User’s Manual OPT-6125 Series Handheld CCD Scanner 25-ULGPMU01-01 April 2002 Keyboard Wedge Interface USB Interface RS232 Interface 8 Olympic Drive Orangeburg, NY 10962 Tel 845.365.0090 Fax 845.365.1251 www.opticonUSA.
Manual No. 25-ULGPMU01-01 Series OPT Handheld CCD Scanner Table of Contents PART I CCD Scanning General Information ...........................................4 Unpacking Factory Technical Support Part II Installation and SetUp A. Installation –Wedge Interface ……………5 Reset all Defaults …………………………………………….6 Computer Type Selection … ............................... 6 InterCharacter Delay ..........................................7 Part III Bar Code Menu Functions Section A Programming the Scanner……………..
Manual No. 25-ULGPMU01-01 Series OPT Handheld CCD Scanner Part I General Information The OPT-6125 Series CCD Scanners utilize state-of-the-art imaging technology similar to that found in digital cameras, facsimile machines and video camcorders. The scanner images the bar code label, then converts the digital signals into data the host computer can understand. By capturing the bar code image all at once, the scanner provides fast, highly accurate reading.
Manual No. 25-ULGPMU01-01 Series OPT Handheld CCD Scanner Part II Installation and SetUp This section of the manual contains information on the physical installation of the scanner as well as certain programming options. There is a separate section for each type of interface. Check to see which type of interface your scanner has and turn to that section for information on installing the scanner A.) Installation – Keyboard Wedge Interface A "Y" connection cable is required for installation.
Manual No. 25-ULGPMU01-01 Series OPT Handheld CCD Scanner Reset All Defaults – Keyboad Wedge Interface Our scanners are shipped with factory default settings that represent the settings most commonly used by our customers. In most applications, the scanner will work right out of the box without any need for additional programming. At any time you can return the scanner to the factory default settings by scanning the “Reset all Defaults” programming bar code below.
Manual No. 25-ULGPMU01-01 Series OPT Handheld CCD Scanner Intercharacter Delay for Keyboard Wedge interface The scanner may send data faster than the computer or application program can accept. This is called "keyboard buffer overrun". If data appears to be missing, random read errors occur or the scanner locks up and will not scan, experiment with the various keyboard timing options listed in the menu to follow.
Manual No. 25-ULGPMU01-01 Series OPT Handheld CCD Scanner B.) Installation – RS232 Interface The RS-232 scanner cable is terminated in with a DB9 female connector. An external power supply (+5V DC) may be necessary. There is a power supply jack on the RS-232 connector. Installation is as follows: 1. Plug the scanner into an RS232 serial port (such as COM1) of the host PC. If external power is required, insert external power plug into the jack on the RS-232 connector. 2.
Manual No.
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld C.) Installation – USB Interface Plug the scanner into the USB connector on your host computer. PC must be running Windows 98 or higher or iMac Rev A or higher. The computer will sense the presence of the scanner and load any required software drivers automatically. Reset All Defaults - USB Interface Our scanners are shipped with factory default settings that represent the settings most commonly used by our customers.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Part III Bar Code Menu Functions Section A Programming the Scanner This manual contains information that allows you to easily change certain programmable parameters of the scanner. The scanner is ready to use - no additional programming is required in most situations. The scanner has been programmed at the factory with the most common settings. These factory default settings are ideal for most situations.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Symbology Selection ZZ Start/End Program Menu A0 Read all codes A2 Code 39 only A3 Codabar only -B!- A4 IATA only -B5- A5 Code 93 only -B6- A6 Code 128 only -B7- A7 MSI/Plessey only -B8- A9 Telepen only -B:- AB Matrix 2of5 only -BC- J0 All UPC and EAN only -K1- J1 UPC only -K2- -[[-B1- Β -B3- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Symbology Selection (continued) ZZ Start/End Program Menu -[[- J2 UPC+2 only -K3- J3 UPC+5 only -K!- J4 EAN only -K5- J5 EAN+2 only -K6- J6 EAN+5 only -K7- J7 Industrial 2of5 only -K8- J8 Interleaved 2of5 only -K9- JD Trioptics only -KE- These options do not influence the reading of the menu labels.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Symbology Additions If scanner will not be used to read all symbologies (default setting), speed operation by using this menu to add only the specific symbologies being used (add only the symbologies that are required).
