitor Loop-through Output) 2. VGA-In/SCART Connector (PC Analog Signal/Component Video Input/HDTV/SCART) 3. DVI-I Connector (PC Digital (HDCP)/PC Analog/Component Video Input) 4. S-Video Input Connector 5. Composite Video Input Connector 6. RS-232 Connector 7.
Introduction Remote Control 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23.
Installation Connecting the Projector Connect to Computer/Notebook MOLEX 5 2 4 1 6 molex Audio-Out VGA-Out VGA-In VGA-In / SCART DVI-I S-Video Video RS-232 USB RJ-45 Audio-In Audio-L Audio-R E62405SP R Due to the difference in applications for each country, some regions may have different accessories. 3 1...............................................................................................................Power Cord 2...........................................................
Installation Connect to Video Sources DVD Player, Set-top Box, HDTV receiver 7 6 3 8 4 5 1 Audio-Out VGA-Out VGA-In / SCART VGA-In DVI-I S-Video Video RS-232 USB RJ-45 Audio-In Audio-L Audio-R E62405SP R Due to the difference in applications for each country, some regions may have different accessories. 3 S-Video Output 2 Video Output 1...............................................................................................................Power Cord 2..........................
Installation Powering On/Off the Projector Powering On the Projector 1. Remove the lens cap. 2. Ensure that the power cord and signal cable are securely connected. The Power LED will be Amber. 3. Turn on the lamp by pressing “ON/STANDBY” button either on the top of the projector or on the remote. The Power LED will flash green. The startup screen will display in approximately 10 seconds.
Installation Powering Off the Projector 1. Press the “ON/STANDBY” button to turn off the projector lamp, you will see a message displayed on the projector’s screen. 2. Press the “ON/STANDBY” button again to confirm, otherwise the message will disappear after 15 seconds. When you press the “ON/STANDBY” button a second time, the system will show the countdown timer on the screen. 3. The cooling fans continue to operate for about 10 seconds for cooling cycle.
Installation Adjusting the Projected Image Adjusting the Projector’s Height The projector is equipped with elevator feet for adjusting the image height. To raise the image: 1. Locate the adjustable foot you wish to modify on the underside of the projector. 2. Rotate the four adjustable rings counter clockwise to raise the projector or clockwise to lower it. Repeat with the remaining feet as needed. 3. Reset the projector on its feet and re-adjust as needed.
Installation Adjusting the Projector’s Focus To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 1.6 to 12.1 feet (0.5 to 3.7 meters). Focus Ring Di ag on al Height Adjusting Projection Image Size Width 41.0" (104.2cm) 82.0" (208.3cm) 123.0" (312.5cm) 164.0" (416.7cm) 205.1" (520.8cm) 246.1" (625.0cm) 303.5" (770.8cm) Hd 1.6'(0.5m) 3.3'(1.0m) 4.9'(1.5m) 6.6'(2.0m) 8.2'(2.5m) 9.8'(3.0m) 12.1'(3.7m) Screen (Diagonal) Screen Size Max.
User Controls Control Panel & Remote Control There are two ways for you to control the functions: Control Panel and Remote Control. Using the Control Panel English 8 ON/STANDBY Refer to the “Power On/Off the Projector” section on pages 14-15. Power LED Indicate the projector’s status. Lamp LED Indicate the projector’s lamp status. Temp LED Indicate the projector’s temperature status. Menu Press “Menu” to launch the on-screen display (OSD) menu. To exit OSD, Press “Menu” again.
User Controls Using the Remote Control Model No:RMC-25key Power Refer to the “Power On/Off the Projector” section on pages 14-15. PC/Mouse control The PC/Mouse control can be used to control mouse movement. The mouse function is enabled using the USB cable to connect your computer and the projector. L Button Mouse left click. R Button Mouse right click. Page + Use this button to page up. Page - Use this button to page down. Enter Confirm your item selection.
User Controls Using the Remote Control DVI Press “DVI” to choose DVI-I source. VGA Press “VGA” to choose source from VGA-In connector. AV Mute Momentarily turns off/on the audio and video. S-Video Press “S-Video” to choose S-Video source. Press “Freeze” to pause the screen image. Freeze Press this button again to unlock. Press “Video” to choose Composite video source.
