OPEL COMBO Owner's Manual
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 20 Seats, restraints ........................... 33 Storage ........................................ 54 Instruments and controls ............. 62 Lighting ........................................ 88 Climate control ............................. 95 Driving and operating ................. 101 Vehicle care ...............................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". We wish you many hours of pleasurable driving.
Introduction 5
6 In brief In brief Vehicle unlocking Unlocking with key Unlocking with radio remote control Initial drive information Turn the key in the driver's door lock towards the front of the vehicle. Press button Ä to unlock the vehicle. Press button Å to unlock the load compartment only. Open the doors by pulling the handles. To open the tailgate, press the button under the tailgate handle. Radio remote control 3 20, Central locking system 3 21, Load compartment 3 25, Power windows 3 29.
In brief Seat adjustment Seat backrests Seat height Turn handwheel. Do not lean on backrest when adjusting. Seat position 3 34, Seat adjustment 3 34. Lever pumping motion up = higher down = lower 7 Seat positioning Pull handle, slide seat, release handle. Seat position 3 34, Seat adjustment 3 34. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. Operate lever and adjust body weight on seat to raise or lower it.
8 In brief Head restraint adjustment Seat belt Mirror adjustment Interior mirror Press release catch, adjust height, engage. Head restraints 3 33. Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle. Seat position 3 34, Seat belts 3 39, Airbag system 3 42. Adjust the lever on the underside to reduce dazzle.
In brief Steering wheel adjustment Exterior mirrors Swivel lever in required direction. 9 Select the relevant exterior mirror by turning the control to left _ or right 6. Then swivel the control to adjust the mirror. In position o no mirror is selected. Convex exterior mirrors 3 28, Electric adjustment 3 28, Folding exterior mirrors 3 28, Heated exterior mirrors 3 29. Unlock the lever, adjust the steering wheel, then engage lever and ensure it is fully locked.
10 In brief Instrument panel overview
In brief 1 2 3 Fixed air vents ..................... 100 Side air vents ........................ 99 Light switch .......................... 88 4 Turn and lane-change signals, headlight flash, low beam and high beam ..... 90 Instruments .......................... 68 5 6 7 Driver Information Centre ...... 79 Windscreen wiper, windscreen washer system, rear window wiper/washer ........................ 63 Trip odometer reset ............... 68 Centre air vents ....................
12 In brief
In brief Exterior lighting Fog lights Turn light switch: § = off / daytime running lights 9 = sidelights / headlights Press light switch: > = front fog lights r = rear fog light Lighting 3 88, Daytime running lights 3 89. 13 Headlight flash, high beam and low beam headlight flash = pull lever high beam = push lever low beam = pull lever High beam 3 88, Headlight flash 3 88.
14 In brief Turn and lane-change signals Hazard warning flashers Horn lever up = right turn signal lever down = left turn signal Operated with the ¨ button. Hazard warning flashers 3 90. Press j. Turn and lane-change signals 3 90.
In brief Washer and wiper systems Windscreen wiper Twist lever: = off § Ç = intermittent wiping È = slow É = fast For a single wipe when the windscreen wiper is off, move the lever up. Windscreen wiper 3 63, Wiper blade replacement 3 131. 15 Windscreen and headlight washer systems Rear window wiper and washer systems Pull lever. Windscreen and headlight washer system 3 63, Washer fluid 3 129. Twist band to activate the rear window wiper.
16 In brief Climate control Heated rear window, heated exterior mirrors The heating is operated by pressing the Ü button. Heated rear window 3 32. Demisting and defrosting the windows Electronic climate control system Air conditioning system Set the temperature control to warmest level. Set fan speed to highest level. Set air distribution control to V. Cooling n on. Heated rear window Ü on. Press button Ê. Temperature and air distribution are set automatically and the fan runs at a high speed.
In brief Transmission Manual transmission automated Manual transmission Reverse: with the vehicle stationary, wait 3 seconds after depressing the clutch pedal, pull up the collar on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection. Manual transmission 3 107.
18 In brief Starting the engine ■ Turn key to position MAR ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake ■ manual transmission automated: operate brake, the transmission automatically shifts to N (neutral) ■ do not operate accelerator pedal ■ diesel engines: turn the key to position MAR for preheating and wait until control indicator ! goes out ■ turn key to position AVV and release Starting the engine 3 102.
In brief Parking ■ Always apply the parking brake. Activate the manual parking brake without pressing the release button. Apply as firmly as possible on a downhill slope or uphill slope. Depress foot brake at the same time to reduce operating force. ■ Switch off the engine. Turn the ignition key to position STOP and remove it. Turn the steering wheel until the steering wheel lock is felt to engage. ■ If the vehicle is on a level surface or uphill slope, engage first gear before switching off the ignition.
20 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 20 Doors ........................................... 23 Vehicle security ............................ 27 Exterior mirrors ............................ 28 Interior mirrors ............................. 29 Windows ...................................... 29 Keys, locks Keys Replacement keys The key number is specified in the Car Pass or on a detachable tag.
Keys, doors and windows Used to operate: ■ Central locking system 3 21 ■ Anti-theft locking system 3 27 ■ Power windows 3 29 The radio remote control has a range of up to 5 metres. It can be restricted by external influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation.
22 Keys, doors and windows A pull on an interior door handle unlocks and opens the respective door. For safety reasons, the vehicle cannot be locked if the key is in the ignition switch. Press button Ä: Front doors are unlocked. Note If engaged, the anti-theft security lock on the sliding side door remains engaged even after unlocking the vehicle with the remote control. Anti-theft security lock 3 23. Locking Unlocking Close all doors.
Keys, doors and windows Automatic locking The vehicle can be configured to automatically lock the doors when vehicle speed exceeds 20 km/h. Driver Information Centre 3 79. Unlocking the load compartment from inside the vehicle Child locks 9 Warning 23 Doors Sliding door Use the child locks whenever children are occupying the rear seats. Pull lever on interior handle and slide door. Caution Press button Å: The load compartment (rear doors / tailgate and sliding side doors) are unlocked.
24 Keys, doors and windows Caution To avoid damage, do not attempt to operate the sliding side door when the fuel filler flap is open. Refuelling 3 120. Anti-theft security lock Using a suitable tool, turn the lock switch on the sliding side door to locked position 1. The door cannot be opened from outside. The anti-theft security lock remains engaged even after unlocking the vehicle with the remote control. To disengage, turn the switch to unlocked position 2.
Keys, doors and windows The right hand rear door is released using the lever. 9 Warning The rear lights may be obscured if the rear doors are open and the vehicle is parked on the roadside. Make other road users aware of the vehicle, by using a warning triangle or other equipment specified in the road traffic regulations. The doors are retained in the 90º position by locking stays. To open the doors to 180º, push the latch and swing open to the desired position.
26 Keys, doors and windows smelled, could enter the vehicle. This can cause unconsciousness and even death. Closing Emergency tailgate opening from inside the vehicle Caution Before opening the tailgate check overhead obstructions, such as a garage door, to avoid damage to the tailgate. Always check the moving area above and behind the tailgate. Note The installation of certain heavy accessories onto the tailgate may affect its ability to remain open. Use the interior handle.
Keys, doors and windows Vehicle security Activating Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. The system deadlocks all the doors. All doors must be closed otherwise the system cannot be activated.
28 Keys, doors and windows Exterior mirrors Electric adjustment Folding Select the relevant exterior mirror by turning the control to left _ or right 6. Then swivel the control to adjust the mirror. In position o no mirror is selected. For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing.
Keys, doors and windows Heated mirrors Interior mirrors Windows Manual anti-dazzle Windscreen 29 Windscreen stickers Do not attach stickers such as toll road stickers or similar on the windscreen in the area of the interior mirror. Manual windows Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. The door windows can be opened or closed with the window winders.