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Setting the Number of Characters to be Scanned ZZ Start/End Program Menu -[[- H0 Fixed length OFF all codes H1 Fixed length ON all codes -I1- Β -I2- HK Fixed length ON selected codes -IL- HL Min. length selected codes -IM- HM Max. length selected codes -IN- Setting Code Specific Options - Options for specific codes may be configured affecting: * Enabling and disabling code variants and translations.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld UPC Settings Options for UPC-A and UPC-E bar codes.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld UPC Settings (continued) Options for UPC-A - The UPC-A symbology is a fixed length symbology encoding 11 data digits, a check digit and non printable start/stop characters. Supported characters are numeric digits 1 to 9. An optional leading zero can be transmitted which, together with the data and the check digit, forms a 13 digit field providing compatibility with the EAN-13 format.
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld EAN-13 and EAN-8 Settings EAN-13 is a fixed length symbology encoding 12 data digits, a check digit and non printable start/stop characters. Supported characters are numeric digits 0 to 9. The data may be translated into ISBN or ISSN format. String format: data check digit (12 digits) EAN-13 add-on 2/add-on 5 - The EAN-13 symbology as described above can be succeeded by an additional 2 or 5 digit UPC-A code.
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld 8D Minimum 3 digits -9E- 8E Minimum 1 digit -9F- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Code 39 Settings (continued) Code 39 is a variable length symbology with an optional check digit ("CD") and printable start/stop ("ST/SP") characters. The following characters are supported: • Numeric characters 0 to 9 • Alpha characters capital A to Z • Special characters - $ / + % and SPACE • Start/stop character is * The checksum is calculated as the sum modulo 43 of the numerical value of the data characters.
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Codabar Settings (continued) ZZ Start/End Program Menu -[[- HA Enable Codabar normal mode only -IB- % HB Min. data 3 chars. -IC- HC Min. data 1 char. -ID- HD Enable space insertion -IE- HE Disable space insertion -IF- % HF Min. data 5 chars. -IG- % HH Enable interchar. gap check -II- % HI Disable interchar.
Manual No. 25-ULGPMU01-01 CCD Scanner * Series OPT Handheld start/stop characters are A, B, C or D The checksum is calculated as the sum modulo 16 of the numerical values of all data characters. String format: start char. data (1 or more chars.) check digit stop char. CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Codabar Settings (continued) Series OPT Handheld ABC-Code - The ABC code is an acronym for American Blood Commission. The code consists of two bar codes which are decoded in one read cycle. the code is concatenated when the stop character of the first bar code and the start character of the second bar code is a D. These two D's are not transmitted. String format: start data (1+ check data (1+ check stop char. chars.) digit chars.) digit char.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld 2of5 Settings ZZ Start/End Program Menu E0 Transmit CD E1 Do not transmit CD G0 Do not check CD -H1- % G1 Check CD -H2- GE Min. data 1 char. -HF- GF Min. data 3 chars. -HG- GI Min. data 5 chars. -GJ- % GJ Enable space check for Industrial 2of5 -GK- % GK Disable space check for Industrial 2of5 -HL- -[[-F1- % -F2- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner 2of5 Settings (continued) Series OPT Handheld Code 2of5 is a variable length symbology with an optional check digit and non printable start and stop character. Supported characters include numeric digits 0 to 9. The checksum is calculated as the sum modulo 10 of the numerical values of all the data characters. The following 2of5 codes are supported.
Manual No.
Manual No. 25-ULGPMU01-01 Series OPT Handheld CCD Scanner Check digit - If the check digit calculation is required, then the appropriate calculation method must be selected. Do not transmit CD - The character positions CD1 and CD2 are not transmitted. Transmit CD1 - The character position CD2 is not transmitted. Transmit CD1 and CD2 - All characters in the label are transmitted.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Code 128, EAN 128 Settings ZZ Start/End Program Menu -[[- JF Enable EAN 128 only -KG- MO Enable FNC2 concat-enation -NP- MP Disable FNC2 concat-enation -NQ- % OF Disable EAN 128 -PG- % OG Enable EAN 128 if possible -PH- Code 128 is a variable length symbology with a mandatory check digit and non-printable start/stop characters.
