Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 19 Seats, restraints ........................... 34 Storage ........................................ 47 Instruments and controls ............. 56 Lighting ........................................ 75 Climate control ............................. 80 Driving and operating ................... 84 Vehicle care .................................
Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available under the sections "Service and Maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
Introduction Danger, Warnings and Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3.
Introduction 5
In brief In brief Vehicle unlocking Unlocking the tailgate Turn the key in the driver's door lock to the front or press button q to unlock the doors. Open the doors by pulling the handles. To unlock the leaf doors, turn the key to the vertical position or press button q. The radio remote control will only unlock the leaf doors if the key slot is in vertical position. To open the right leaf door pull the handle. To open the left leaf door, turn the handle on the inside.
In brief Seat adjustment 7 Seat backrests Seat height Turn handwheel. Do not lean on seat when adjusting. Seat adjustment 3 36, Seat position 3 35, Folding front passenger seat backrest 3 37. Lift lever and relieve some weight from seat to raise it or press down on seat with body weight to lower it. Seats 3 36, Seat position 3 35. Seat positioning Pull handle, slide seat, release handle. Move the seat until it engages. Seat adjustment 3 36, Seat position 3 35.
In brief Head restraint adjustment Seat belt Mirror adjustment Interior mirror Tilt forward to release, hold in place, adjust height and release again. Head restraints 3 34. Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle. Seat belts 3 38, Airbag system 3 40, Seat position 3 35.
In brief Exterior mirrors 9 Electric adjustment Steering wheel adjustment First select the relevant exterior mirror with the rocker switch and adjust with the four-way switch. Electric adjustment 3 30, Convex exterior mirrors 3 30, Folding exterior mirrors 3 30, Heated exterior mirrors 3 31. Unlock lever, adjust height, then engage lever and ensure it is fully locked. Do not adjust steering wheel unless vehicle is stationary and steering wheel lock has been released.
In brief
In brief Instrument panel overview 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Light switch .......................... 75 Side air vents ........................ 82 Turn and lane-change signals, headlight flash, low beam and high beam ..... 77 Horn ...................................... 57 Steering wheel controls ........ 56 Instruments .......................... 61 Windscreen wiper, windscreen washer system ... 57 Centre air vents ..................... 82 Info-Display ...........................
In brief
In brief Exterior lighting Turn light switch 7 = Off 8 = Sidelights 9 = Headlights Press light switch 0 = Courtesy lights Push button > = Front fog lights r = Rear fog lights Lighting 3 75. Headlight flash, high beam and low beam headlight flash = pull lever high beam = push lever low beam = push lever again High beam 3 75, Headlight flash 3 75. 13 Turn and lane-change signals right = lever up left = lever down Turn and lane-change signals 3 77.
In brief Hazard warning flashers Horn Washer and wiper systems Windscreen wiper Operated with the ¨ button. Hazard warning flashers 3 76. Press j. & % $ § = = = = fast slow interval wiping off Windscreen wiper 3 57, Wiper blade replacement 3 104.
In brief Windscreen washer systems Pull lever. Windscreen washer system 3 57, Washer fluid 3 103. Rear window wiper and washer system Wiper on = push lever Wiper off = pull lever Wash = push lever and hold Rear window wiper and washer system 3 58, Wiper blade replacement 3 104, Washer fluid 3 103. 15 Climate control Heated rear window, heated exterior mirrors Heating is operated by pressing the Ü button. Heated rear window 3 33.
In brief Demisting and defrosting the windows Set temperature control to warmest level. Set fan speed to highest level. Set air distribution to V. Cooling n on. Climate control system 3 80. Transmission Manual transmission automated Manual transmission Reverse: with the vehicle stationary, wait 3 seconds after depressing clutch pedal and then lift the ring under the selector lever and engage the gear.
In brief Starting off Starting the engine Check before starting off ■ Tyre pressure and condition 3 119, 3 150. ■ Engine oil level and fluid levels 3 101. ■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational. ■ Proper position of mirrors, seats, and seat belts 3 30, 3 35, 3 39. ■ Brake function at low speed, particularly if the brakes are wet.
In brief ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. ■ Close windows and sunroof. ■ The engine cooling fans may run after the engine has been switched off 3 100. ■ After running at high engine speeds or with high engine loads, operate the engine briefly at a low load or run in neutral for approx. 30 seconds before switching off, in order to protect the turbocharger.
Keys, doors and windows Keys, doors and windows Keys, locks ................................... 19 Doors ........................................... 25 Vehicle security ............................ 27 Exterior mirrors ............................ 30 Interior mirrors ............................. 31 Windows ...................................... 31 Keys, locks Keys Replacement keys The key number is specified in the Car Pass or on a detachable tag.
Keys, doors and windows Used to operate: ■ Central locking system, ■ Anti-theft locking system, ■ Anti-theft alarm system, ■ Power windows. The radio remote control has an approximate range of up to 5 metres. This range can be affected by outside influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation.
Keys, doors and windows Radio remote control synchronisation After replacing the battery, unlock the door with the key in the driver's door lock. The radio remote control will be synchronised when you switch on the ignition. Unlocking Central locking system with key activation 21 Central locking system with radio remote control Central locking system Unlocks and locks doors, load compartment and fuel filler flap. Note In the event of an accident of a certain severity, the vehicle unlocks automatically.
Keys, doors and windows Locking Close doors, load compartment and fuel filler flap. If the driver's door is not closed properly, the central locking system will not work. Central locking system with radio remote control Fault in radio remote control Central locking system with key activation Press button p. Turn the key in the driver's door lock rearwards. Unlocking Turn the key in the driver's door lock towards front of vehicle. The entire vehicle is unlocked.
Keys, doors and windows Fault in central locking system Central locking and the tailgate Unlocking Turn the key in the driver's door lock towards front of vehicle. The other doors can be opened by pulling the interior handle (not possible if the anti-theft locking system is active). The load compartment and fuel filler flap remain locked. To deactivate the anti-theft locking system, switch on the ignition 3 27. Locking With the driver’s door open, press the lock button of one of the other doors.
Keys, doors and windows Relock the tailgate by closing it and turning the key to the horizontal or vertical position. In the horizontal position, the tailgate will be unlocked the next time the vehicle is unlocked via the central locking system. Central locking and the leaf doors The central locking system and antitheft locking system for the doors cannot be operated via the leaf doors lock.
Keys, doors and windows Child locks Doors Sliding door 9 Warning 25 To open the sliding doors, pull the handle and slide the door towards the rear of the vehicle. Opening from inside If the vehicle is parked on a downhill slope, open sliding doors may move accidentally on account of their weight. Close the sliding doors before driving off. 9 Warning Use the child locks whenever children are occupying the rear seats.