30 Keys, doors and windows Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move. Switch on ignition to operate power windows. Pushing or pulling firmly and then releasing: window moves up or down fully with safety function enabled. To stop movement, operate the switch once more in the same direction. With the ignition key removed or in the STOP position, the windows can be operated for approx.
Keys, doors and windows Rear windows Child safety system for rear windows Press switch , to deactivate rear door power windows. To activate, press , again. Operating windows from outside The windows can be operated remotely from outside the vehicle when locking or unlocking the vehicle. Central locking system 3 21. 31 Opening rear windows Press and hold the Ä button to open windows. Press and hold the e button to close windows. Release button to stop window movement.
32 Keys, doors and windows Heated rear window Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Sun visors The sun visors can be folded down or swivelled to the side to prevent dazzling. If the sun visors have integral mirrors, the mirror covers should be closed when driving. A ticket holder is located on the backside of the sun visor.
Seats, restraints Seats, restraints Head restraints ............................ 33 Front seats ................................... 34 Rear seats ................................... 37 Seat belts ..................................... 39 Airbag system .............................. 42 Child restraints ............................. 48 Head restraints Adjustment Position Front head restraints, height adjustment 33 9 Warning Only drive with the head restraint set to the proper position.
34 Seats, restraints Rear head restraints, height adjustment Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. Pull the head restraint upwards or press the catch to release and push the head restraint downwards. Removal Rear head restraints, removal Press both catches, pull the head restraint upwards and remove. Secure the removed head restraint in the load compartment. Note Approved accessories may only be attached if the seat is not in use.
Seats, restraints 9 Danger Seat positioning Seat backrests Pull handle, slide seat, release handle. Turn handwheel. Do not lean on backrest when adjusting. Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. 9 Warning Never store any objects under the seats except in the underseat storage compartment 3 55.
36 Seats, restraints Seat height Armrest Heating Lever pumping motion up = higher down = lower Raise or lower the armrest as required. Activate seat heating by pressing button ß for the respective front seat with the ignition on. Activation is indicated by the LED in the button. Pressing button ß once more deactivates seat heating. Prolonged use for people with sensitive skin is not recommended. Operate lever and adjust body weight on seat to raise or lower it.
Seats, restraints Rear seats ■ Secure the folded seat in the upright position by attaching the flexible cord located on the seat frame, to the rear seat head restraint. 9 Warning Never adjust seats while driving as they could move uncontrollably. Unfolding the seats Folding the seats The load compartment area can be increased by folding up the rear seats. 9 Warning When folding the seat use caution - beware of moving parts. Ensure the seat is secure when completely folded.
38 Seats, restraints Installing the seats ■ Raise the backrest and replace the head restraint. ■ The backrest is properly engaged when the red mark on the release lever is no longer visible. 9 Warning ■ With the seat folded in the upright position, push the release lever and remove the seat assembly. ■ Store the head restraint on the rear of the seat frame. ■ Attach the seat assembly front supports on the anchor points. ■ Push the release lever to ensure the seat is securely latched.
Seats, restraints Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position. Therefore the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves. Seat belts are designed to be used by only one person at a time. Child restraint system 3 48.
40 Seats, restraints Three-point seat belt Height adjustment Fastening Withdraw the belt from the retractor, guide it untwisted across the body and insert the latch plate into the buckle. Tighten the lap belt regularly whilst driving by pulling the shoulder belt. Seat belt reminder X 3 73. Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body.
Seats, restraints Removing Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving. To release belt, press red button on belt buckle. Seat belts on the rear seats The seat belt for the rear centre seat can only be withdrawn from the retractor if the backrest is in the rear position.
42 Seats, restraints Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered, the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. Note Depending on the severity of a collision, the fuel system may also be cut-off and the engine switched off automatically, for safety reasons. Resetting the fuel cut-off system; refer to "Fuel system messages" 3 85.
Seats, restraints EN: NEVER use a rear-facing child restraint system on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur. DE: Nach hinten gerichtete Kindersitze NIEMALS auf einem Sitz verwenden, der durch einen davor befindlichen AKTIVEN AIRBAG geschützt ist, da dies den TOD oder SCHWERE VERLETZUNGEN DES KINDES zur Folge haben kann.
44 Seats, restraints mesmo, poderá ocorrer a PERDA DE VIDA ou FERIMENTOS GRAVES na CRIANÇA. IT: Non usare mai un sistema di sicurezza per bambini rivolto all'indietro su un sedile protetto da AIRBAG ATTIVO di fronte ad esso: pericolo di MORTE o LESIONI GRAVI per il BAMBINO! EL: ΠΟΤΕ μη χρησιμοποιείτε παιδικό κάθισμα ασφαλείας με φορά προς τα πίσω σε κάθισμα που προστατεύεται από μετωπικό ΕΝΕΡΓΟ ΑΕΡΟΣΑΚΟ, διότι το παιδί μπορεί να υποστεί ΘΑΝΑΣΙΜΟ ή ΣΟΒΑΡΟ ΤΡΑΥΜΑΤΙΣΜΟ.
Seats, restraints acest lucru poate duce la DECESUL sau VĂTĂMAREA GRAVĂ a COPILULUI. CS: NIKDY nepoužívejte dětský zádržný systém instalovaný proti směru jízdy na sedadle, které je chráněno před sedadlem AKTIVNÍM AIRBAGEM. Mohlo by dojít k VÁŽNÉMU PORANĚNÍ nebo ÚMRTÍ DÍTĚTE. SK: NIKDY nepoužívajte detskú sedačku otočenú vzad na sedadle chránenom AKTÍVNYM AIRBAGOM, pretože môže dôjsť k SMRTI alebo VÁŽNYM ZRANENIAM DIEŤAŤA.
46 Seats, restraints Keep the area in which the airbag inflates clear of obstructions. Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The front airbag system is triggered in the event of a front-end impact of a certain severity. The ignition must be switched on. The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and head of the front seat occupants considerably.
Seats, restraints Deactivate the front passenger airbag system as follows: 1. Press the SETq button once to access the settings menu. 2. Press SETq again (repeatedly) to cycle through the menu functions until menu option Pass bag (in Standard version) - or Passenger bag (in Multifunction version) is displayed. 3. Press the R or S button to switch from Pass bag On to Pass bag off (Standard version) - or from Passenger bag On to Passenger bag Off (Multifunction version) 4.
48 Seats, restraints Reactivating front passenger airbag system - see Driver Information Centre 3 79. Child restraints Child restraint systems We recommend the Opel child restraint system which is tailored specifically to the vehicle. When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system. Always comply with local or national regulations.
Seats, restraints Allow children to enter and exit the vehicle only on the side facing away from the traffic. When the child restraint system is not in use, secure the seat with a seat belt or remove it from the vehicle. Note Do not stick anything on the child restraint systems and do not cover them with any other materials. A child restraint system which has been subjected to stress in an accident must be replaced.
50 Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system Front passenger seat Second row Third row Weight and age class activated airbag deactivated airbag outboard seat centre seat Group 0: up to 10 kg or approx. 10 months X U1 U, < U X Group 0+: up to 13 kg or approx. 2 years X U1 U, < U X Group I: 9 to 18 kg or approx. 8 months to 4 years X U1 U, < U X Group II: 15 to 25 kg or approx.
Seats, restraints 51 Permissible options for fitting an ISOFIX child restraint system On front passenger seat On outboard seats On centre seat in On the seats in in the second row the second row the third row Weight class Size class Fixture Group 0: up to 10 kg E ISO/R1 X IL X X Group 0+: up to 13 kg E ISO/R1 X IL X X D ISO/R2 X IL X X C ISO/R3 X IL1) X X D ISO/R2 X IL X X C ISO/R3 X IL1) X X B ISO/F2 X IUF X X B1 ISO/F2X X IUF X X A ISO/F3 IUF X X Group
52 Seats, restraints ISOFIX size class and seat device A – ISO/F3 B – ISO/F2 B1 – ISO/F2X C – ISO/R3 D – ISO/R2 E – ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. ISOFIX mounting brackets are indicated by a label on the backrest. Before fastening a child seat adjust the head restraint to use position 3 33. Top-tether fastening eyes In addition to the ISOFIX mounting, fasten the Top-Tether strap to the Top-Tether fastening eyes.
