User Manual
Table Of Contents
- 슬라이드 번호 1
- 슬라이드 번호 2
- 1. Precautions
- 1.7 Do not install device while driving - Please avoid any activities that may cause careless driving 1.8 Turn off the ignition before set up the device. 1.9 Do not install the device near any air bags in a car - It may cause severe damage if air bags explode. 1.10 Do not touch the device with wet hands - It may cause possible risk of an electric shock 1.11 Keep the installation location of inside and outside antenna clean - Please organize cable lines and antenna locations to avoid any possible interference while operating a vehicle. 1.12 Stop and Turn Off the device immediately if a smog comes out of the product or any strange odor is detected from the product - Do not attempt to fix the device. Please contact your store representative 1.13 Warning message for use of unauthorized antennas, cables, and/or coupling devices - It may not properly operate
- 슬라이드 번호 5
- 3.1.1 Summary The device may be installed on cars, trucks, trailers, boats and homes to improve user’s mobile phone signal. (Please see page 13 for Operating Frequency) 3.1.2 Features
- 슬라이드 번호 7
- 슬라이드 번호 8
- 슬라이드 번호 9
- 슬라이드 번호 10
- 슬라이드 번호 11
- 슬라이드 번호 12
- 슬라이드 번호 13
- 슬라이드 번호 14
- 슬라이드 번호 15
- 슬라이드 번호 16
- 슬라이드 번호 17
10
All rights reserved
AVHR-5000N
5. Trouble Shooting
5.1 LED Alarm
ITEM GREEN LED RED LED Problem Reference
Setting/Resetting
ON
(after 3 times blinks)
3 times blinks See 4.1.1
Normal Mode ON OFF See 4.1.2
Cellular
Overload Blink( once) - See 4.1.3
Oscillation Blink(twice) - See 4.1.4
Insufficient
Isolation
Blink(3 times) - See 4.1.5
Alarm Checking Blink(Consecutively) - See 4.1.6
Sleep Mode Blink(4 times) - See 4.1.7
PCS
Overload - Blink( once) See 4.1.3
Oscillation - Blink(twice) See 4.1.4
Insufficient
Isolation
- Blink(3 times) See 4.1.5
Alarm Checking - Blink(Consecutively) See 4.1.6
Sleep Mode - Blink(4 times) See 4.1.7
5.1.1 ① Check if the LED light is ON, on the cigarette power adapter
② Verify that DC cord is connected correctly
5.1.2 ② Green LED light is normal mode. If it blinks 2-4 times in a few
seconds, please see 4.1.3 ~ 4.1.7
5.1.3 ② This is normal mode that checking on input power signal and shows
signal status to users.
② It will go resume normal operation mode after Overload Detection.
5.1.4 ② There is an oscillation between inside and outside antenna.
② This status is caused by surrounding structural interferences that
can temporarily disturb mobile signals. The amplifier will auto detect
available signals as you drive to other locations.
The Green LED light will turn ON once normal mode resumes.
5.1.5 ② The isolation may occur between inside and outside antenna
② If LED light blinks three times during installation, move the inside and
outside antenna away from each other and RESTART the amplifier.
② If LED light blinks three times after the installation, it could be caused
by surrounding structure.
The device will auto adjust as vehicle moves.