User Controls On-screen Display Menus The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press “Menu” on the Remote Control or Projector Keypad. 2 When OSD is displayed, use keys to select any item in the main menu. While making a selection on a particular page, press or “Enter” key to enter sub menu. 3.
User Controls Menu Tree (*) “Signal” menu is only supported in Analog VGA (RGB) signal.
User Controls Image Display Mode There are many factory presets optimized for various types of images. Presentation: Good color and brightness from PC input. Bright: Maximum brightness from PC input. Movie: For home theater. sRGB: Standardised accurate color. Blackboard: This mode should be selected to achieve optimum color settings when projecting onto a blackboard (green). Classroom: This mode is recommended for projecting in a classroom. User: User’s own settings.
User Controls Image Sharpness Adjust the sharpness of the image. Press the Press the to decrease the sharpness. to increase the sharpness. Image | Color Color Select the Red/Green/Blue Gain for brightness adjustments and Bias for contrast adjustments for the whole picture. Individual color adjustments for Cyan, Magenta, Yellow can also be adjusted. Reset Choose “Yes” to return the factory default settings for color adjustments.
User Controls Image | Advanced Degamma This allows you to choose a degamma table that has been fine-tuned to bring out the best image quality for the input. Film: for home theater. Video: for video or TV source. Graphics: for image source. PC: for PC or computer source. White Peaking This adjustable item utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing true, more vibrant colors in picture. The range is from “0” to “10”.
User Controls Image | Advanced Input Source Enable input sources. Press “ ” into the next menu as below and then use or to select. Press “Enter” to finalize the selection. The projector will not search inputs that are de-selected.
User Controls Display Format Use this function to choose your desired aspect ratio. 4:3: This format is for 4x3 input sources not enhanced for Wide screen TV. 16:9 I: This format is for 16x9 input sources, like HDTV and DVD enhanced for Wide screen TV. (Better format: 576i/p) 16:9 II: This format is for 16x9 input sources, like HDTV and DVD enhanced for Wide screen TV.
User Controls Display area Picture area Input Signal Display on Screen 4:3 format or 16 : 9-I format or 16 : 9-II format window format LBX English 28 format
User Controls Display Overscan Overscan function removes the noise in a video image. Overscan the image to remove video encoding noise on the edge of video source. Zoom Press the Press the to reduce the size of an image. to magnify an image on the projection screen. H Image Shift Shift the projected image position horizontally. V Image Shift Shift the projected image position vertically. V Keystone Press the or squarer image.
User Controls Setup | Language Language Choose the multilingual OSD menu. Press or into the sub menu and then use the or key to select your preferred language. Press “Enter” to finalize the selection.
User Controls Setup Projection Front-Desktop The factory default setting. Rear-Desktop When you select this function, the projector reverses the image so you can project behind a translucent screen. Front-Ceiling When you select this function, the projector turns the image upside down for ceiling-mounted projection. Rear-Ceiling When you select this function, the projector reverses and turns the image upside down at same time.
User Controls Setup Projector ID Allow the RS232 control of an individual projector. Range 00-99. Mute Choose the “On” to turn mute on. Choose the “Off” to turn mute off. Volume Press the Press the to decrease the volume. to increase the volume. RS232 RS232: Allow RS232 control of an individual projector. (Default setting) Network: Allow projector control via web browser (Internet Explorer) using the network.
User Controls Setup | Security Security Settings On: Choose “On” to use security verification when the turning on the projector. Off: Choose “Off” to be able to switch on the projector without password verification. Security Timer Select the time (Month/Day/Hour) function to set the number of hours the projector can be used. Once this time has elapsed you will be requested to enter your password again.
User Controls Setup | Security ■ First Time: 1. The Password is 4 digits, DEFAULT VALUE is “1234”. (first time) 2. Use number buttons on the remote to select your password, and then press “Enter” key to confirm your selection. Change Password 1. Press “Enter” to input old password. 2. Use number button to enter current password, and then press “Enter” key again to reveal next OSD menu. 3. Scroll down to highlight Password, and then press “Enter” to activate. 4.
