User’s Manual Wand Terminal DWT 7133 Cradle DCW 9931
USER’S MANUAL DWT 7133 USER’S MANUAL DWT 7133 CONTENTS page INTRODUCTION 3 1. 1.1 1.2 1.3 1.4 1.5 THE DWT7133 Components DWT7133 Cradle DCW9931 Terminal on cradle Characteristics of the DWT7133 Battery charging 4 4 4 5 6 6 2. 2.1 2.2 2.2.1 2.2.2 INSTALLATION AND STARTUP Power supply Connecting cradle to host Serial mode (RS232 interface) Network mode (RS485 interface) 8 8 8 9 9 Limited warranty and disclaimers 3.
USER’S MANUAL DWT 7133 USER’S MANUAL DWT 7133 1.1 COMPONENTS DWT 7133 1.3 TERMINAL ON CRADLE 1. Reading Tip An optical reader for bar codes. 2. Activation key definable by user’s application Typical use: Enables the user to activate the bar code reader. THE DWT7133 Before you begin your installation, be certain that you have all the items listed below: This manual. The DWT7133 pen terminal. If ordered: The DCW9931 cradle (including powercable) If ordered: Connection cables.
USER’S MANUAL DWT 7133 USER’S MANUAL DWT 7133 1.4 CHARACTERISTICS OF THE DWT 7133 User programmable The DWT7133 is user programmable with the C-programming language (ordered as C-library and C-compiler). It enables you to develop and upload data storage and data processing applications conforming to your own requirements and preferences. 1.5 BATTERY CHARGING ! Supports all popular bar code symbologies Auto discrimination among all popular bar code symbologies.
USER’S MANUAL DWT 7133 USER’S MANUAL DWT 7133 2.2.1 2.1 POWER SUPPLY 3 2 INSTALLATION AND STARTUP This chapter will provide instructions on how to install the DCW9931 cradle and the DWT7133 terminal. The flexibility of the DCW9931 cradle allows you to use the DWT7133 terminal in two modes: Single mode: A single cradle is connected to a serial port of a host computer. Network mode: Several cradles are connected to a single serial port of a host computer.
USER’S MANUAL DWT 7133 3 3 USER’S MANUAL DWT 7133 READING BAR CODES WITH DWT7133 3 4 OPERATION OF THE TERMINAL 4.1 The functionality of the terminal is determined by software, the so-called user application, that is running on the terminal. Holding the DWT7133 1. Hold the terminal lightly in your hand as if it were a normal pen. 2. Keep it slightly inclined with respect to its bar code-supporting surface (approximately 5 degrees). 3. The wand tip must emit red light.
USER’S MANUAL DWT 7133 USER’S MANUAL DWT 7133 Reading angle 0 - 45 o in all directions Resolution at PCS 0.9 0.15 mm (6 mil) Min. PCS value 0.3 5.1.3 3 5 TECHNICAL SPECIFICATIONS 5.1 DWT7133 TERMINAL 5.1.1 Electrical specifications Main battery NI-MH rechargeable Main battery operating time When making every 5 seconds 1 scan with 1 sec reading LED on and 0.2 sec. green LED on and 0.2 sec. buzzer on, operating time is: approx.
USER’S MANUAL DWT 7133 3 A USER’S MANUAL DWT 7133 3 B PINOUT DESCRIPTION This appendix contains the pinout description of the connection cables which can be used to connect the DCW9931 cradle to a host computer. Also the pinout of the network cable is described. A1 The terminal does not respond immediately after the installation procedure. When the battery is completely empty, it takes some time for charging the battery to a certain activation voltage. Put the terminal in the cradle for charging.
USER’S MANUAL DWT 7133 3 C PRODUCT ORDERING INFORMATION Opticon Code Handheld wand terminal DWT 7133 red light optional: infra red light A73104R0010 A73104 I 0010 Communication and charging station DCW 9931 cradle 220 V AC optional: 110 V AC A73300N0010 A73300N0030 Connection cables for cradle RS 232 cable DB9 female (DB9-Mod.8P8) A73400N0030 RS 232 cable DB25 female (DB25-Mod.8P8) A73400N0040 RS 485 cable (Mod.8P8-Mod.
