Installation Guide HDBV3100, HDBV3090, HDBV3080
Installation Guide HDBV3100, HDBV3090, HDBV3080 BigVizion In-Wall Rear Projection Display Optoma’s BigVizion is an in-wall modular rear projection display consisting of a framing system, system control components, a mirror, screen frame assembly and DLP® light engine. The BigVizion is a modular designed system and offers front access to all components through a movable front screen frame assembly.
Installation Guide HDBV3100, HDBV3090, HDBV3080 About this Manual This manual exclusively describes the set-up and use of Optoma’s in-wall rear projection displays.
Installation Guide HDBV3100, HDBV3090, HDBV3080 FCC WARNING This equipment has been tested and found to comply with the limits for a “Class B” digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Installation Preparation WARNING: All installations must be performed in accordance with standard utility practice; The National Electric Code, The National Electric Safety Code, The Local Electric Code, and any local city ordinances that may apply to building construction and/or modification to residential structures.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Contents Section I: Preparation for the Installation 1) Position and Placement of the BigVizion 2) Preparing the Wall 3) Shipment of Box 1 (Master Outer Frame) to Job Site 4) Master Outer Frame Assembly 5) Installation of the Master Outer Frame Section II: Installation of the Frame Components 1) Shipment of the Internal Frame Components to the Job Site 2) Unpacking the Mirror 3) Installation of the Mirror 4) Unpacking of the Base Unit Components 5) Assembly
Installation Guide HDBV3100, HDBV3090, HDBV3080 Section I: Preparation for the Installation 1. Position and Placement of the BigVizion Wall selection is crucial in the BigVizion installation for producing the desired image quality. The BigVizion may be installed during new home construction or aftermarket remodels. New home construction lends itself to better placement, since the BigVizion could be implemented during the design phase.
Installation Guide HDBV3100, HDBV3090, HDBV3080 2. Preparing the Wall For new home construction, the roughing stage to the final installation may take several months. The BigVizion packaging has been designed for the master frame (Outer Master Frame) to be installed during the roughing stage. Follow the listed steps for installation: Wall Preparation: Step 1: The location of the installation will be determined by environmental factors such as wall depth, lighting and ideal viewing heights.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Step 2: Cut a rough opening through the wall at the correct height, so when finished with the standard 2" x 4" wood framing, the opening corresponds to the following dimensions: • BVHD3100 (100"), the rough wall opening must measure at least: 91-11/16" W x 54-13/16" H. 100" BigVizion Wall Opening Diagram. (Figure 1-1) • BVHD3090 (90"), the rough wall opening must measure at least: 83" W x 50" H. 90" BigVizion Wall Opening Diagram.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 1-1: 100" BigVizion Wall Opening For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 1-2: 90" BigVizion Wall Opening For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 1-3: 80" BigVizion Wall Opening For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 3. Shipment of Box 1 (Master Outer Frame) The master outer frame is located in a knock down box as part of the master BigVizion shipment module. Unscrew the box from the shipment module and bring to the installation site during the roughing stage of the construction. Step 1: Carefully unpack the master outer frame; two vertical and two horizontal pieces. See Figure 1-4: Box #1 Detail Notice each piece is marked left, right, top and bottom.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 1-4: Box #1 Detail For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 4. Assembly of the Master Outer Frame Step 1: Locate the eight #10-32 screws with washers. Step 2: Insert two #10-32 screws with washers on each corner to assemble frames; left, right, top and bottom. IMPORTANT! See Figure 1-5: Installation of the Master Frame Diagram. For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 1-5: Installation of the Master Frame For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Installation of the Master Outer Frame into the Wall Opening Step 1: With a minimum of two people, carefully raise the master outer frame from the smooth surface while supporting the frame on the left and right side. IMPORTANT! Exercise caution when raising the frame. Step 2: Position the frame in the wall opening. Step 3: Make certain that the frame is positioned, squared and flushed in the wall opening.