User Controls Setup | Signal “Signal” menu is only supported in Analog VGA (RGB) signal. Phase Synchronize the signal timing of the display with the graphic card. If you experience an unstable or flickering image, use this function to correct it. Frequency Change the display data frequency to match the frequency of your computer’s graphic card. If you experience a vertical flickering bar, use this function to make an adjustment. H. Position Press the Press the to move the image left.
User Controls Setup | Advanced Logo Use this function to select your desired startup screen. If you change the setting from one to another, when you exit the OSD menu, the new setting will take effect on next open. Optoma: The default startup screen of Optoma projector. Neutral: No logo is displayed.
User Controls Setup | Network Network State To display network information. DHCP Use this function to select your desired startup screen. If you change the setting from one to another, when you exit the OSD menu, the new setting will take effect on next open. On: Assign an IP address to the projector from the DHCP server automatically. Off: Assign an IP address manually. IP Address Select an IP address. Subnet Mask Select subnet mask number.
User Controls How to use web browser to control your projector 1. Fill in a new IP, a subnet mask, a gateway and a DNS in the dialogue box. 2. Then choose apply and press “ configuration process. ” button to effectuate the 3. Open your web browser and type in from the OSD LAN screen then the web page will display as below: When you used the projector IP address, you will can not link to your service server. 4. Open “Control Panel” to control your projector.
User Controls Step 3: To open Network Connections, click Start, click Control Panel, click Network and Internet Connections, and then click Network Connections. Click the connection you want to configure, and then, under Network Tasks , click Change settings of this connection. Step 4: On the General tab, under This connection uses the following items, click Internet Protocol (TCP/IP), and then click “Properties.” Use a proxy server for your LAN check box., then click “OK” button twice.
User Controls Options Source Lock On: The projector will search specified connection port. Off: The projector will search for other signals if the current input signal is lost. High Altitude Choose “On” to turn on High Altitude mode. Operates the fans at full speed continuously to allow for proper high altitude cooling of the projector. Information Hide On: Choose “On” to hide the searching message. Off: Choose “Off” to show the searching message.
User Controls Options | Advanced Direct Power On Choose “On” to turn on Direct Power On mode. The projector will automatically power on when AC power is supplied, without pressing the “ON/STANDBY” key on the projector control panel or “Power” key on the remote control. When Economic Standby (<1W), the VGA out is disabled during standby. Eco. Standby power (<1W) On: Choose “On” to save power dissipation further(<1W). Off: Choose “Off” to return to normal standby mode.
User Controls Options | Lamp Settings Lamp Hours Display the projection time. Lamp Reminder Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will appear 30 hours before suggested replacement of lamp. Brightness Mode STD: Choose “STD” to dim the projector lamp which will lower power consumption and extend the lamp life by up to 130%. BRIGHT: Choose “BRIGHT” to increase the brightness.
Appendices Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. (See pages 55-56 for details) Image Problems No image appears on-screen Ensure all the cables and power connections are correctly and securely connected as described in the “Installation” section. Ensure all the pins of connectors are not bent or broken.
Appendices 6. Select the “Change” button under the “Monitor” tab. 7. Click on “Show all devices”. Next, select “Standard monitor types” under the SP box; choose the resolution mode you need under the “Models” box. (*) The resolution XGA (1024 x 768) is recommended for computer signal. 8. Verify that the resolution setting of the monitor display is lower than or equal to UXGA (1600 x 1200). (*) If you are using a Notebook: 1. First, follow the steps above to adjust resolution of the computer. 2.
Appendices Image has vertical flickering bar Use “Frequency” to make an adjustment. See page 35 for more information. Check and reconfigure the display mode of your graphic card to make it compatible with the projector. Image is out of focus Make sure the lens cap is removed. Adjusts the Focus Ring on the projector lens. Make sure the projection screen is between the required distance 1.6 to 12.1 feet (0.5 to 3.7 meters) from the projector. See page 17.
Appendices Intermission Problems The projector stops responding to all controls If possible, turn off the projector, then unplug the power cord and wait at least 60 seconds before reconnecting power. Lamp burns out or makes a popping sound When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced.