Keys, doors and windows Load compartment Tailgate Opening Note The installation of certain heavy accessories onto the tailgate may affect its ability to remain open. Leaf doors Closing Press the button to open the tailgate. 9 Warning Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases could enter the vehicle. Use the interior handle. Do not press the button under the moulding while closing as this will unlock the tailgate again.
Keys, doors and windows When the doors are open 180°, the rear exterior lighting is covered. Therefore, only open the doors until they engage when it is dark outside. When closing, make sure that the stop lug properly engages in the guide rail. Closing Vehicle security Anti-theft alarm system 27 Activating with the radio remote control It monitors: ■ Doors, load compartment, bonnet, ■ Passenger compartment, ■ Vehicle inclination, e.g. if it is raised, ■ Ignition.
Keys, doors and windows Activation without monitoring of passenger compartment and vehicle inclination 2. Press button in front of the courtesy light (with ignition off); LED in the hazard warning flashers button flashes for a maximum of 10 seconds. 3. Close doors. 4. Activate the anti-theft alarm system. The LED illuminates. After approx. 10 seconds, the system is armed. The LED flashes until the system is deactivated.
Keys, doors and windows If the alarm is triggered when the driver’s door is opened, deactivate the anti-theft alarm system by switching on the ignition. Opening and closing tailgate/ leaf doors with activated antitheft alarm system To unlock: 1. Tailgate: Turn key clockwise all the way past the horizontal position. The tailgate is unlocked and monitoring of the passenger compartment and vehicle inclination are disabled. Leaf doors: Turn key anti-clockwise all the way past the vertical position.
Keys, doors and windows Exterior mirrors Electric adjustment Folding Manual Convex shape The convex exterior mirror reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the ability to estimate distances. Manual adjustment Select the relevant exterior mirror with the rocker switch and adjust with the four-way switch. Adjust mirrors by swivelling lever in required direction.
Keys, doors and windows Heated Operated by pressing the Ü button. Heating works with the engine running. 31 Interior mirrors Windows Manual anti-dazzle Manual windows To reduce dazzle, adjust the lever on the underside of the mirror housing. The door windows can be opened or closed with the window winders.
Keys, doors and windows Window in the sliding doors Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move. Power windows can be operated when the ignition key is in position 1 in the ignition switch. Illumination of the rocker switches indicates operational readiness. After switching off the ignition, the window operation is disabled, when the driver's door is opened. To open = Release joint and push outwards. To close = Pull joint and engage.
Keys, doors and windows 3. Close the window completely and operate the button for 5 more seconds. 4. Open the window completely and operate the button for 1 more second. 5. Repeat this for each window. Heated rear window Press p until all windows are closed. Overload If the windows are repeatedly operated at short intervals, the window operation is disabled for some time. Fault If the windows cannot be opened or closed automatically, activate the window electronics as follows: 1. Close doors. 2.
Seats, restraints Seats, restraints Head restraints ............................ 34 Front seats ................................... 35 Seat belts ..................................... 38 Airbag system .............................. 40 Child restraints ............................. 41 Head restraints Adjustment Position Head restraints on front and outer rear seats 9 Warning Only drive with the head restraint set to the proper position.
Seats, restraints Head restraints on centre rear seats Removing head restraint 35 Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. To fold the backrest, press the detent springs on the guide sleeves to release the head restraint and push it all the way down. Release both catches by pressing and withdraw head restraint. The rear centre head restraint cannot be removed. ■ Sit with buttocks as far back against the backrest as possible.
Seats, restraints ■ Sit with shoulders as far back against the backrest as possible. Set the backrest to an angle so that it is possible to reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel. Do not tilt the backrest too far back. We recommend a maximum angle of approx. 25°. ■ Adjust the steering wheel 3 56. ■ Set the seat high enough to have a clear field of vision on all sides and on all display instruments.
Seats, restraints 37 Seat height Seat folding Heating Lift lever and relieve some weight from seat to raise it or press down on seat with body weight to lower it. Lift release lever and tilt backrest forwards. Activate heating by pressing ß button for the seat with the ignition on. LED in button ß on: relevant front seat heating on. Seat heating is operational when the engine is running. For vehicles with natural gas operation, only switch ß is available.
Seats, restraints Seat belts The belts are locked during heavy acceleration or deceleration of the vehicle for the safety of the occupants. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves. Seat belts are designed to be used by only one person at a time. They are not suitable for people younger than 12 years of age or smaller than 150 cm. Child restraint system 3 41.
Seats, restraints Triggered belt tensioners must be replaced by a workshop. Belt tensioners can only be triggered once. Note Do not affix or install accessories or other objects that may interfere with the operation of the belt tensioners. Do not make any modifications to belt tensioner components as this will invalidate the vehicle type approval. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing. Height adjustment 39 Do not adjust while driving.
Seats, restraints Airbag system The airbag system consists of a number of individual systems. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner. Note The airbag systems and belt pretensioner control electronics are located in the centre console area. Do not put any magnetic objects in this area.
Seats, restraints 9 Warning Optimum protection is only provided when the seat is in the proper position 3 35. Keep the area in which the airbag inflates clear of obstructions. Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The side airbag system consists of an airbag in each front seat backrest and in the rear outboard seat backrests. This can be identified by the word AIRBAG.
Seats, restraints Selecting the right system The rear seats are the most convenient location to fasten a child restraint system. Children should travel facing rearwards in the vehicle as long as possible. This makes sure that the child's backbone, which is still very weak, is under less strain in the event of an accident. Children under the age of 12 years that are smaller than150 cm are only allowed to travel in a restraint system that is suitable for the child.
Seats, restraints 43 Child restraint installation locations Permissible options for fitting a child restraint system Weight and age class On front passenger seat On rear outboard seats On rear centre seat Group 0: up to 10 kg or approx. 10 months X U+ U Group 0+: up to 13 kg or approx. 2 years X U+ U Group I: 9 to 18 kg or approx. 8 months to 4 years X U+ U Group II: 15 to 25 kg or approx. 3 to 7 years X U U Group III: 22 to 36 kg or approx.
Seats, restraints Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to 10 kg E ISO/R1 X IL X Group 0+: up to 13 kg E ISO/R1 X IL X D ISO/R2 X IL X C ISO/R3 X IL X D ISO/R2 X IL X C ISO/R3 X IL X B ISO/F2 X IL X B1 ISO/F2X X IL X A ISO/F3 IL X Group I: 9 to 18 kg X IL = Suitable for particular ISOFIX restraint systems of the 'sp
Seats, restraints ISOFIX size class and seat device A – ISO/F3 B – ISO/F2 B1 – ISO/F2X C – ISO/R3 D – ISO/R2 E – ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Rear-facing child restraint system for children of maximum size in the weight class up to 13 kg.