Manual No. 25-ULGPMU01-01 Series OPT Handheld CCD Scanner FNC2 Concatenation - If a Code 128 bar code contains a leading FNC2 character, the data is stored into the reader's buffer. As soon as a Code 128 bar code is read without a leading FNC2 character, the data is appended to the reader's buffer and the entire buffer is transmitted and cleared for new data. In case a non Code 128 bar code is read, the data in the non-Code 128 bar code is transmitted and the buffer is cleared.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld IATA Settings ZZ Start/End Program Menu 4H Do not check CD 4I Check S/N only -5J- 4J Check CPN, S/N -5K- 4K Check CPN, airline and S/N -5L- 4L Transmit CD -5M- % 4M Do not transmit CD -5N- -[[-!5I- % IATA is a variable length symbology with an optional check digit and non printable start/stop characters. Supported characters include numeric digits 0 through 9. The checksum is calculated as the modulo seven of the data string.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Telepen Settings ZZ Start/End Program Menu D2 Numeric mode D3 ASCII mode -[[-E3- % -E!- Telepen is a variable length symbology with a check digit and non printable start/stop characters. Supported characters include numeric digits 00 through 99 in numeric mode, and all 128 ASCII characters in full ASCII mode. The check digit calculation is derived from the sum of all data characters modulo 127. The check digit cannot be transmitted.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Case Conversion ZZ Start/End Program Menu -[[- YZ No case conversion -Z[- % YW Convert to upper case -ZX- YX Convert to lower case -ZY- YY Exchange case -ZZ- String Options - This section describes the alterations which can be made to the format of the transmitted data string.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Setting a Prefix or Suffix A Prefix and Suffix consisting of a maximum 4 direct input entries each may be included in front and at the end of the string, respectively. The following steps are used to establish a Prefix or Suffix that will be transmitted with the bar code data. 1) Scan Start/End Program Menu to enter programming mode. 2) Scan the bar code representing the desired symbology you wish to add a Prefix or Suffix to.
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Suffix Settings ZZ Start/End Program Menu -[[- GM Matrix 2of5 -HN- I9 IATA -J:- L9 Telepen -M:- N5 MSI/Plessey -O6- N6 UPC-A -O7- N7 UPC-E -O8- N8 EAN-13 -O9- N9 EAN-8 -O:- O0 UPC-A + add-on -P1- O1 UPC-E + add-on -P2- O2 EAN-13 + add-on -P3- O3 EAN-8 + add-on -P!- O4 Code 39 -P5- O5 Codabar -P6- CONTINUED ON NEXT PAGE...
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Direct Input Keyboard Keys ZZ Start/End Program Menu -[[- 8J F1 -9K- 8K F2 -9L- 8L F3 -9M- 8M F4 -9N- 8N F5 -9O- 8O F6 -9P- 8P F7 -9Q- 8Q F8 -9R- 8R F9 -9S- 8S F10 -9T- 8T F11 -9U- 8U F12 -9V- 9X Backspace -:Y- 7H TAB -8I- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Direct Input Keyboard Keys (continued) Series OPT Handheld ZZ Start/End Program Menu 7I Carriage return 7Q Enter (numeric pad) -8R- 7R Enter make (alpha pad) -8S- 7S Enter make and break (alpha pad) -8E- 7J ESC -8K- 7K Arrow down -8L- 7L Arrow up -8M- 7M Arrow right -8N- 7N Arrow left -8O- 7T -8U- VQ -WR- VR -WS- VS -WT- 7O Page up -8P- -[[-8J- % CONTINUED ON NEXT PAGE...
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Direct Input Characters ZZ Start/End Program Menu -[[- 5A -6B- 5B ! -6C- 5C " -6D- 5D # -6E- 5E $ -6F- 5F % -6G- 5G & -6H- 5H ' -6I- 5I ( -6J- 5J ) -6K- 5K * -6L- 5L + -6M- 5M , -6N- 5N - -6O- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Direct Input Characters (continued) Series OPT Handheld ZZ Start/End Program Menu -[[- 5O . -6P- 5P / -6Q- 6A : -7B- 6B ; -7C- 6C < -7D- 6D = -7E- 6E > -7F- 6F ? -7G- 6G @ -7H- 7A [ -8B- 7B \ -8C- 7C ] -8D- 7D ^ -8E- 7E _ -8F- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Direct Input Characters (continued) Series OPT Handheld ZZ Start/End Program Menu -[[- 7F ` -8G- 9T { -:U- 9U | -:V- 9V } -:W- 9W ~ -:X- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Direct Input Characters (continued) Series OPT Handheld ZZ Start/End Program Menu -[[- Q0 0 -R1- Q1 1 -R2- Q2 2 -R3- Q3 3 -R!- Q4 4 -R5- Q5 5 -R6- Q6 6 -R7- Q7 7 -R8- Q8 8 -R9- Q9 9 -R:- 0A A -1B- 0B B -1C- 0C C -1D- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Direct Input Characters (continued) Series OPT Handheld ZZ Start/End Program Menu -[[- 0D D -1E- 0E E -1F- 0F F -1G- 0G G -1H- 0H H -1I- 0I I -1J- 0J J -1K- 0K K -1L- 0L L -1M- 0M M -1N- 0N N -1O- 0O O -1P- 0P P -1Q- 0Q Q -1R- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Direct Input Characters (continued) Series OPT Handheld ZZ Start/End Program Menu -[[- 0R R -1S- 0S S -1T- 0T T -1U- 0U U -1V- 0V V -1W- 0W W -1X- 0X X -1Y- 0Y Y -1Z- 0Z Z -1[- $A a -%B- $B b -%C- $C c -%D- $D d -%E- $E e -%F- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Direct Input Characters (continued) Series OPT Handheld ZZ Start/End Program Menu -[[- $F f -%G- $G g -%H- $H h -%I- $I i -%J- $J j -%K- $K k -%L- $L l -%M- $M m -%N- $N n -%O- $O o -%P- $P p -%Q/ $Q q -%R- $R r -%S- $S s -%T- CONTINUED ON NEXT PAGE...