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 1-6: Installation of the Master Frame into the Wall Opening For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Section II: Installation of the Frame Components 1. Shipment of the Internal Frame Components to the Job Site Once the outer master frame has been installed, have the remainder of the framing components available at the installation site. This includes the internal framing components and all electronics. 2. Unpacking the Mirror Step 1: Make certain that there are at least three people available for the unpacking and installation of the mirror.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 2-1: Exploded View of the Mirror and the Frame For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 3. Installation of the Mirror To install the mirror, have two people lift the mirror, as well as a safety person to guide the mirror. Carefully move the mirror through either a side opening or a rear opening in the wall behind the master outer frame. Slide the shoulder bolt that is on the top left side of the mirror through the slot on the left top of master frame, and repeat this with the right side. See Figure 2-2: Installation of the Mirror Assembly.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 2-2: Installation of the Mirror Assembly. For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 4. Unpacking of Base Unit and Components Step 1: Locate Box 2. Refer to Figure 2-3: The Unpacking Diagram. Step 2: Remove the screws with red washers, and remove the lid on the crate.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Step 6: Organize the mirror stay arms, base hangers, stabilizer arms, gage blocks and hardware. Step 7: Locate the two mirror stay arms. Note the orientation arrow for this end up, as well as the one end marked S to denote pointing towards the screen or front of the wall. Step 8: Working from inside the wall space, attach the front of the mirror stay arm (S) towards the screen/wall to the bottom portion of the master outer frame.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 2-3: The Unpacking Diagram For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 2-4: Box 2 Detail For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 5. Assembly of the Base Unit Step 1: Locate the base unit and the two base hangers that were set aside. (Refer back to Figure 2-4: Box 2 Detail.) Step 2: Carefully lift the bottom of the base unit by lifting the left and right side. Attach the base hangers as shown in Figure 2-5: Installation of the Projector Base. (Note the orientation of the base hangers; (S) for towards the front/screen and (M) towards the back/mirror.
Installation Guide HDBV3100, HDBV3090, HDBV3080 6. Installation of the Base Unit Step 1: Working from the front of the wall opening with a minimum of two people, carefully raise the base unit. Step 2: Position the base hangers to the outside of the mirror stay arms. Step 3: Insert four 5/16-18 x ¾" screws with washers through the two middle holes on the mirror stay arms. Note: Washers need to be inserted on both the inside and outside of the mirror stay arms.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 2-5: Installation of the Projector Base. For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 7. Installation of the Screen Frame Step 1: Locate box 3 that the mirror was removed from. (Refer back to the master crate.) Step 2: Remove the two side panels that attach box 3 to the bottom of the crate. (Necessary to access box 4) Step 3: On the left and right side panel, only remove the screws with red washers that secures box 3 to the master crate. Step 4: Carefully remove box 3 from the crate and set it aside; it is no longer needed.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Step 9: The screen frame has two sides. The back side has ridges and circles; while the front side is smooth with a plastic wrap. Step 10: Notice that the screen frame has two pins on each side; the left and right. Step 11: If you are facing the front of the outer master frame, it has a hole on the top left side and a slot on the top right side. Step 12: With two people, lift the screen frame up with the glossy side facing out.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 2-6: Installation of the Screen For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 8. Installation of the Wood Bezel Locate the wood bezel that was set aside during the screen frame assembly. Use the following steps to install the bezel. Step 1: With two people, carefully orient the wood bezel vertically. Step 2: Align the six grabber catches, the female part of the bezel clip and the male part of the main frame. Step 3: Position the bezel so the bottom arrows on the bezel align with the bottom arrows on the master outer frame.