54 Storage Storage Storage compartments ................ 54 Load compartment ....................... 56 Roof rack system ......................... 59 Loading information ..................... 60 Storage compartments 9 Warning Storage compartments are located in the instrument panel. Document holder Do not store heavy or sharp objects in the storage compartments.
Storage 55 Glovebox Overhead console Underseat storage Pull lever to open the glovebox cover. Depending on version, the glovebox may be lockable. The glovebox should be closed whilst driving. Store only lightweight items such as paperwork or maps in the overhead console. Pull the loop on the seat cushion to gain access to the storage area. Cupholders Cupholders are located in the console between the front seats. The cupholders can also be used to hold the portable ashtray unit 3 68.
56 Storage Load compartment To fold up, lower seats to the floor until they engage audibly. Raise backrests and guide them into an upright position until they engage audibly. The backrests are properly engaged when both red marks on the release levers are no longer visible. Ensure that the seat belts are positioned correctly before returning the seats to the upright position. Folding down rear seat backrests The rear seat backrest is divided into two parts. Both parts can be folded down.
Storage 57 Closing Opening Removing Pull the cover towards the rear using the handle and engage it in the retainers at the sides. Remove load compartment cover from the retainers at the sides. Hold the cover and guide it until it is fully rolled up. Open the load compartment cover. Pull the release lever and lift cover from retainers. Installing Insert either side of the load compartment cover in the recess, pull the release lever. Insert the load compartment cover and engage.
58 Storage Rear parcel shelf or the lower position. In the lower position, the maximum load permissible is 70 kg. The rear parcel shelf consists of two parts - a front part and rear part. The front part can be opened or closed, allowing for greater flexibility in the load compartment. Do not place any excessively heavy or sharp-edged objects on the rear parcel shelf.
Storage To remove, lift the front part of the parcel shelf by releasing it from the front retainers (1) on both sides. Lift the rear part of the parcel shelf by releasing it from the rear retainers (2 and 3) on both sides. Installing Refit the parcel shelf by engaging in front and rear retainers on both sides. Lashing eyes Van The lashing eyes are designed to secure items against slippage, e.g. using lashing straps or a luggage net.
60 Storage To fasten a roof rack, insert the mounting bolts in the holes indicated in the illustration. Loading information ■ Heavy objects in the load compartment should be evenly distributed and placed as far forward as possible. If objects can be stacked, the heavier objects should be placed at the bottom. ■ Secure objects with lashing straps attached to lashing eyes 3 59. ■ Secure loose objects in load compartment to prevent them from sliding.
Storage luggage (7 kg) and all fluids (tank 90 % full). Optional equipment and accessories increase the kerb weight. ■ Driving with a roof load increases the sensitivity of the vehicle to cross-winds and has a detrimental effect on vehicle handling due to the vehicle's higher centre of gravity. Distribute the load evenly and secure it properly with retaining straps. Adjust the tyre pressure and vehicle speed according to the load conditions. Check and retighten the straps frequently.
62 Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 62 Warning lights, gauges and indi‐ cators ........................................... 68 Information displays ..................... 79 Vehicle messages ........................ 85 Trip computer ............................... 86 Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked.
Instruments and controls Horn Windscreen wiper/washer Windscreen wiper 63 Adjustable wiper interval Wiper lever in position Ç. The windscreen wiper will automatically adapt to the speed of the vehicle. Windscreen washer Press j. Twist lever: = off § Ç = intermittent wiping È = slow É = fast For a single wipe when the windscreen wiper is off, move the lever up. Do not use if the windscreen is frozen. Switch off in car washes.
64 Instruments and controls Rear window wiper/washer Outside temperature Clock Depending on model variant, the current time and/or date may appear in the Driver Information Centre 3 79. Values can be adjusted via the SETq, R and S buttons on the instrument panel. Twist to activate the rear window wiper. Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times. Do not use if the rear window is frozen. Switch off in car washes.
Instruments and controls Set time in Driver Information Centre - Standard version 5. Press SETq to confirm changes; the minutes will flash in the display. 6. Press R or S to increase or decrease the displayed value. 7. Press SETq briefly to confirm changes and automatically return to the previous display screen. Set time and date in Driver Information Centre Multifunction version 1. Press the SETq button once to access the settings menu. 2.
66 Instruments and controls 4. Press R or S to increase or decrease the displayed value. 5. Press SETq briefly to confirm changes and automatically return to the previous display screen. To change the clock mode between 12 hour and 24 hour clock: 1. Press R or S to select Mode and press SETq to access this submenu option; the display will flash. 2. Press R or S to change clock mode between 12h and 24h. 3. Press SETq briefly to confirm changes and automatically return to the previous display screen.
Instruments and controls Short wheelbase van Combo Tour 67 Do not damage the power outlets by using unsuitable plugs. If the tyre repair kit is in operation, switch off all electrical consumers. Tyre repair kit 3 145. Cigarette lighter Long wheelbase van Do not exceed the maximum power consumption of 180 watts. With ignition off, the power outlets are deactivated. Additionally the power outlets are deactivated in the event of low battery voltage.
68 Instruments and controls Ashtrays Caution To be used only for ash and not for combustible rubbish. Warning lights, gauges and indicators Odometer Instrument cluster The needles of the instruments briefly rotate to the end position when the ignition is switched on. Speedometer Displays the recorded distance in km. H may appear in the display until the vehicle has travelled 100 km. Trip odometer The portable ashtray should be placed in the cupholders in the centre console. Indicates vehicle speed.
Instruments and controls To reset the trip odometer, press and hold the TRIP button for a few seconds while the relevant trip odometer is displayed. Tachometer Caution If the needle is in the red warning zone, the maximum permitted engine speed is exceeded. Engine at risk. Fuel gauge Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Displays the fuel level or gas level in the tank depending on the operation mode.
70 Instruments and controls CNG fuel gauge Fuel selector Fuel for natural gas operation 3 119, Refuelling 3 120. Engine coolant temperature gauge In natural gas operation mode, the four vertical bars next to CNG correspond to the methane level in the cylinders. As the fuel level diminishes, the bars in the CNG fuel gauge disappear. CNG and the one remaining bar will flash if the methane level in the cylinders is low. Refuelling 3 120.
Instruments and controls If control indicator $ illuminates in conjunction with a message in the Driver Information Centre 3 79 the coolant temperature is too high. Seek the assistance of a workshop. Caution If engine coolant temperature is too high, stop vehicle, switch off engine. Danger to engine. Check coolant level. Service display Service display is available in vehicles with Multifunction version of the Driver Information Centre 3 79.
72 Instruments and controls Control indicators in the instrument cluster
Instruments and controls Generic warning 9 illuminates yellow. Depending on model variant, control indicator 9 may illuminate independently or in conjunction with Æ, t, Z or r. If 9 illuminates together with I; stop engine immediately and seek the assistance of a workshop. Simultaneously a warning message may be displayed in the Driver Information Centre 3 79. 9 also illuminates if the fuel cut-off switch is triggered, or if a fault is detected in the engine oil pressure sensor. Consult a workshop.
74 Instruments and controls system. Seek the assistance of a workshop. The airbags and belt pretensioners may fail to trigger in the event of an accident. Deployment of the belt pretensioners or airbags is indicated by continuous illumination of v. 9 Warning Have the cause of the fault remedied immediately by a workshop. Belt pretensioners, airbag system 3 39, 3 42. Airbag deactivation * illuminates yellow.