Seats, restraints Isofix child restraint systems The mounting eyes for the ISOFIX child restraint system are located on the rear, outer seats between the seat back and the seat cushion. Fasten permitted ISOFIX child restraint systems to the mounting brackets. Closely follow the installation instructions accompanying the ISOFIX child restraint system.
Storage Storage Storage compartments 47 Sunglasses storage Glovebox Storage compartments ................ 47 Load compartment ....................... 49 Roof rack system ......................... 54 Loading information ..................... 54 The glovebox features a pen holder. In vehicles with Infotainment system, the telematics unit can be located in the glovebox. The glovebox should be closed whilst driving. Fold down and open. Do not use for storing heavy objects.
Storage Overhead console Underseat storage Centre console storage Coin holder The stowage compartment above the front seats can hold a maximum load of 15 kg. The mesh packets above the doors can only hold light objects. 9 Warning Secure objects to prevent them from falling out and causing injury. Lift at recessed edge and pull out. Maximum load: 1 kg. To close, push in and engage. Located in the centre console.
Storage 49 Load compartment Folding down rear backrests Push the rear, outer head restraint down completely or remove it. Push the rear, centre head restraint down completely 3 34. To fold one or both of the rear seat backrests, press the button at the top to release the backrest and fold it onto the seat cushion. Alternatively: Remove the rear, outer head restraints. Push the rear, centre head restraint down completely 3 34. Hook seat belt buckles on rear seat backrests.
Storage To close Removing Safety net The safety net can be installed behind the rear seats or, if the rear seat backrests are folded down, behind the front seats. Passengers must not be transported behind the safety net. Installation Pull cover towards rear of vehicle using handle and hook into side retainers. To open Unhooked the closed cover at the rear. It rolls up automatically. Open cover. Press button at right side of cartridge and engage by pushing right-hand end piece to the left.
Storage Behind the rear seats Behind front seats 51 9 Warning The brackets must not be used as lashing eyes to prevent objects that are being transported from sliding around. Removal Fold down both rear seat backrests. Hook tensioning straps into lashing eyes in floor and tighten by pulling on the loose end of the strap. Reposition and engage the backrests. Pull up both rear seat cushions and fold down rear seat backrests.
Storage To enlarge the load compartment, the grille can be moved forwards on the front passenger’s side. Push the head restraint of the front passenger seat down as far as it will go 3 34. Tilt front passenger’s seat backrest forward by raising release lever and push down to lock in position. Engage lever on load compartment grille at top position, as shown in illustration. Position load compartment grille above retainer in front passenger’s seat backrest.
Storage The warning triangle is kept in the compartment behind the driver’s seat. When the vehicle is being loaded, please ensure that nothing protrudes over the bottom edge of the opening. Disengage flap by pressing retaining lug and remove. 53 Release flap by pressing retaining lugs. Van First aid kit Combo Van The first-aid kit (cushion) is kept in the compartment behind the driver’s seat. When the vehicle is being loaded, please ensure that nothing protrudes over the bottom edge of the opening.
Storage Roof rack system Loading information Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. Follow the installation instructions and remove the roof rack when not in use. ■ Heavy objects in the load compartment should be placed against the seat backrests. Ensure the backrests are securely engaged. If objects can be stacked, the heavier objects should be placed at the bottom.
Storage 9 Warning Always make sure that the load in the vehicle is securely stowed. Otherwise objects can be thrown around inside the vehicle and cause personal injury or damage to the load or car. ■ Do not cover the air outlets when stowing objects in the load compartment. ■ The payload is the difference between the permitted gross vehicle weight (see identification plate 3 138) and the EC kerb weight.
Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 56 Warning lights, gauges and indicators ..................................... 61 Information displays ..................... 70 Vehicle messages ........................ 74 Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked.
Instruments and controls Horn Windscreen wiper/washer Windscreen wiper Adjustable wiper interval To set the wiper interval to a value between 2 and 15 seconds: Lever to interval operation $, lever to §, wait for required interval delay, lever to interval operation again $. The selected interval will remain stored until the next time it is changed or until the ignition is switched off. After turning on the ignition and setting the lever to $, the interval is set to 7 seconds. Windscreen washer Press j.
Instruments and controls Pull lever. Washer fluid is sprayed onto the windscreen and the wiper wipes a few times. Outside temperature Rear window wiper/washer Push lever forwards. The rear window wiper wipes in interval mode. Switch off by pulling the lever. If the lever is held forwards, washer fluid is sprayed onto the rear window. Do not use if the rear window is frozen. Switch off in car washes. A drop in temperature is indicated immediately and a rise in temperature after a time delay.
Instruments and controls Clock Power outlets Time display in odometer To switch between trip odometer and time display give reset knob a short press. Setting the time On the clock display, press the setting knob on the instrument for approx. 2 seconds. The flashing value is set by pressing briefly. Press for about 2 seconds again to switch to the next setting and at the end to exit setting mode. 59 current-delivering accessories, e.g. electrical charging devices or batteries.
Instruments and controls With the ignition on, press in cigarette lighter. It switches off automatically once the element is glowing. Pull out lighter. Front ashtray Rear ashtray Open the ashtray cover to the resistance point. To empty, open the ashtray cover fully beyond its resistance point, causing the insert to lift. Grip both sides of the ashtray insert and pull upwards. To enlarge the storage compartment remove the ashtray completely. In the rear centre console.
Instruments and controls Warning lights, gauges and indicators Odometer Speedometer Indicates vehicle speed. 61 To reset, press button with ignition switched on and trip odometer activated and hold down for approximately one second. Vehicles with clock in odometer With the ignition switched off, briefly press the reset knob to display the number of kilometres driven for approx. 15 seconds. The bottom line displays the recorded distance.
Instruments and controls Tachometer Fuel gauge Natural gas operation Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Displays the fuel level in the tank. If the fuel level is too low, Y lights up. When the light flashes, refuel immediately. Never run the tank dry. On vehicles with auxiliary heating, regularly check the petrol level as it consumes petrol even during natural gas operation.
Instruments and controls Display: 1/1 - Tank pressure approx. 200 bar 3/4 - Tank pressure approx. 150 bar 1/2 - Tank pressure approx. 100 bar 1/4 - Tank pressure approx. 50 bar In order to achieve the maximum range in natural gas operation, we recommend that you make use of the entire reserve area. Fuel selector Pressing button Y switches between petrol and natural gas operation. Switching is not possible at high loads (e.g. strong acceleration, running at full throttle).
