- Content - All rights reserved AVHR-5000N 1. Precautions 2. System Components 2.1 Components 2.2 Installation 3. General Information 3.1 Features 4. Installation 4.1 External Antenna Installation 4.2 Inside Antenna Installation 4.3 Amplifier and Antenna Connection 4.4 Operating Instructions 5. Trouble Shooting 5.1 LED Alarm 5.2 Insufficient Outside Signal Problem 5.3 Vehicle Battery Discharge Problem 6. Safeguard features 6.1 Summary 6.2 Features 7. Specification 7.1 Amplifier Specification 7.
1. Precautions This is a CONSUMER device. This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer.
1.7 Do not install device while driving - Please avoid any activities that may cause careless driving 1.8 Turn off the ignition before set up the device. 1.9 Do not install the device near any air bags in a car - It may cause severe damage if air bags explode. 1.10 Do not touch the device with wet hands - It may cause possible risk of an electric shock 1.
2. System Components 2.1 Components (A) ① Inside Antenna ② Dual Band Amplifier ③ User Manual (A) ⑤ Outside Antenna ④ Cigarette power adapter Note: (A) Mark Purchase separately ① . Inside Antenna: connects signal between mobile phone and amplifier ②. Dual Band Amplifier: amplifies signal by receiving base station signals through Outdoor antenna to In-door Antenna ③. User Manual: shows how to operate system ④. Cigarette Power Adapter: Power Source ⑤.
3. General Information 3.1 Features 3.1.1 Summary The device may be installed on cars, trucks, trailers, boats and homes to improve user’s mobile phone signal. I. II. III. IV. Decrease dropped call Increase 2G/3G data speed Battery life extension Voice quality improvement (Please see page 13 for Operating Frequency) 3.1.2 Features I. All rights reserved AVHR-5000N Strong coverage area - Gain 48dB II. Automatic Overload Protection & Detection System - Plug and Operate Systems III. 23dBm(0.
4. Installation 4.1 External Antenna Installation 4.1.1 Outside antenna has magnetic feature to mount on the roof of vehicle 4.1.2 Outside antenna distance should be at least 5 feet from inside antenna 4.1.3 Recommended to mount outside antenna near rear end of the roof. Good Better Best 4.2 Inside Antenna Installation 4.2.1Inside antenna is mounted using the self-adhesive. It must be placed in a location that will be at least 0.5m (20 inches) from where cell phones will be located. 4.2.
4.3 Amplifier and Antenna Connection 4.3.1 Place the amplifier under the seat or appropriate location. 4.3.2 Connect inside and outside antenna connector to Amplifier. 4.4 Operating Instructions 4.4.1 Plug in cigarette power cord and press the button to turn ON as shown below. The red LED light should be ON indicating its operation.
4.4.2 Connect DC Jack as shown below 4.4.3 Turn ON the Switch as shown below 4.4.4 After turning ON the switch, green LED light will be on. Green LED indicates that system is in a normal mode. Green and Red LED will flash 3 times simultaneously. After the initial loading, the green LED light will be on during operation.
5. Trouble Shooting 5.1 LED Alarm ITEM GREEN LED RED LED Problem Reference 3 times blinks See 4.1.1 ON OFF See 4.1.2 Overload Blink( once) - See 4.1.3 Oscillation Blink(twice) - See 4.1.4 Insufficient Isolation Blink(3 times) - See 4.1.5 Alarm Checking Blink(Consecutively) - See 4.1.6 Sleep Mode Blink(4 times) - See 4.1.7 Overload - Blink( once) See 4.1.3 Oscillation - Blink(twice) See 4.1.4 Insufficient Isolation - Blink(3 times) See 4.1.
5.1.6 ① The Overload Protection System includes the following: AGC (Automatic Gain Level Control) AIC (Automatic Isolation Detection) ASC (Automatic Reset Control) ② During Alarm checking process, the Amplifier may not operate. 5.1.7 ① When LED is green or red with a flash four times at working, Sleep Mode is operated. Because reverse signal has not been existed for a certain time. ② If Reverse signal occur at the Sleep Mode, repeater is working normally and LED does not flash. 5.
6. Safeguard features 6.1 Summary This equipment have functions to protect as follows. I. II. III. IV. V. Isolation check mechanism Oscillation check mechanism Sleep Mode mechanism ALC(Auto Level Control) mechanism RF Shut Down mechanism 6.2 Feature 6.2.1 Isolation check mechanism - The booster automatically checks the isolation by increasing the DL path gain by 1dB when the power supply is switched on and/or the oscillation occurs.
7. Specification 7.1 Amplifier Specification Items Cellular PCS Remarks Downlink 869 ~ 894 MHz 1930 ~ 1990 MHz Uplink 824 ~ 849 MHz 1850 ~ 1910 MHz Downlink 48dB±2.0dB 48dB±2.0dB Uplink 48dB±2.0dB 48dB±2.
7.2 Outside Antenna Specification ● TQC-900/1800CII Items Frequency Range Remarks 890 ~ 960 MHz Operating Frequency 1710 ~ 1990 MHz Gain 5dBi - VSWR ≤ 2.0 : 1 - Impedance 50 Ω - Max Power-W 50W Polarization Vertical - Connector FME(Female) - Antenna Length 11.02 inch (28Cm) - Frequency Range Remarks ● TS210580 Items 700 ~ 800 MHz 824 ~ 894 MHz 880 ~ 960 MHz - Operating Frequency 1710 ~ 1880 MHz 1850 ~ 1990 MHz 2110 ~ 2170 MHz 5dBi - VSWR ≤ 2.
7.3 Inside Antenna Specification ● TQC-900/1800E Items Frequency Range Remarks 820 ~ 890 MHz Operating Frequency 1710 ~ 1990 MHz Gain 2dBi - VSWR < 2.1 : 1 - Impedance 50 Ω - Max Power-W 25W Polarization Vertical or Horizontal - Connector FME(Female) - Antenna Length 4.73 inch (12cm) - Frequency Range Remarks ● TS210380 Items 700 ~ 800 / 824~ 894 MHz Operating Frequency 880~960 / 1850 ~ 1990 MHz 3dBi - VSWR < 1.
7.4 Cigarette Power Code Specification 7.4.1 Input Specification Items Min Typical Max Normal DC Input Voltage 12V - 24V DC Input Voltage Range 12V - 24V DC Input Voltage Current - - 3.0A 7.4.2 Output Specification Items Min Typical Max Normal DC Output Voltage - 6.0Vdc - DC Output Voltage Range 5.7Vdc - 6.3Vdc Load Current Range - - 3.5A Ripple - - 350mV Over Current Protection 4.2 - 7.0A Short Circuit Protection - Yes - 8. Certificates 8.
Memo AVHR-5000N All rights reserved 17