Instruments and controls 9 Warning Stop. Do not continue your journey. Consult a workshop. Illuminates if the brake vacuum servo fails; the brake pedal becomes stiff when pressed. The brake system remains operational however, assistance will be reduced. The steering may also require considerably more effort when turning. Illuminates after the ignition is switched on if the parking brake is applied 3 112. Brake pad wear F illuminates yellow.
76 Instruments and controls Illuminates Interference due to external sources of ultrasound. Once the source of interference is removed, the system will operate normally. Have the cause of the fault in the system remedied by a workshop. Depending on version, 9 will illuminate as an alternative if control indicator r is not present. A warning message may also be displayed in the Driver Information Centre 3 79. A fault in the system is present. Continued driving is possible.
Instruments and controls Continue driving until [ extinguishes. If possible, do not allow engine speed to drop below 2000 rpm. Illuminates The diesel particle filter is full. Start cleaning process as soon as possible. Diesel particle filter 3 106, Stop-start system 3 103. Engine oil pressure I illuminates red. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. Illuminates when the engine is running Caution Engine lubrication may be interrupted.
78 Instruments and controls The warning will be repeated every time the engine is started, until the engine oil is changed and the service display is reset. Seek the assistance of a workshop. Service display 3 71. Low engine oil level Illuminates Level in fuel tank is too low. Refuel immediately 3 120. Never run the tank dry. Catalytic converter 3 107. Flashes Fault in fuel system. Have the cause of the fault remedied by a workshop. Fuel gauge 3 69. y illuminates red.
Instruments and controls One or more of the exterior lights is faulty 3 132. Depending on version, 9 will illuminate as an alternative if control indicator µ is not present. A warning message may also be displayed in the Driver Information Centre 3 79. Generic warning 9 3 73. The system is on. Cruise control 3 115. Door open Information displays Driver Information Centre \ illuminates red. A door or the tailgate is open. High beam C illuminates blue.
80 Instruments and controls ■ ■ ■ ■ Transmission display 3 108 Stop-start system indicator 3 103 Vehicle messages 3 85 Trip computer 3 86 Selecting menus and options The menus and options can be selected via the buttons on the instrument panel. and a Multifunction version with further adjustable settings. Some of the displayed functions differ when the vehicle is being driven or at a standstill. Some options are only available when the vehicle is being driven.
Instruments and controls Settings menu options Standard version Press the R button to scroll up the screen and the menu options or to increase the displayed value. Press and hold to increase value rapidly (press again to stop on the required value). Press the S button to scroll down the screen and the menu options or to decrease the displayed value. Press and hold to decrease value rapidly (press again to stop on the required value).
82 Instruments and controls BAG P (Passenger front and side airbags activation/deactivation) Activate the front passenger airbags if an adult is occupying the front passenger seat. Deactivate airbags when a child restraint system is installed on this seat. 9 Danger Risk of fatal injury for a child using a child restraint system on a seat with activated front passenger airbag. Risk of fatal injury for an adult person on a seat with deactivated front passenger airbag.
Instruments and controls Press the SETq button when activated (On) to access the current set speed. Adjust as required and confirm. Warning chimes 3 85. TRIP B DATA Activate or deactivate the second trip computer (set to On or Off). Trip B records average consumption, distance travelled, average speed and travel time (driving time). The measurement can be restarted at any time. Trip computer 3 86.
84 Instruments and controls BUTTON VOLUME A chime is sounded every time the SETq, R or S button is pressed. Adjust the volume of these chimes and confirm. 8 volume levels are available. Warning chimes 3 85. SEAT BELT BUZZER (Reactivate warning chime for driver and/or front passenger seat belt reminder) This menu option is available only when the seat belt reminder has already been deactivated by a workshop.
Instruments and controls Vehicle messages Warning chimes Only one warning chime will sound at a time. The warning chime regarding unfastened seat belts has priority over any other warning chime. When starting the engine or whilst driving ■ If seat belt is not fastened. ■ If a certain speed is exceeded with the parking brake applied. ■ If the parking assist detects an object. ■ If a fault is detected in the parking assist. ■ If a door or the tailgate is not fully closed when starting-off.
86 Instruments and controls Trip computer The trip computer provides information on driving data, which is continually recorded and evaluated electronically.
Instruments and controls The trip computer will reset automatically when the maximum value of any of the parameters is exceeded. Average consumption Average consumption is displayed, taking into consideration the distance travelled and the fuel used since the last reset. The measurement can be restarted at any time. Instantaneous consumption Display of the instantaneous fuel consumption. _ _ _ _ will appear in the display if the vehicle is left parked with the engine running for a long time.
88 Lighting Lighting Exterior lighting High beam Light switch Exterior lighting ............................ 88 Interior lighting ............................. 91 Lighting features .......................... 94 Turn light switch: § = off / daytime running lights 9 = sidelights / headlights Control indicator 8 3 78. Tail lights Tail lights are illuminated together with headlights and sidelights. To switch from low to high beam, push lever. To switch to low beam, pull lever.
Lighting Headlight range adjustment Manual headlight range adjustment To adapt headlight range to the vehicle load to prevent dazzling of other road users: Press À or Á buttons until the required setting is displayed in the Driver Information Centre 3 79.
90 Lighting Hazard warning flashers Turn and lane-change signals Switch the indicator off manually by moving the lever to its original position. Front fog lights Operated with the ¨ button. Lever up = right turn signal Lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated. For five flashes, e.g.
Lighting Rear fog lights Misted light covers The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing. The mist disappears quickly by itself; to help, switch on the headlights. Operated by pressing the r button. The rear fog light can only be switched on when both the ignition and headlights or sidelights (with front fog lights) are on.
92 Lighting 3. Press the R or S button to increase or decrease the displayed value. 4. Press SETq briefly to confirm changes and automatically return to the previous display screen. Multifunction version of Driver Information Centre 1. Press the SETq button to access the settings menu. 2. Scroll through the menu options using the R or S buttons until menu option LIGHTING appears in the display. 3. Press the R or S button to increase or decrease the displayed value. 4.
Lighting Rear courtesy lights Removable rear courtesy light Centre switch position: automatic interior light. To operate manually when the doors are closed, press the lens on either side. Depending on model variant, the removable rear courtesy light may illuminate when the rear doors / tailgate or sliding side doors are opened and the central switch is in the middle position. Switch the light on permanently by pressing the top part of the central switch c.
94 Lighting Lighting features Battery discharge protection To ensure reliable engine restarts, several battery discharge protection features are implemented as part of the stop-start system. Stop-start system 3 103.
Climate control Climate control Climate control systems ............... 95 Air vents ....................................... 99 Maintenance .............................. 100 Climate control systems Heating and ventilation system 95 Heating will not be fully effective until the engine has reached normal operating temperature. Fan speed Adjust the air flow by switching the fan to the desired speed.
96 Climate control ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J. Air conditioning system Cooling n Press button n to switch on cooling. Activation is indicated by the LED in the button. Cooling is only functional when the engine is running and climate control fan is switched on. Press button n again to switch off cooling.
Climate control ■ Set fan speed to highest level. ■ Open all air vents. Electronic climate control system Demisting and defrosting the windows ■ Set temperature control to warmest level. ■ Set fan speed to highest level. ■ Set air distribution control to V. ■ Switch cooling n on. ■ Switch on heated rear window Ü. ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J.
98 Climate control clockwise = warm anticlockwise = cold Heating will not be fully effective until the engine has reached normal operating temperature. When the minimum temperature is set below 16 ℃, the electronic climate control system runs at maximum cooling. LO appears in the display. If the maximum temperature is set above 32 ℃, the electronic climate control system runs at maximum heating. HI appears in the display. Fan speed The selected fan speed is indicated with bars in the display.