Instruments and controls Engine coolant temperature gauge Caution If engine coolant temperature is too high, stop vehicle, switch off engine. Danger to engine. Check coolant level. For physical reasons, the engine temperature gauge shows the coolant temperature only if the coolant level is adequate. During operation the system is pressurised. The temperature may therefore rise briefly to over 100 °C. Displays the coolant temperature.
Instruments and controls Transmission display The mode or selected gear is shown in the transmission display. R = Reverse gear N = Neutral position A = Manual transmission automated: automatic mode 1 - 5 = Current gear, manual transmission automated, manual mode Control indicators The control indicators described are not present in all vehicles. The description applies to all instrument versions. When the ignition is switched on, most control indicators will illuminate briefly as a functionality test.
Instruments and controls Control indicators in the instrument cluster
Instruments and controls Turn signal Charging system O illuminates or flashes green. p illuminates or flashes red. Illuminates when the ignition is switched on and goes out shortly after the engine starts. Flashes The control indicator flashes if a turn signal is or the hazard warning flashers are activated. Rapid flashing: failure of a turn signal light or associated fuse, failure of turn signal light on trailer. Bulb replacement 3 105. Fuses 3 113. Turn signals 3 77.
Instruments and controls Flashes with switched on ignition Fault in the immobiliser system. The engine cannot be started 3 29. Brake and clutch system R illuminates or flashes red. Illuminates Illuminates when the parking brake is released if the brake and clutch fluid level is too low 3 103. 9 Warning Stop. Do not continue your journey. Consult a workshop. Illuminates after the ignition is switched on if the parking brake is applied 3 93.
Instruments and controls Illuminates when the engine is running Caution Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels. 1. Depress clutch. 2. Select neutral gear, set selector lever to N. 3. Move out of the flow of traffic as quickly as possible without impeding other vehicles. 4. Switch off ignition. 9 Warning When the engine is off, considerably more force is needed to brake and steer.
Instruments and controls Information displays Triple-Info-Display Graphic-Info-Display, Colour-Info-Display Functions are selected and executed in the menu on the display using the four-way button, the multifunction button on the infotainment system or the buttons on the steering wheel. Selecting with the four-way button Displays time, outside temperature and date or Infotainment system (when it is on).
Instruments and controls Selecting with the multifunction control Selecting with the steering wheel buttons Turn the multifunction control to highlight menu items or commands and to select function areas. Press the multifunction control to select the highlighted item or confirm a command. To exit a menu, turn the multifunction control until Return or Main appear and select. Select menu options via the menus using the buttons.
Instruments and controls System settings Setting date and time On Infotainment systems with navigation, time and date are also harmonised upon receipt of a GPS satellite signal. The function is activated by ticking the field in front of Synchron. clock automatical. in the Time, Date menu. Language selection Press the Main button of the Infotainment system. Press the Settings button on the Infotainment system. For Infotainment system CD 30, no menu may be selected.
Instruments and controls Setting units of measure Selection is indicated by a 6 in front of the menu item. In systems with voice output, when the language setting of the display is changed the system will ask whether the announcement language should also be changed - see Infotainment system manual. Select menu item Units from the Settings menu. Select the desired unit. Selections are indicated by a o in front of the menu item.
Instruments and controls Always day design: black text on light background. Always night design: white text on dark background. Selection is indicated by a o in front of the menu item. Ignition logic See Infotainment system manual. Vehicle messages Warning chimes When starting the engine or whilst driving ■ If seat belt is not fastened. ■ If the speed programmed at the factory is exceeded.
Lighting Lighting Exterior lighting Light switch Exterior lighting ............................ 75 Interior lighting ............................. 78 Lighting features .......................... 79 75 Tail lights Tail lights are illuminated together with headlights and sidelights. High beam Turn light switch: 7 = OFF 8 = Sidelights 9 = Headlights Control indicator 9 3 69.
Lighting Headlight range adjustment Manual headlight range adjustment 2 = All seats occupied and load compartment laden 3 = Driver's seat occupied and load compartment laden Combo van 0 = Seats occupied 1 = Seats occupied and half load in load compartment 2 = Seats occupied and full load in load compartment 3 = Driver's seat occupied and full load in load compartment Headlights when driving abroad Rotate the adjuster wheel to the required position to adjust the dipped beam range to vehicle loading an
Lighting Turn and lane-change signals Switch the turn signal off manually by moving the lever slightly. The vehicle rear fog light is deactivated when towing. Front fog lights Misted light covers 77 The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing. The mist disappears quickly by itself; to help, switch on the headlights.
Lighting Interior lighting Instrument panel illumination control Interior lights Load compartment lighting During entry and exit of the vehicle, the front and centre courtesy lights automatically come on and then switch off after a delay. The lighting switches on when opened.
Lighting Lighting features Centre console lighting Spotlight in interior mirror housing. Daylight-dependent, automatically regulated centre console lighting. Battery discharge protection Some consumers such as the interior lighting switch themselves off after approx. 30 minutes if the ignition is off in order to protect the battery charge.
Climate control Climate control Climate control systems ............... 80 Air vents ....................................... 82 Maintenance ................................ 82 Climate control systems Heating and ventilation system Heating will not be fully effective until engine has reached normal operating temperature. Fan speed Adjust the air flow by switching the fan to the desired speed.
Climate control ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J. Air conditioning system Cooling n Operated with the n button and is functional only when the engine and fan are running. The air conditioning system cools and dehumidifies (dries) as soon as the outside temperature is slightly above the freezing point. Therefore condensation may form and drip from under the vehicle.
Climate control Air vents Maintenance Adjustable air vents Air intake At least one air vent must be open while cooling is on in order to prevent the evaporator from icing up due to lack of air movement. To close the vent, turn the adjuster wheel to left or right to its stop. 9 Warning Set the direction of the air flow by turning the adjuster wheel from right to left and raise or lower the horizontal slats. Do not attach any objects to the slats of the air vents.
Climate control Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low.
Driving and operating Driving and operating Driving hints ................................. 84 Starting and operating ................. 84 Engine exhaust ............................ 86 Manual transmission .................... 88 Manual transmission automated .................................... 89 Brakes .......................................... 92 Fuel .............................................. 94 Towing .........................................
Driving and operating Ignition switch positions Starting the engine 85 Starting the vehicle at low temperatures The start of the engine without additional heaters is possible down to -25 °С for diesel engines and -30 °C for petrol engines. Required is an engine oil with the correct viscosity, the correct fuel, performed services and a sufficiently charged battery. With temperatures below -30 °C the manual transmission automated need a warming phase of approx. 5 minutes.