Appendices Message Reminders Fan failed: Temperature warning: Lamp Warning: Source Message: Remote Control Problems If the remote control does not work Check the operating angle for the remote control is approximately ±22.5°. Make sure there are no obstructions between the remote control and the projector. Move to within 6 m (20 ft) of the projector. Make sure the batteries are inserted correctly. Replace weak batteries in the remote control.
Appendices Replacing the lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp. CAUTION! Hg HIGH TEMPERATURE COOL FOR 30 MINUTES. HIGH PRESSURE LAMP MAY EXPLODE IF IMPROPERLY HANDED.
Appendices 1 2 4 3 5 Lamp Replacement Procedure: 1. 2. 3. 4. 5. 6. 7. Switch off the power to the projector by pressing the “Power” button. Allow the projector to cool down for at least 30 minutes. Disconnect the power cord. Use a screwdriver to unscrew the 2 screws from the cover. Push up and remove the cover. Use a screwdriver to unscrew the 2 screws from the lamp module. Pull up the lamp handle carefully. 8. Remove the lamp module.
Appendices Compatibility Modes Computer Compatibility V-Sync (Hz) Mode Resolution VGA 640 x 350 VGA 640 x 400 85 85 VGA 640 x 480 60, 72, 75, 85 60, 72, 75, 85 Analog Digital 70, 85 70, 85 VGA 720 x 400 70, 85 70, 85 SVGA 800 x 600 56, 60, 72, 75, 85 56, 60, 72, 75, 85 XGA 1024 x 768 60, 70, 75, 85 60, 70, 75, 85 SXGA 1152 x 864 70, 75, 85 70, 75, 85 SXGA 1280 x 1024 60, 75, 85 60, 75, 85 SXGA+ 1400 x 1050 60 60 UXGA 1600 x 1200 60 60 MAC LC 13” 640 x 480 66.
Appendices RS232 Commands RS232 Pin Assignments 3 1 2 9 5 8 4 7 3 6 2 Pin no. Spec. 1 N/A 2 RXD Name I/O (From Projector Side) 1 TXD OUT 3 TXD 2 RXD IN 4 N/A 3 GND __ 5 GND 6 N/A 7 N/A 8 N/A 9 N/A Pin no.
Appendices RS232 Protocol Function List RS232 Commands Baud Rate : 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control : None UART16550 FIFO: Disable Projector Return (Pass): P Projector Return (Fail): F XX=01-99, projector's ID, XX=00 is for all projectors 1. There is a after all ASCII commands. 2. 0D is the HEX code for in ASCII code.
Appendices SEND to projector ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code Function Description ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX73 n 7E 30 30 37 33 20 a 0D Sig
Appendices Ceiling Mount Installation 1. To prevent damaging your projector, please use the Optoma’s recommended mount package for installation. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attached a mount to the projector met the following specifications: Screw type: M4 Please note that damage resulting from incorrect installation will invalidate the warranty. Warning: 1.
Appendices Optoma Global Offices For service or support please contact your local office. USA 715 Sycamore Drive Milpitas, CA 95035, USA www.optomausa.com Tel : 408-383-3700 Fax : 408-383-3702 Service : services@optoma.com Canada 5630 Kennedy Road, Mississauga, ON, L4Z 2A9, Canada www.optoma.ca Tel : 905-361-2582 Fax : 905-361-2581 Europe 42 Caxton Way, The Watford Business Park Watford, Hertfordshire, WD18 8QZ, UK Tel : +44 (0) 1923 691 800 www.optoma.
Appendices Korean WOOMI TECH.CO.,LTD. 4F,Minu Bldg.33-14, Kangnam-Ku, Tel : +82+2+34430004 seoul,135-815, KOREA Fax : +82+2+34430005 Japanese 東京都足立区綾瀬3-25-18 株式会社オーエスエム サポートセンター:0120-46-5040 Taiwan 5F., No. 108, Minchiuan Rd. Shindian City, Taipei Taiwan 231, R.O.C. www.optoma.com.tw E-mail : info@osscreen.com www.os-worldwide.com Tel : +886-2-2218-2360 Fax : +886-2-2218-2313 Service : services@optoma.com.tw asia.optoma.
Appendices Regulation & Safety notices This appendix lists the general notices of your projector. FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendices Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003.