Climate control of the passenger compartment air deteriorates, which may cause the vehicle occupants to feel drowsy. In warm and very humid ambient air conditions, the windscreen may mist up from outside, when cold air is directed towards it. If windscreen mists up from outside, activate windscreen wiper and deactivate V. Air vents Adjustable air vents At least one air vent must be open while cooling is on in order to prevent the evaporator from icing up due to lack of air movement.
100 Climate control Fixed air vents Additional air vents are located beneath the windscreen and door windows and in the foot wells. Maintenance Air intake Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low.
Driving and operating Driving and operating Driving hints ............................... 101 Starting and operating ............... 101 Engine exhaust .......................... 106 Manual transmission .................. 107 Manual transmission automa‐ ted .............................................. 108 Brakes ........................................ 112 Ride control systems ................. 113 Cruise control ............................. 115 Object detection systems ........... 116 Fuel ............
102 Driving and operating Ignition switch positions Starting the engine Before restarting or to switch off the engine, turn the key back to position STOP. Autostop During an Autostop, the engine is restarted automatically by depressing the clutch pedal. Vehicles with manual transmission automated (MTA): shift to a forward gear, release brake pedal or move lever to +, – or R to enable an automatic restart. Stop-start system 3 103.
Driving and operating Turbo engine warm-up Upon start-up, engine available torque may be limited for a short time, especially when the engine temperature is cold. The limitation is to allow the lubrication system to fully protect the engine. Vehicle shutdown Fuel cut-off system In the event of a collision of a certain severity, the fuel system is cut-off and the engine is switched off automatically, for safety reasons. A corresponding warning message may also appear in the Driver Information Centre 3 79.
104 Driving and operating Activation The stop-start system is available as soon as the engine is started, the vehicle starts-off and the conditions as stated below in this section are fulfilled. Deactivation Deactivate the stop-start system manually by pressing the ^ button in the centre console. LED in the button illuminates to confirm deactivation.
Driving and operating ■ the ambient temperature is not too low ■ the climate control system allows an Autostop ■ the self-cleaning function of the diesel particle filter is not active ■ the vehicle has moved since the last Autostop ■ the brake vacuum is sufficient ■ the windscreen wipers are not operating at fast speed ■ reverse gear is not selected ■ heated rear window is not operating Ambient temperature near to the freezing point can inhibit an Autostop.
106 Driving and operating Note In the event of an accident with airbag deployment, the engine is turned off automatically if the vehicle comes to a standstill within a certain time. Engine exhaust 9 Danger Engine exhaust gases contain poisonous carbon monoxide, which is colourless and odourless and could be fatal if inhaled. If exhaust gases enter the interior of the vehicle, open the windows. Have the cause of the fault rectified by a workshop.
Driving and operating Caution If the cleaning process is interrupted, there is a risk of provoking severe engine damage. Cleaning takes place quickest at high engine speeds and loads. Control indicator [ extinguishes as soon as the self-cleaning operation is complete. Catalytic converter The catalytic converter reduces the amount of harmful substances in the exhaust gases. Caution Fuel grades other than those listed on pages 3 118, 3 164 could damage the catalytic converter or electronic components.
108 Driving and operating Caution It is not advisable to drive with the hand resting on the selector lever. When gearshifting is recommended to improve fuel economy, control indicator [ or Ò illuminates in the Driver Information Centre 3 75. Manual transmission automated The manual transmission automated (MTA) permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control.
Driving and operating Selector lever R + - = Reverse gear. Engage only when vehicle is stationary. The transmission display shows "R" when reverse gear is engaged. = Shift to a higher gear. = Shift to a lower gear. Starting-off Always move the selector lever in the appropriate direction as far as it will go. After selecting A/M, + or - and releasing the selector lever, the lever automatically returns to the centre position. N = Neutral. = Drive position.
110 Driving and operating When the vehicle is parked and the driver's door is opened, a warning chime will sound if neutral is not selected or the foot brake has not been depressed. Engine braking Automatic mode When driving downhill, the manual transmission automated does not shift into higher gears until a fairly high engine speed has been reached. It shifts down in good time when braking. Manual mode To utilise the engine braking effect, select a lower gear in good time when driving downhill.
Driving and operating Electronic driving programmes Eco mode E When automatic mode is engaged, the Eco mode can be selected to reduce fuel consumption. Eco mode selects the most suitable gear depending on the speed of the vehicle, the engine speed and the intensity with which the accelerator is pressed. 111 Activation Press the E button on the selector lever housing. Control indicator E is shown in the transmission display to indicate activation.
112 Driving and operating Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when the brake pedal is depressed firmly. Considerably more force is needed for this. The braking distance is extended. Seek the assistance of a workshop before continuing your journey.
Driving and operating To release the parking brake, pull the lever up slightly, press the release button and fully lower the lever. To reduce the operating forces of the parking brake, depress the foot brake at the same time. A warning chime will sound if a certain speed is exceeded with the parking brake applied. Note The volume of the warning chime can also be adjusted via the Driver Information Centre 3 79. Control indicator R 3 74.
114 Driving and operating 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Adapt speed to the road conditions. Deactivation ASR is reactivated by pressing the ASR OFF button again. ASR is also reactivated the next time the ignition is switched on. Fault ASR will switch off automatically in the event of a fault. Control indicator x will illuminate in the instrument cluster in conjunction with a message in the Driver Information Centre 3 79.
Driving and operating Have the cause of the fault remedied by a workshop. Control indicator x 3 76. Cruise control The cruise control can store and maintain speeds above approx. 30 km/h. Deviations from the stored speeds may occur when driving uphill or downhill. 115 Switching on Turn end of lever to the ON position; control indicator m illuminates in the instrument cluster in conjunction with a message in the Driver Information Centre.
116 Driving and operating Alternatively accelerate to the desired speed and store by pushing lever upwards (+). Reduce speed With cruise control active, push lever downwards (-) or briefly push lever downwards (-) repeatedly; speed decreases continuously or in small increments. Switching off Turn end of lever to the OFF position; control indicator m extinguishes. The stored speed is deleted. Switching off the ignition also deletes the stored speed.
Driving and operating System operation The parking assist is turned on automatically when reverse gear is engaged. The intervals between the beeps become shorter as the vehicle gets closer to the obstacle. When the distance is less than 30 cm, the beeping is a continuous tone which stops immediately when the distance is increased. Fault In the event of a fault in the system, r illuminates and a message is displayed in the Driver Information Centre 3 79.
118 Driving and operating Caution Performance of the sensor can be reduced when sensors are covered, e.g. by ice or snow. Performance of the parking assist systems can be reduced due to heavy loading. Special conditions apply if there are taller vehicles involved (e.g. off-road vehicles, mini vans, vans). Object identification in the upper part of these vehicles cannot be guaranteed.
Driving and operating Caution Caution Use of fuel that does not comply to EN 228 or E DIN 51626-1 or equivalent can lead to deposits or engine damage and may affect your warranty. Use of fuel that does not comply to EN 590 or similar can lead to engine powerloss, increased wear or engine damage and may affect your warranty. Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage. Fuel for diesel engines Only use diesel fuel that complies with EN 590.
120 Driving and operating A slight loss of power and torque can be expected in petrol operation. You must therefore adapt your driving style (e.g. during overtaking manoeuvres) and vehicle loads (e.g. towing loads) accordingly. Every six months run the petrol tank down until control indicator § illuminates and then refuel. This is necessary to maintain fuel quality as well as system function necessary for petrol operation. Fill the tank completely at regular intervals to prevent corrosion in the tank.
Driving and operating To refuel, fully insert the pump nozzle and switch it on. After the automatic cut-off, the fuel tank can be topped up with a maximum of two doses of fuel. Natural gas refuelling Caution Wipe off any overflowing fuel immediately. To close, replace fuel filler cap and turn clockwise. Insert key into fuel filler cap and turn clockwise to lock, then remove key. Close the fuel filler flap.