Driving and operating Parking ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. ■ Always apply parking brake without pressing release button. Apply as firmly as possible on downhill or uphill slopes. Depress the foot brake at the same time to reduce operating force. ■ Switch off the engine and ignition. Turn the steering wheel until the steering wheel lock engages.
Driving and operating 87 consumption may be higher during this period. The emission of smells and smoke during this process is normal. Stopping the journey or switching off the engine during cleaning is not recommended. Under certain driving conditions, e.g. short distances, the system cannot clean itself automatically. If the filter requires cleaning and previous driving conditions did not enable automatic cleaning, control indicator ! flashes.
Driving and operating Caution Manual transmission It is not advisable to drive with the hand resting on the selector lever. Fuel grades other than those listed on pages 3 94, 3 143 could damage the catalytic converter or electronic components. Unburnt petrol will overheat and damage the catalytic converter. Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing.
Driving and operating Manual transmission automated The Easytronic transmission permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control. Transmission display Shows the mode and current gear. If the Winter programme is activated, T is illuminated. Starting the engine Depress the foot brake when starting the engine. If the foot brake is not depressed, "N" flashes in the transmission display and the engine cannot be started.
Driving and operating Manual mode In manual mode, a gear can be selected manually by tapping the selector lever to the + or - position. The transmission display indicates the current gear. If the engine speed is too low the manual transmission automated will automatically shift to a lower gear even in Manual mode. If a higher gear is selected when the running speed is too low, or a lower gear when the speed is too high, no shift is carried out.
Driving and operating Winter mode T ■ switching to manual mode ■ when clutch temperature is too high Without kickdown this automatic shift is not effected in manual mode. Kickdown Fault Activate the Winter mode if you have problems starting off on a slippery road surface. Activation Press the T button. The transmission switches to automatic mode. The vehicle starts off in 2nd gear.
Driving and operating If the cause of the fault is not a discharged battery, seek the assistance of a workshop. 5. Using a flat-head screwdriver, turn the adjusting screw under the cap clockwise until clear resistance can be felt. The clutch has now been disengaged. Caution Do not turn beyond the resistance since this could damage the transmission. 6. Refit cleaned cap. The cap must be in full contact with the housing.
Driving and operating ABS starts to regulate brake pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even during hard braking. ABS control is made apparent through a pulse in the brake pedal and the noise of the regulation process. For optimum braking, keep the brake pedal fully depressed throughout the braking process, despite the fact that the pedal is pulsating. Do not reduce the pressure on the pedal.
Driving and operating Brake assist If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking). Maintain steady pressure on the brake pedal for as long as full braking is required. Maximum brake force is automatically reduced when the brake pedal is released. Fuel Fuel for diesel engines Fuel for petrol engines Only use unleaded fuel that complies with DIN EN 2281). Equivalent standardised fuels with an ethanol content of max.
Driving and operating (high) has approx. 87 - 99 %. Biogas with the same methane content can also be used if it has been chemically prepared and desulphurised. Only use natural gas or biogas that complies with DIN 51624. Liquid gas or LPG must not be used. Refuelling 9 Danger Before refuelling, switch off engine and any external heaters with combustion chambers (identified by sticker on fuel filler flap). Switch off any mobile phones.
Driving and operating Caution Wipe off any overflowing fuel immediately. Natural gas refuelling The refuelling procedure must be completed, i.e. the filler neck must be vented. Refit the protective cap. The capacity of the natural gas tank depends on outside temperature, filling pressure and type of refuelling system.
Driving and operating driving with approx. 2/3. Cold starts and acceleration phases are also taken into consideration. The specification of CO2 emission is also a constituent of the directive. The figures given must not be taken as a guarantee for the actual fuel consumption of a particular vehicle. Furthermore, fuel consumption is dependent on personal driving style as well as road and traffic conditions. All values are based on the EU base model with standard equipment.
Driving and operating If the trailer starts snaking, drive more slowly, do not attempt to correct the steering and brake sharply if necessary. When driving downhill, drive in the same gear as if driving uphill and drive at a similar speed. Adjust tyre pressure to the value specified for full load 3 150. Trailer towing Trailer loads The permissible trailer loads are vehicle and engine-dependent maximum values which must not be exceeded.
Vehicle care Vehicle care General Information ..................... 99 Vehicle checks ........................... 100 Bulb replacement ....................... 105 Electrical system ........................ 113 Vehicle tools .............................. 118 Wheels and tyres ....................... 119 Jump starting ............................. 128 Towing ....................................... 130 Appearance care .......................
Vehicle care ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft alarm system. Vehicle checks Performing work Putting back into operation Following must be done if the vehicle is putting back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir. ■ Check the engine oil level.
Vehicle care Pull the release lever and return it to its original position. Secure the bonnet support. Lift the safety catch upwards and open the bonnet. Air intake 3 82. specification of oil is used. Recommended fluids and lubricants 3 135. Check with the vehicle on a level surface. The engine must be at operating temperature and switched off for at least 5 minutes. Pull out the dipstick, wipe it clean, insert it to the stop on the handle, pull out and read the engine oil level.
Vehicle care We recommend to use the same engine oil that is filled in. The engine oil level must not exceed the MAX mark on the dipstick. Caution Overfilled engine oil must be drained or suctioned out. When the engine oil level has dropped to the MIN mark, top up engine oil. Capacities 3 148. Fit the cap on straight and tighten it. Engine coolant The coolant provides freeze protection down to approx. -28 °C. Caution Only use approved antifreeze.
Vehicle care concentration checked and have the cause of the coolant loss remedied by a workshop. Washer fluid Caution Only washer fluid with a sufficient antifreeze concentration provides protection at low temperatures or a sudden drop in temperature. Brakes A squealing noise indicates that the brake lining is at its minimum thickness. Continued driving is possible but have the brake lining replaced as soon as possible.
Vehicle care Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point. Laying up the vehicle for more than 4 weeks can lead to battery discharge. Disconnect the clamp from the negative terminal of the vehicle battery. Ensure the ignition is switched off before connecting or disconnecting the vehicle battery.
Vehicle care Wiper blade on the rear window Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. 105 the relay box in front of the fuse box upwards out of the guides. Pull off the air hose on the air filter on the right. Halogen headlights Lift wiper arm. Disengage wiper blade as shown in illustration and remove.
Vehicle care Low beam 2. Push bulb on plug connector downward. 3. Remove bulb with connector from reflector housing. 1. Rotate the cap anticlockwise and remove. High beam 1. Rotate protective cover anticlockwise and remove. 2. Detach plug connector from bulb. 4. Detach plug connector from bulb base. 5. Plug the plug onto the new bulb. 6. Insert the bulb with connector so that the lug engages in the recess in the reflector. 7. Place headlamp protective cover in position and close.