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 2-7: Installation of the Wood Bezel For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Section III: Alignment of the Light Engine ALIGNMENT PLATFORM ADJUSTMENT PROCEDURE Use the Video Essentials or Avia Test DVD for alignment patterns. Step 1: Using two gage blocks for initial positioning, adjust the alignment platform (AP) until the bottom of AP surface contacts the gage blocks and the rear edge of both the AP and the projection base (PB) contacts the corners of the gage blocks. See Figure 3-1: Setting the Gage on “0” Position.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Figure 3-1: Setting the Gage on “0” Position For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Problem: (Vertical Keystone) Solution: Turn knobs #1 & 4 together in the same direction. Figure 3-2: Vertical Keystone Adjustment VERTICAL KEYSTONE For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Problem: (Horizontal Keystone) Solution: Turn knobs #3 & 4 together in the same direction. Figure 3-3: Horizontal Keystone Adjustment HORIZONTAL KEYSTONE For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Problem: (Skewed Image) Solution: Turn knobs #5 & 6 in opposite directions. Figure 3-4: Skewed Image Adjustment SKEWED PICTURE For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Problem: (Image Shift Vertically) Solution: Turn knobs #5 & 6 in the same direction. Figure 3-5: Image Shift Vertically Adjustment IMAGE SHIFT VERTICALLY For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Problem: (Image Shift Horizontally) Solution: Loosen the four Philips head screws just enough to manually shift AP to the left or right and then tighten the screws. Figure 3-6: Image Shift Horizontally Adjustment IMAGE SHIFT HORIZONTALLY For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Problem: (Image Sizing) Solution: Turn knobs #1, 2, 3 & 4 in the same direction. Figure 3-7: Image Sizing Adjustment IMAGE SIZING For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Appendix A: Cable Wiring/Connections Cables: For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Connectors: Ballast Cable For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Connectors: (Continued) For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Instructions: Connectors SC2, SC3, SC7, SC10 and SC11 are connected at the factory. To connect the rest of the cables, follow the procedures below. NOTE: Cables 3 through 7 each have two different ends and only fit in their proper locations in one orientation. Do not force any of the cables in if they do not fit. Doing so may damage the cables and/or their respective housings.
Installation Guide HDBV3100, HDBV3090, HDBV3080 HDMI out HDMI HD3000 DVI System Command Board 12V Cable 1 14-pin Cable 2 Cable 3 TS 12V Fan1 Fan2 Cable 4 Cable 4 Cable 5 Cable 6 Cable 7 LE Power DVI L/E Bottom TS Lamp Fan Engine Side DMD Fan For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 Appendix B: Discrete IR/RS-232C Codes HD3000 RS-232C Protocol Function List Function List Interface Power On Function Description Basic(Original) *0IR001 Power Off *0IR002 Menu *0IR003 3 wires RS-232C Protocol Baud Rate : 57600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control :None Command Sequence Up *0IR004 Down *0IR005 Left *0IR006 Right *0IR007 Enter *0IR008 Re-Sync *0IR009 Source-CVB1 *0IR01
Installation Guide HDBV3100, HDBV3090, HDBV3080 HD3000 RS-232C Protocol Function List (Continued) Source-HDMI1 Function Description Basic(Original) *0IR020 Source-HDMI2 *0IR021 Source-HDMI3 *0IR022 Source-VGA *0IR023 Aspect Ratio- 16:19 *0IR024 Aspect Ratio- 4:3 *0IR025 Aspect Ratio- Native *0IR026 Aspect Ratio- Format1 *0IR027 Aspect Ratio- Format2 *0IR028 Aspect Ratio- Format3 *0IR029 Model-ISF Day *0IR030 Model-ISF Night *0IR031 M
Installation Guide HDBV3100, HDBV3090, HDBV3080 Appendix C: Exploded View of the Product For more information, please visit our website at: http://www.optomausa.
Installation Guide HDBV3100, HDBV3090, HDBV3080 For more information, please visit our website at: http://www.optomausa.
Canada 5630 Kennedy Road Mississauga, ON, L4Z 2A9 Tel: 905-882-4228 Fax: 905-882-4229 www.optoma.ca USA 715 Sycamore Drive Milpitas, CA 95035 Tel: 408-383-3700 Fax: 408-383-3702 www.optomausa.com Optoma Technology, Inc. 715 Sycamore Drive, Milpitas, CA 95035 · Tel: (408) 383-3700 · Fax: (408) 383-3702 Specifications subject to change without notice. Copyright © 2006 Optoma Technology, Inc. All rights reserved.