122 Driving and operating German Erdgas English CNG = Compressed Natural Gas French GNV = Gaz Naturel (pour) Véhicules - or CGN = carburantgaz naturel Italian Metano (per auto) Fuel filler cap Only use genuine fuel filler caps. Diesel-engined vehicles have special fuel filler caps. Fuel cut-off system In the event of a collision of a certain severity, the fuel system is cut-off and the engine is switched off automatically, for safety reasons.
Driving and operating Towing General information Only use towing equipment that has been approved for your vehicle. Vehicles with natural gas engine may require special towing equipment. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment. Fitting of towing equipment could cover the opening of the towing eye. If this is the case use the coupling ball bar for towing.
124 Driving and operating The maximum permissible vertical coupling load (75 kg) is specified on the towing equipment identification plate and in the vehicle documents. Always aim for the maximum load, especially in the case of heavy trailers. The vertical coupling load should never fall below 25 kg. Rear axle load The permissible axle loads (see identification plate or vehicle documents) must not be exceeded.
Vehicle care Vehicle care General Information ................... 125 Vehicle checks ........................... 126 Bulb replacement ....................... 132 Electrical system ........................ 138 Vehicle tools .............................. 142 Wheels and tyres ....................... 142 Jump starting ............................. 152 Towing ....................................... 153 Appearance care .......................
126 Vehicle care ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft locking system. Putting back into operation When the vehicle is to be put back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir.
Vehicle care 127 If the bonnet is opened during an Autostop, the engine will be restarted automatically for safety reasons. Stop-start system 3 103. 9 Danger The ignition system uses extremely high voltage. Do not touch. Closing Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. Bonnet Opening Engine oil Push the safety catch and open the bonnet. Pull the release lever and return it to its original position. Secure the bonnet support.
128 Vehicle care We recommend the use of the same grade of engine oil that was used at last change. The engine oil level must not exceed the MAX mark on the dipstick. Caution Coolant level Caution Too low a coolant level can cause engine damage. Overfilled engine oil must be drained or suctioned out. When the engine oil level has dropped to the MIN mark, top up engine oil. Capacities 3 173. Fit the cap on straight and tighten it. Engine coolant The coolant provides freeze protection down to approx.
Vehicle care 9 Warning 129 Power steering fluid Washer fluid If the fluid level in the reservoir falls below the MIN mark consult a workshop. Fill with clean water mixed with a suitable quantity of windscreen washer fluid which contains antifreeze. Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. To top up use a 1:1 mixture of released coolant concentrate mixed with clean tap water. If no coolant concentrate is available, use clean tap water.
130 Vehicle care Brakes Battery A squealing noise, or illumination of brake pad wear control indicator F indicates that the brake lining is at its minimum thickness. Continued driving is possible but have the brake linings replaced as soon as possible. Once new brake linings are installed, do not brake unnecessarily hard for the first few journeys. Brake pad wear indicator F 3 75. The vehicle battery is maintenancefree provided that the driving profile allows sufficient charging of the battery.
Vehicle care Replacing the battery Note Any deviation from the instructions given in this paragraph may lead to a temporary deactivation of the stopstart system. 131 Wiper blade replacement Wiper blade on rear swing door Lift the wiper arm until it stays in the raised position, press button to disengage the wiper blade and remove. Attach the wiper blade slightly angled to the wiper arm and push until it engages. Lower wiper arm carefully.
132 Vehicle care Wiper blade on tailgate Bulb replacement Halogen headlights Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Replace headlight bulbs from within the engine compartment. Lift wiper arm, press retaining clips to detach wiper blade. Attach the wiper blade to the wiper arm and push until it engages. Lower wiper arm carefully.
Vehicle care 4. Insert new bulb in reflector so that the locating tab of the bulb aligns with the reflector recess. 5. Attach connector to bulb. 6. Engage wire clip. 7. Install protective cover. High beam 1. Remove protective cover. 2. Detach connector from bulb. 3. Disengage wire clip and remove bulb from reflector. 4. Insert new bulb in reflector so that the bulb aligns with the reflector recess. 5. Engage wire clip and attach connector onto bulb. 6. Install protective cover. Sidelight 1.
134 Vehicle care Tail lights 2. Withdraw bulb holder from reflector by turning anticlockwise. 3. Remove bulb from socket, insert new bulb. 4. Insert bulb holder in reflector. 5. Rotate clockwise to engage. 6. Install protective cover. Front turn signal light 1. Remove protective cover. 2. Withdraw bulb holder from reflector by turning anticlockwise. 3. Push bulb into holder slightly, rotate anticlockwise, remove and renew bulb. 4. Insert bulb holder in reflector. 5. Rotate clockwise to engage. 6.
Vehicle care 135 9. Engage connector plug. 10. Insert light housing in body, ensuring correct positioning. Tighten the three retaining screws. Side turn signal lights Have bulbs replaced by a workshop. 4. Unscrew the four retaining screws using a screwdriver. Turn bulb holder for reverse light anticlockwise and replace bulb. 5. Remove bulb holder and seal from light housing. 6. Push bulb into socket slightly, rotate anticlockwise, remove and renew bulb.
136 Vehicle care Number plate light Back doors Tailgate 1. Insert screwdriver as indicated by the arrows, press to the side and release the bulb housing. 2. Turn the bulb holder anticlockwise to remove from the bulb housing. Remove the bulb by pulling. 3. Replace the bulb. 4. Insert bulb holder in bulb housing and rotate clockwise 5. Install the bulb housing ensuring it engages correctly. 1. Insert screwdriver as indicated by the arrows, press to the left and release the bulb housing. 2.
Vehicle care Interior lights Front and rear courtesy light 1. Remove lens using a flat blade screwdriver. 2. Open the rear cover. 3. Renew bulb. 4. Close rear cover. 5. Reinstall lens. Front courtesy light, reading lights 1. Remove lens using a flat blade screwdriver. 2. Open the rear cover. 3. Renew bulbs. 4. Close rear cover. 5. Reinstall lens. 137 Removable rear courtesy light 1. Press the button at the top of the lamp assembly to release it.
138 Vehicle care 2. Prise the lamp assembly out at the points illustrated. 3. Renew bulb, ensuring it engages correctly. 4. Reinstall lamp assembly. Instrument panel illumination Have bulbs replaced by a workshop. Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse.
Vehicle care 139 Engine compartment fuse box Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. The fuse box is on the right of the engine compartment, next to the battery. To remove the protective cover and access the fuses, remove the two screws (see illustration).
140 Vehicle care No. Circuit Instrument panel fuse box F09 Rear door switch F10 Horn F14 High beam F15 PTCI heater F19 Air conditioning system F20 Heated rear window F21 Fuel pump F30 Fog lights F84 CNG system F85 Power outlets F86 Cigarette lighter, heated seats F87 Stop-start system F88 Mirror heating After having changed defective fuses refit the fuse box cover. If the fuse box cover is not closed correctly, malfunction may occur.
Vehicle care 141 No. Circuit No.
142 Vehicle care Vehicle tools Combi, Combo Tour Tools Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage. Seek the assistance of a workshop in the event of damage or unusual wear. Van The tools and the vehicle jacking equipment are in the storage area behind the front seat.
Vehicle care Tyre designations E.g. 215/60 R 16 95 H 215 = Tyre width, mm 60 = Cross-section ratio (tyre height to tyre width), % R = Belt type: Radial RF = Type: RunFlat C = Cargo or commercial use 16 = Wheel diameter, inches 95 = Load index e.g.
144 Vehicle care Tyres age, even if they are not used. We recommend tyre replacement every 6 years. Changing tyre and wheel size If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogramme the speedometer as well as the nominal tyre pressure and make other vehicle modifications. After converting to a different tyre size, have the label with tyre pressures replaced.
Vehicle care 145 Tyre repair kit Minor damage to the tyre tread can be repaired with the tyre repair kit. Do not remove foreign bodies from the tyres. Tyre damage exceeding 4 mm or that is at tyre's sidewall cannot be repaired with the tyre repair kit. 9 Warning Do not drive faster than 80 km/h. Do not use for a lengthy period. Steering and handling may be affected. If you have a flat tyre: Apply the parking brake and engage first or reverse gear.