Vehicle care 3. Disengage spring clip from retainer by moving it forward and swivelling to the side. 4. Remove bulb from reflector housing. 5. When installing the new bulb, insert lugs in the reflector recesses. 6. Install spring clip, plug connector onto bulb. 7. Install protective cover. 107 Side lights 1. Rotate high beam protective cover anticlockwise and remove. 2. Detach plug connector from high beam bulb. 3. Remove bulb from reflector and renew bulb. 4. Insert bulb socket in reflector.
Vehicle care 5. Attach connector to main beam bulb. 6. Place protective cover in position and close. 3. Disengage spring clip by swivelling to the side. 4. Remove bulb from reflector housing. Front turn signal lights Ellipsoidal headlights Headlights have separate systems for low beam (inner bulbs) and high beam (outer bulbs). Low beam 1. Remove protective cover by pressing the catch and pulling the cover downward and off. 2. Detach plug connector from bulb. 5.
Vehicle care Front turn signal lights 109 2. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb. 3. Insert bulb holder in reflector, rotate clockwise to engage. Tail lights 5-door passenger vehicle 3. Insert bulb holder in reflector, rotate clockwise to engage. Fog lights 1. Rotate bulb holder anti-clockwise to disengage. Have bulbs replaced by a workshop. 1. Disengage cover by pressing retaining lugs and remove.
Vehicle care After bulb replacement, check the tail lights for proper functionality: switch on the ignition, operate the brake, switch on the sidelights. Side turn signal lights Have bulbs replaced by a workshop. Number plate light 2. Detach plug connector from bulb mounting. 3. Hold bulb housing from the outside; slacken two retaining nuts with the wheel bolt spanner 3 118 and unscrew by hand. 4. Detach bulb housing. 5.
Vehicle care Interior lights Front courtesy light 2. Press bulb slightly towards spring clip and remove. 3. Insert new bulb. 4. Insert lamp insert and secure using a screwdriver. 3. Insert new bulb. 4. Mount lens and engage in position. 1. Prise lamp out with a screwdriver. 2. Press bulb slightly towards spring clip and remove.
Vehicle care Front courtesy light, reading lights 1. Disengage lens using a screwdriver and remove. 2. Remove bulb and renew. 3. Mount lens and engage in position. Load compartment light 1. Prise lamp out with a screwdriver. 2. Press bulb slightly towards spring clip and remove. 3. Insert new bulb. 4. Insert lamp in opening and engage in position. Instrument panel illumination Have bulbs replaced by a workshop.
Vehicle care Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. The fuse box is located in the engine compartment. Before replacing a fuse, turn off the respective switch and the ignition. 113 Some functions are protected by several fuses. Fuses may also be inserted without existence of a function.
Vehicle care Fuse boxes of vehicles with engine Z13DTJ Disengage the cover, lift it upwards and remove.
Vehicle care No. Circuit No. Circuit No.
Vehicle care No.
Vehicle care No. Circuit No. Circuit No.
Vehicle care No. Circuit Vehicle tools 43 High beam (left) Tools 44 High beam (right) 45 Ventilation fan Combo 46 Engine control unit 47 Heated rear window 48 Starter 49 EPS The vehicle tools are secured to the jack with rubber bands.
Vehicle care Wheels and tyres Tyre condition, wheel condition The vehicle tools are secured to the jack with rubber bands. Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage. Seek the assistance of a workshop in the event of damage or unusual wear.
Vehicle care Remove the valve cap key from the fuel filler flap and use it to unscrew the valve cap. Incorrect tyre pressures will impair safety, vehicle handling, comfort and fuel economy and will increase tyre wear. 9 Warning If the pressure is too low, this can result in considerable tyre warmup and internal damage, leading to tread separation and even to tyre blow-out at high speeds. Tread depth Tyre pressure 3 150 and on the label on the inside of the fuel filler flap.
Vehicle care Wheel covers Wheel covers and tyres that are factory approved for the respective vehicle and comply with all of the relevant wheel and tyre combination requirements must be used. If the wheel covers and tyres used are not factory approved, the tyres must not have a rim protection ridge. Wheel covers must not impair brake cooling. 9 Warning Use of unsuitable tyres or wheel covers could lead to sudden pressure loss and thereby accidents.
Vehicle care 4. Screw the compressor air hose to the connection on the sealant bottle. 5. Fit the sealant bottle in the retainer on the compressor. Set the compressor near the tyre in such a way that the sealant bottle is upright. 6. Unscrew valve cap from defective tyre. 9. Plug the compressor connector into the accessory socket or the cigarette lighter socket. 10. Switch on ignition. To avoid discharging the battery, we recommend running the engine. 3.
Vehicle care 6 bar. Then the pressure starts to drop. All of the sealant is pumped into the tyre. Then the tyre is inflated. 13. All of the sealant is pumped into the tyre. Then the tyre is inflated. 14. The prescribed tyre pressure should be obtained within 10 minutes. Tyre pressure 3 150. When the correct pressure is obtained, switch off the compressor. 15. 16. 17. If the prescribed tyre pressure is not obtained within 10 minutes, remove the tyre repair kit. Move the vehicle one tyre rotation. 18.
Vehicle care Note The driving characteristics of the repaired tyre is severely affected, therefore have this tyre replaced. If unusual noise is heard or the compressor becomes hot, turn compressor off for at least 30 minutes. The built-in safety valve opens at a pressure of 7 bar. Note the expiry date of the kit. After this date its sealing capability is no longer guaranteed. Pay attention to storage information on sealant bottle. Replace the used sealant bottle.
Vehicle care 125 2. Install the wheel wrench ensuring that it locates securely and slacken each bolt by half a turn. On some versions, the wheel cover is removed together with the wheel bolts. For wheel covers with visible wheel bolts, the cover can remain on the wheel. The retaining rings at the wheel bolts must not be removed. Alloy wheels: Disengage wheel bolt caps with a screwdriver and remove. To protect the wheel, place a soft cloth between the screwdriver and the alloy wheel.
Vehicle care 4. Set the jack to the necessary height before positioning it directly below the jacking point in a manner that prevents it from slipping. Position the jack arm so that the jack claw grips the vertical web in the recess. The edge of the jack base must be planted firmly and vertically in line with the contact point. Rotate handle until wheel is clear of the ground. 5. Unscrew the wheel bolts. If there are lock washers on the wheel bolts, these must not be removed. 6. Change the wheel. 7.