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Direct Input Control Characters ZZ Start/End Program Menu -[[- 9G ^@(NULL) -:H- 1A ^A(SOH) -2B- 1B ^B(STX) -2C- 1C ^C(ETX) -2D- 1D ^D(EOT) -2E- 1E ^E(ENQ) -2F- 1F ^F(ACK) -2G- 1G ^G(BEL) -2H- 1H ^H(BS) -2I- 1I ^I(HT) -2J- 1J ^J(LF) -2K- 1K ^K(VT) -2L- 1L ^L(FF) -2M- 1M ^M(CR) -2N- CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Direct Input Control Characters (continued) Series OPT Handheld ZZ Start/End Program Menu -[[- 1N ^N(SO) -2O- 1O ^O(SI) -2P- 1P ^P(DLE) -2Q- 1Q ^Q(DC1) -2R- 1R ^R(DC2) -2S- 1S ^S(DC3) -2T- 1T ^T(DC4) -2U- 1U ^U(NAK) -2V- 1V ^V(SYN) -2W- 1W ^W(ETB) -2X- 1X ^X(CAN) -2Y- 1Y ^Y(EM) -2Z- 1Z ^Z(SUB) -2[- 9A ^[(ESC) -:B- CONTINUED ON NEXT PAGE...
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Read Mode Settings ZZ Start/End Program Menu -[[- S0 Single read -T1- S1 Multiple read S2 Continuous read -T3- XA Add-on wait mode disabled -YB- XB Add-on wait mode 0.25 sec. -TC- XC Add-on wait mode 0.50 sec. -YD- % XD Add-on wait mode 0.70 sec. -YE- -T2- % Single Read - When a bar code has been decoded, the reader will be turned OFF. The reader must be triggered again to read another label.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Trigger Settings ZZ Start/End Program Menu -[[- S7 Disable trigger -T8- S8 Enable trigger -T9- Disable Trigger - This is applicable to readers which have a trigger switch. When this option is selected, the reader will stay ON all the time.
Manual No.
Manual No.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Redundant Decoding Settings ZZ Start/End Program Menu -[[- X0 No redundancy -Y1- X1 Two times redundant -Y2- % X2 Three times redundant -Y3- X3 Four times redundant -Y!- Redundancy Settings - This is the number of times that a label must be correctly decoded before it is transmitted.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Buzzer Settings ZZ Start/End Program Menu W8 Enable software buzzer -X9- % W0 Disable buzzer -X1- W1 Single tone buzzer -X2- W2 High - low buzzer -X3- % W3 Low - high buzzer -X!- W7 Buzzer duration 50 msec. -X8- W4 Buzzer duration 100 msec. -X5- W5 Buzzer duration 200 msec. -X6- % W6 Buzzer duration 400 msec.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld T2 Buzzer volume normal -U3- T3 Buzzer volume minimum -U!- VY Buzzer before transmission -WZ- % CONTINUED ON NEXT PAGE...
Manual No. 25-ULGPMU01-01 CCD Scanner Buzzer Settings Series OPT Handheld ZZ Start/End Program Menu -[[- VZ Buzzer after transmission -W[- GD Disable startup buzzer -HE- GC Enable startup buzzer -HD- Buzzer Settings - These options determine the buzzer type, tone, duration and loudness. By default, the buzzer is disabled for Linker type readers. Buzzer Type - The buzzer may be disabled or enabled as either a hardware of software buzzer.
Manual No. 25-ULGPMU01-01 CCD Scanner Series OPT Handheld Good Read LED ZZ Start/End Program Menu -[[- T4 Disable indicator -U5- T5 Indicator duration 0.2 sec. -U6- % T6 Indicator duration 0.4 sec. -U7- T7 Indicator duration 0.8 sec. -U8- ZZ Start/End Program Menu -[[- Z1 Transmit software version -[2- Z3 Transmit settings -[!- ZA Transmit ASCII printable string YV Transmit ASCII control string -ZW- TH Error msg. label -UI- TI Error msg.