146 Vehicle care 11. 12. 13. 8. Set the rocker switch on the compressor to I. The tyre is filled with sealant. 9. All of the sealant is pumped into the tyre. Then the tyre is inflated. Tyre pressure 3 174. When the correct pressure is obtained, switch off the compressor. 10. If a pressure of 1.5 bar is not obtained within 5 minutes, remove the tyre repair kit. Move the vehicle one tyre rotation. Reattach the tyre repair kit and continue the filling procedure for 5 minutes. If a pressure of 1.
Vehicle care Note The driving characteristics of the repaired tyre are severely affected, therefore have this tyre replaced. If unusual noise is heard or the compressor becomes hot, turn compressor off and allow to cool. Note the expiry date of the kit. After this date its sealing capability is no longer guaranteed. Pay attention to storage information on sealant bottle. Replace the used sealant bottle. Dispose of the bottle as prescribed by applicable laws.
148 Vehicle care ■ Do not start the vehicle when it is raised on the jack. ■ Clean wheel nuts and thread with a clean cloth before mounting the wheel. 2. Attach wheel wrench securely and loosen each wheel nut by half a turn. 9 Warning Do not grease wheel bolt, wheel nut and wheel nut cone. 3. Vehicle jacking points are located at the front and rear. 1. Disengage wheel nut caps with a screwdriver and remove. Pull off the wheel cover using a suitable tool. 4. Set the jack to the necessary height.
Vehicle care With the jack correctly aligned, rotate until wheel is clear of the ground. 5. Unscrew the wheel nuts. 6. Change the wheel. Spare wheel 3 149. 7. Screw on the wheel nuts. 8. Lower vehicle. 9. Install the wheel wrench ensuring that it locates securely and tighten each nut in a crosswise sequence. Tightening torque is 85 Nm (steel wheel) or 120 Nm (alloy wheel). 10. Align the valve hole in the wheel cover with the tyre valve before installing. Install wheel nut caps. 11.
150 Vehicle care 5. Unscrew knob 2 and release cable attachment 1 from spare wheel. 6. Change the wheel. 7. Position the replaced wheel at the rear of the vehicle with the outside of the wheel facing downwards. 2. Insert the wheel wrench into the aperture in the load compartment floor. 3. Rotate the wheel wrench to lower the spare wheel to the floor. 4. Withdraw spare wheel from beneath the vehicle. 8.
Vehicle care Have the defective tyre renewed or repaired as soon as possible. 2. Change the wheel. CNG vehicles Vehicles with CNG; the spare wheel is located in the load compartment. 1. Unscrew two bolts using the wheel wrench and remove spare wheel from bracket. Vehicle tools 3 142. 3. Position the replaced spare wheel onto the bracket ensuring correct alignment of the locating pin. 4. Secure spare wheel by tightening two bolts using the wheel wrench.
152 Vehicle care Jump starting Do not start with quick charger. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle. 9 Warning Be extremely careful when starting with jump leads. Any deviation from the following instructions can lead to injuries or damage caused by battery explosion or damage to the electrical systems of both vehicles. 9 Warning Avoid contact of the battery with eyes, skin, fabrics and painted surfaces.
Vehicle care 3. Connect the black lead to the negative terminal of the booster battery. 4. Connect the other end of the black lead to a vehicle grounding point, such as the engine block or an engine mounting bolt. Connect as far away from the discharged battery as possible, however at least 60 cm. Route the leads so that they cannot catch on rotating parts in the engine compartment. To start the engine: 1. Start the engine of the vehicle providing the jump. 2. After 5 minutes, start the other engine.
154 Vehicle care Caution The towing eye must only be used for towing and not for recovering the vehicle. Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wiper. Transmission in neutral. To prevent the entry of exhaust gases from the towing vehicle, switch on the air recirculation and close the windows. Seek the assistance of a workshop. After towing, unscrew the towing eye and replace the cap.
Vehicle care Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function. After using de-icing agent, have the locks regreased by a workshop. Washing The paintwork of your vehicle is exposed to environmental influences. Wash and wax your vehicle regularly. When using automatic vehicle washes, select a programme that includes waxing.
156 Vehicle care Windows and windscreen wiper blades Use a soft lint-free cloth or chamois leather together with window cleaner and insect remover. When cleaning the rear window from inside, always wipe in parallel to the heating element to prevent damage. For mechanical removal of ice, use a sharp-edged ice scraper. Press the scraper firmly against the glass so that no dirt can get under it and scratch the glass. Clean smearing wiper blades with a soft cloth and window cleaner.
Vehicle care Clean the leather upholstery with clear water and a soft cloth. In case of heavy soiling, use leather care. The instrument cluster and the displays should only be cleaned using a soft damp cloth. If necessary, use a weak soap solution. Clean fabric upholstery with a vacuum cleaner and brush. Remove stains with an upholstery cleaner. Clothing fabrics may not be colourfast. This could cause visible discolourations, especially on lightcoloured upholstery.
158 Service and maintenance Service and maintenance General information ................... 158 Recommended fluids, lubricants and parts .................................... 159 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified.
Service and maintenance Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that meet the recommended specifications. Damage resulting from the use of products not in line with these specifications will not be covered by the warranty. 9 Warning Operating materials are hazardous and could be poisonous. Handle with care. Pay attention to information given on the containers. Engine oil Engine oil is identified by its quality and its viscosity.
160 Service and maintenance temperatures the factory filled coolant provides frost protection down to approx. -37°C. This concentration should be maintained all year round. The use of additional coolant additives that intend to give additional corrosion protection or seal against minor leaks can cause function problems. Liability for consequences resulting from the use of additional coolant additives will be rejected.
Technical data Technical data Vehicle identification .................. 161 Vehicle data ............................... 162 161 Vehicle identification Vehicle Identification Number and in the floor on the front passenger side behind a cover. Identification plate The Vehicle Identification Number is visible through the windscreen The identification plate is in the engine compartment.
162 Technical data 8 = Engine type 9-11 = Vehicle-specific or countryspecific data Information on identification label: 1 = Type approval number 2 = Vehicle Identification Number 3 = Vehicle type identification code 4 = Permissible gross vehicle weight rating in kg 5 = Permissible gross train weight in kg 6 = Maximum permissible front axle load in kg 7 = Maximum permissible rear axle load in kg The combined total of front and rear axle loads must not exceed the permissible gross vehicle weight.
Technical data Engine oil viscosity grades Engine oil viscosity grade Petrol / CNG engines Diesel engines SAE 0W-30 - ✔ SAE 0W-40 ✔ - 163
164 Technical data Engine data Sales designation 1.4 1.4 1.4 Engine identifier code 1.4i 1.4Turbo 1.4CNG Number of cylinders 4 4 4 Piston displacement [cm3] 1368 1368 1368 Engine power [kW] 70 88 88 at rpm 6000 5000 5000 Torque [Nm] 127 206 206 at rpm 4500 3000 3000 Fuel type Petrol Petrol Compressed Natural Gas/Petrol recommended 95 95 95 possible 98 98 98 possible 91 91 91 Gas – – CNG Oil consumption [l/1000 km] 0.6 0.6 0.
Technical data Sales designation 1.3 Turbo 1.6 Turbo 2.0 Turbo Engine identifier code 1.3CDTI 1.6CDTI1) 2.0CDTI Number of cylinders 4 4 4 1248 1598 1956 Engine power [kW] 66 66 / 77 99 at rpm 4000 4000 3500 Torque [Nm] 200 2002) / 290 320 at rpm 1500 1500 1500 Fuel type Diesel Diesel Diesel Oil consumption [l/1000 km] 0.6 0.6 0.6 Piston displacement 1) 2) [cm3] Low / High output. Vehicles with manual transmission automated (MTA).