Vehicle care 127 11. Stow the replaced wheel 3 121 and the vehicle tools 3 118. 12. Check the tyre pressure of the installed tyre and also the wheel bolt torque as soon as possible. Have the defective tyre renewed or repaired. Spare wheel Some vehicles are equipped with a tyre repair kit instead of a spare wheel. The spare wheel can be classified as a temporary spare wheel depending on the size compared to the other mounted wheels and country regulations. The spare wheel has a steel rim.
Vehicle care Temporary spare wheel 7. 8. 9. 10. If a full specification wheel is stowed, do not fit the spacer ring between the wheel and the vehicle underbody. Change the wheel. Lift the spare wheel holder, insert the safety cable. Lift the spare wheel holder and engage in the catch. The open side of the catch must point towards the rear. Turn the hexagon bolt in the load compartment floor with the wheel bolt wrench to raise the spare wheel holder all the way up.
Vehicle care ■ A discharged battery can already freeze at a temperature of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Wear eye protection and protective clothing when handling a battery. ■ Use a booster battery with the same voltage (12 Volts). Its capacity (Ah) must not be much less than that of the discharged battery. ■ Use jump leads with insulated terminals and a cross section of at least 16 mm2 (25 mm2 for diesel engines).
Vehicle care Towing Attach a tow rope – or better still a tow rod – to the towing eye. The towing eye must only be used for towing and not recovering the vehicle. Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wiper. Transmission in neutral. Switch on the hazard warning flashers on both vehicles. Towing the vehicle Screw in the towing eye as far as it will go until it stops in a horizontal position.
Vehicle care Manual transmission automated 3 89. After towing, unscrew the towing eye and refit the cover. Towing another vehicle Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function.
Vehicle care If using a car wash, comply with the car wash manufacturer's instructions. The windscreen wipers and rear window wiper must be switched off. Remove antenna and external accessories such as roof racks etc. If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out. Clean edges and folds on opened doors and the bonnet as well as the areas they cover. Have the door hinges of all doors greased by a workshop.
Vehicle care After the underbody is washed, check the underbody and have it waxed if necessary. Bitumen/rubber materials could damage the PVC coating. Have underbody work carried out by a workshop. Before and after winter, wash the underbody and have the protective wax coating checked. Natural gas system Do not direct the steam jet or highpressure jet towards natural gas system components.
Service and maintenance Service and maintenance General information ................... 134 Recommended fluids, lubricants and parts .................................... 135 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified.
Service and maintenance Fixed service interval When service is due, InSP appears in the odometer display for approximately 10 seconds when the ignition is switched on. Have the next service performed by a workshop within one week or 500 km (whichever occurs first). Flexible service interval The service interval is based on several parameters depending on usage and calculated using these parameters.
Service and maintenance aging control, whereas viscosity grade gives information on the oil's thickness over a temperature range. Dexos is the newest engine oil quality that provides optimum protection for gasoline and diesel engines. If it is unavailable, engine oils of other listed qualities have to be used. Recommendations for gasoline engines are also valid for Compressed Natural Gas (CNG), Liquified Petroleum Gas (LPG) and Ethanol (E85) fueled engines.
Service and maintenance Brake fluid should be stored in a sealed container to avoid water absorption. Ensure brake fluid does not become contaminated.
Technical data Technical data Vehicle identification .................. 138 Vehicle data ............................... 140 Vehicle identification Identification plate Vehicle Identification Number The identification plate is located on the front right door frame. The Vehicle Identification Number is stamped on the identification plate and on the floor pan, under the floor covering, visible under a cover.
Technical data In other versions the type plate is attached to the right spring strut dome in the engine compartment.
Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Serbia, Turkey) Engine oil quality Only Israel Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including CNG, LPG, E85) Diesel engines dexos 1 – – ✔ – dexos 2 ✔ ✔ – ✔ In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.
Technical data 141 International service schedule Required engine oil quality All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including CNG, LPG, E85) Diesel engines dexos 1 ✔ – – – dexos 2 – ✔ ✔ ✔ In case dexos quality is unavailable you may use the oil qualities listed below: All countries outside Europe except Israel Engine oil quality Only Belarus, Moldov
Technical data All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including CNG, LPG, E85) Diesel engines ACEA A3/B3 ✔ – ✔ – ACEA A3/B4 ✔ ✔ ✔ ✔ ACEA C3 ✔ ✔ ✔ ✔ API SM ✔ – ✔ – API SN ✔ – ✔ – Engine oil viscosity grades All countries outside Europe (except Israel), including Belarus, Moldova, Russia, Serbia, Turkey Ambient temperature Petrol and
Technical data Engine data Sales designation 1.4 Twinport CNG 1.3 CDTI 1.
Technical data Performance Engine Z 14 XEP Z 16 YNG Z 13 DTJ Z 17 DTH 164 165 1523) 170 – 1523) – Maximum speed2) [km/h] 5-speed manual transmission Manual transmission automated – Fuel consumption - CO2-emissions Tyre width up to 185 mm Engine Z 14 XEP Z 13 DTJ Z 17 DTH urban [l/100 km] 7.9 / – 6.1 / 5.9 6.6 / – extra-urban [l/100 km] 5.2 / – 4.5 / 4.5 4.4 / – total [l/100 km] 6.2 / – 5.1 / 5.0 5.
Technical data Engine Z 14 XEP Z 13 DTJ Z 17 DTH urban [l/100 km] 8.1 / – 6.3 / 6.1 6.8 / – extra-urban [l/100 km] 5.4 / – 4.7 / 4.7 4.6 / – total [l/100 km] 6.4 / – 5.3 / 5.2 5.4 / – CO2 [g/km] 153 / – 139 / 140 146 / – Manual/manual transmission automated Engine Z 16 YNG Manual transmission urban [m3/100 km] / [kg/100 km] 10.1 / 6.6 extra-urban [m3/100 km] / [kg/100 km] 5.9 / 3.9 total [m3/100 CO2 [g/km] km] / [kg/100 km] 7.5 / 4.