166 Technical data Performance The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle. Engine 1.4i 1.4Turbo 1.4CNG Manual transmission 161 172 172 Manual transmission automated – – – Maximum speed [km/h] Engine 1.3CDTI 1.6CDTI3) 2.0CDTI 158 / 1535) 164 / 1584) / 1535) Maximum speed [km/h] Manual transmission Manual transmission automated 3) 5) 4) Low / High output.
Technical data Vehicle weight Kerb weight, basic model - Van Length Roof height Engine Gross vehicle weight Kerb weight L1 H1 1.4i 1990 / 2160 1240 / 1260 1.4Turbo – / 2325 – / 1400 1.4Turbo CNG 2430 / – 1450 / – 1.3CDTI 2020 / 2290 1270 / 1290 1.6CDTI 2060 / 2330 1310 / 1330 2.0CDTI 2100 / 2370 1350 / 1370 1.4i 2010 / 2180 1260 / 1280 1.4Turbo – / 2345 – / 1420 1.4Turbo CNG 2420 / – 1470 / – 1.6CDTI 2080 / 2350 1330 / 1350 2.
168 Technical data Length Roof height Engine Gross vehicle weight Kerb weight L2 H1 1.4i 2200 / – 1300 / – 1.4Turbo 2365 / – 1440 / – 1.4Turbo CNG 2470 / 2450 1490 / 1540 1.3CDTI 2330 / – 1330 / – 1.6CDTI 2370 / – 1370 / – 2.0CDTI 2410 / – 1410 / – 1.4Turbo 2455 1455 1.6CDTI 2460 1460 2.
Technical data Kerb weight, basic model - Combi Length Roof height Engine Gross vehicle weight Kerb weight L1 H1 1.4i 2060 1350 1.4Turbo 2225 1500 1.3CDTI 2090 1380 1.6CDTI 2130 1420 2.0CDTI 2170 1460 1.4i 2160 1360 1.3CDTI 2190 1390 1.6CDTI 2230 1430 2.0CDTI 2270 1470 1.4i 2200 1400 1.4Turbo 2265 1540 1.3CDTI 2230 1430 1.6CDTI 2270 1470 2.0CDTI 2310 1510 2.
170 Technical data Kerb weight, basic model - Combo Tour Length Roof height Engine Gross vehicle weight Kerb weight L1 H1 1.4i 1940 1340 1.4Turbo 2030 1490 1.4Turbo CNG 2110 1540 1.3CDTI 1970 1370 1.6CDTI 2010 1410 2.0CDTI 2050 1450 1.4i 2210 1430 1.6CDTI 2400 1500 2.0CDTI 2440 1540 1.4i 2055 1370 1.4Turbo 2135 1490 1.3CDTI 2085 1400 1.6CDTI 2115 1430 2.0CDTI 2165 1480 2.
Technical data 171 Vehicle dimensions Type Van Wheelbase Short Long Short Long Short Long Length [mm] 4390 4740 4390 4740 4390 4740 Width without exterior mirrors [mm] 1832 1832 1832 1832 1832 1832 Width with exterior mirrors [mm] Combi 2119 2119 Combo Tour 2119 2119 2119 2119 Height (without antenna) [mm] Standard roof 1845 / High roof 2100 2125 2100 – 2100 – Length of load compartment floor 1820 [mm] 2170 – – – – Load compartment width [mm] 1230 1230 1230
172 Technical data Type Van Combi Combo Tour Wheelbase [mm] 2755 3105 2755 3105 2755 3105 Turning circle kerb to kerb [m] 11.2 12.5 11.2 12.5 11.2 12.
Technical data Capacities Engine oil Engine 1.4i 1.4Turbo 1.4CNG 1.3CDTI 1.6CDTI 2.0CDTI including Filter [l] 2.7 2.9 2.9 3.2 4.9 4.9 between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 1.0 Fuel tank Petrol/diesel, nominal capacity [l] 60 Natural gas CNG, nominal capacity [kg] Petrol, nominal capacity [l] 16.15 kg8) / 22.1 kg9) 22 8) 9) Short wheelbase version. Long wheelbase version.
174 Technical data Tyre pressures Van Comfort with up to 2 people and 100 kg luggage With full load front rear front [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 290/2.9 (42) 290/2.9 (42) 185/65 R15 92T 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (44) 195/65 R15 95T 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 270/2.7 (39) 195/60 R16 C 99/97T 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 330/3.3 (48) 360/3.
Technical data Combi Engine All Comfort with up to 3 people With full load front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 290/2.9 (42) 290/2.9 (42) 185/65 R15 92T 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (44) 195/65 R15 95T 240/2.4 (35) 300/3.0 (44) 260/2.6 (38) 320/3.2 (46) 195/60 R16 C 99/97T 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 360/3.
176 Technical data Combo Tour Engine All Comfort with up to 3 people With full load front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 290/2.9 (42) 290/2.9 (42) 185/65 R15 92T 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (44) 195/65 R15 95T 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 260/2.6 (38) 195/60 R16 C 99/97T 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 280/2.8 (41) 12) 360/3.
Customer information Customer information Vehicle data recording and pri‐ vacy ........................................... 177 Vehicle data recording and privacy Event data recorders Data storage modules in the vehicle A large number of electronic components of your vehicle contain data storage modules temporarily or permanently storing technical data about the condition of the vehicle, events and errors.
178 Customer information When using the vehicle, situations may occur in which technical data related to other information (accident report, damages on the vehicle, witness statements etc.) may be associated with a specific person possibly, with the assistance of an expert. Additional functions contractually agreed upon with the client (e.g. vehicle location in emergency cases) allow the transmission of particular vehicle data from the vehicle.
Customer information 179
180 Index A Accessories and vehicle modifications .......................... 125 Adjustable air vents ..................... 99 Airbag activation........................... 79 Airbag and belt tensioners ........... 73 Airbag deactivation .......... 46, 74, 79 Airbag system .............................. 42 Air conditioning regular operation ................................ 100 Air conditioning system ................ 96 Air intake .................................... 100 Air vents.........................
181 Child safety system for rear windows.................................... 29 Chimes......................................... 85 Cigarette lighter ........................... 67 Climate control ............................. 16 Climate control systems............... 95 Clock....................................... 64, 79 Control indicators.......................... 71 Control of the vehicle ................. 101 Controls........................................ 62 Convex shape ..............................
182 H Halogen headlights .................... 132 Hand brake................................. 112 Hazard warning flashers .............. 90 Headlight flash ............................. 88 Headlight range adjustment ........ 89 Headlights..................................... 88 Headlights when driving abroad . . 89 Head restraint adjustment ............. 8 Head restraints ............................ 33 Heated mirrors ............................. 29 Heated rear window ..................... 32 Heating ....
183 Payload......................................... 60 Performance .............................. 166 Performing work ........................ 126 Pollen filter ................................. 100 Power outlets ............................... 66 Power steering fluid.................... 129 Power windows ............................ 29 Preheating ................................... 76 Puncture..................................... 147 R Radio Frequency Identification (RFID)...............................
184 U Ultrasonic parking assist ...... 75, 116 Underseat storage ....................... 55 Unit of measurement.................... 79 Upholstery.................................. 156 Upshift.......................................... 75 Using this manual .......................... 3 V Vehicle checks............................ 126 Vehicle data................................ 162 Vehicle data recording and privacy..................................... 177 Vehicle dimensions ....................
Copyright by ADAM OPEL AG, Rüsselsheim, Germany. The information contained in this publication is effective as of the date indicated below. Adam Opel AG reserves the right to make changes to the technical specifications, features and design of the vehicles relative to the information in this publication as well as changes to the publication itself. Edition: August 2013, ADAM OPEL AG, Rüsselsheim. Printed on chlorine-free bleached paper.