Technical data Vehicle weight Kerb weight Combo van Engine Manual transmission Manual transmission automated without/with air conditioning/climate control [kg] Z 14 XEP 1190 / 1350 – Z 16 YNG 1322 / 1352 – Z 13 DTJ 1285 / 1420 1285 / 1420 Z 17 DTH 1320 / 1455 – Combo Engine Manual transmission Manual transmission automated without/with air conditioning/climate control [kg] Z 14 XEP 1235 / 1265 – Z 16 YNG 1367 / 1397 – Z 13 DTJ 1325 / 1355 1325 / 1355 Z 17 DTH 1365 / 1395
Technical data Heavy accessories Folding sun Towing equipment Accessories roof Anti-lock braking system (ABS) Sliding door (front passenger´s side) Rear vent windows Load compartment grille Split load compartment grille Weight [kg] 18 7 23 9 8 10 18 Vehicle dimensions Combo van Combo Overall length [mm] 4322 4322 Overall width [mm] 1684 1684 Width with two exterior mirrors [mm] 1892 1892 Height at kerb weight [mm] 1801 Length of load compartment floor [mm] 17874) Load compartment
Technical data Combo van Combo Load compartment height [mm] 1190 1190 Load compartment sill height [mm] 550 550 Opening width, tailgate min./max. [mm] 1030 / 1210 1030 / 1210 Opening height, tailgate min./max. [mm] 1120 / 1139 1120 / 1139 Opening width of sliding door [mm] 620 620 Opening height of sliding door [mm] 913 1023 Wheelbase [mm] 2716 2716 Turning circle diameter [m] 11.25 11.25 Capacities Engine oil Engine Z 14 XEP Z 13 DTJ Z 17 DTH including Filter [l] 3.5 3.
Technical data 149 Fuel tank Engine Z 14 XEP Z 13 DTJ Z 17 DTH Petrol/diesel, nominal capacity [l] 52 52 52 Engine oil Engine Z 16 YNG including Filter [l] 3.5 Between MIN and MAX [l] 1.0 Fuel tank Engine Z 16 YNG Natural gas, nominal capacity [kg] petrol, nominal capacity [l] 17.58) 14 8) 17.5 kg (average fill limit), corresponding to a tank volume of 108 l. Fill weight in kg is dependent on outside temperature, filling pressure and type of tank system.
Technical data Tyre pressures Combo van Comfort with up to 2 people and 100 kg luggage With full load Engine front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) Z 14 XEP 175/70 R 14, 9)10) 175/65 R 14, 185/55 R 15, 11)12) 185/60 R 15 240 / 2.4 (35) 240 / 2.4 (35) 240 / 2.4 (35) 350 / 3.5 (51) Z 13 DTJ 175/70 R 14, 175/65 R 14, 185/55 R 15, 185/60 R 15 240 / 2.4 (35) 240 / 2.4 (35) 240 / 2.4 (35) 350 / 3.
Technical data 151 Combo van Comfort with up to 2 people and 100 kg luggage With full load Engine front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) Z 16 YNG 185/60 R 15, 185/55 R 15 240 / 2.4 (35) 240 / 2.4 (35) 240 / 2.4 (35) 350 / 3.5 (51) all 420 / 4.2 (61) 420 / 4.2 (61) 420 / 4.2 (61) 420 / 4.2 (61) 13) Tyres T 115/70 R 16 (Temporary spare wheel)13)3 121, 127 Notes on temporary spare wheel.
Technical data Combo Engine Tyres Comfort with up to 3 people With full load front front rear rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) Z 14 XEP 175/70 R 14,14) 175/65 R 14, 185/55 R 15, 15)16) 185/60 R 15, 17) 185/65 R 15, 195/45 R 16, 195/50 R 16 240 / 2.4 (35) 240 / 2.4 (35) 240 / 2.4 (35) 350 / 3.5 (51) Z 13 DTJ 175/70 R 14, 175/65 R 14, 185/55 R 15, 185/60 R 15, 185/65 R 15 240 / 2.4 (35) 240 / 2.4 (35) 240 / 2.4 (35) 350 / 3.
Technical data Combo Engine Tyres Comfort with up to 3 people With full load front front rear 153 rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) Z 17 DTH 185/60 R 15, 185/55 R 15, 185/65 R 15, 195/50 R 16 240 / 2.4 (35) 240 / 2.4 (35) 240 / 2.4 (35) 350 / 3.5 (51) Z 16 YNG 185/60 R 15, 185/55 R 15, 185/65 R 15 240 / 2.4 (35) 240 / 2.4 (35) 240 / 2.4 (35) 350 / 3.5 (51) T 115/70 R 16 (Temporary spare wheel) 420 / 4.2 (61) 420 / 4.2 (61) 420 / 4.
Technical data Combo Tramp / Arizona Comfort with up to 3 people With full load Engine front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 240 / 2.4 (35) 240 / 2.4 (35) 240 / 2.4 (35) 350 / 3.5 (51) Z 14 XEP Z 16 YNG Tyres 185/60 R15 185/65 R 1518) Z 13 DTJ Z 17 DTH 18) Recommended: Goodyear Eagle Hydragrip.
Technical data Towing hitch installation dimensions 155
Customer information Customer information Vehicle data recording and privacy ....................................... 156 Vehicle data recording and privacy Event data recorders The vehicle has a number of sophisticated systems that monitor and control several vehicle data. Some data may be stored during regular operation to facilitate repair of detected malfunctions, other data is stored only in a crash or near crash event by systems commonly called event data recorders (EDR).
Customer information Radio Frequency Identification (RFID) RFID technology is used in some vehicles for functions such as tyre pressure monitoring and ignition system security. It is also used in connection with conveniences such as radio remote controls for door locking/unlocking and starting, and invehicle transmitters for garage door openers. RFID technology in Opel vehicles does not use or record personal information or link with any other Opel system containing personal information.
Index A Accessories and vehicle modifications ............................ 99 Adjustable air vents ..................... 82 Airbag and belt tensioners ........... 67 Airbag system .............................. 40 Air conditioning regular operation 83 Air conditioning system ................ 81 Air intake ...................................... 82 Antilock brake system .................. 92 Antilock brake system (ABS) ....... 68 Anti-theft alarm system ................ 27 Ashtrays ....................
Engine coolant temperature gauge ....................................... 64 Engine data ............................... 143 Engine exhaust ............................ 86 Engine oil ................... 101, 135, 140 Engine oil pressure ...................... 68 Event data recorders.................. 156 Exterior care .............................. 131 Exterior lighting ............................ 13 F Fault ............................................. 91 First aid kit ...............................
Mirror adjustment ........................... 8 Misted light covers ....................... 77 R Odometer ..................................... 61 Oil, engine.......................... 135, 140 Outside temperature .................... 58 Overhead console ....................... 48 Overrun cut-off ............................. 85 Radio Frequency Identification (RFID)..................................... 157 Radio remote control ................... 19 Reading lights ..............................
Tyre pressure ............................ 119 Tyre pressures ........................... 150 Tyre repair kit ............................. 121 U Underseat storage ....................... 48 Using this manual .......................... 3 V Vehicle dimensions .................... 147 Vehicle Identification Number .... 138 Vehicle specific data ...................... 3 Vehicle storage............................. 99 Vehicle unlocking ........................... 6 Vehicle weight .......................
