OPEL Combo Owner’s Manual
OPEL Combo Operation, Safety, Maintenance
Data specific to your vehicle Please enter your vehicle’s data here to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate.
Introduction Your vehicle is an intelligent combination of forward-looking technology, impressive safety, environmental friendliness and economy. It now lies with you to drive your vehicle safely and to see it performs perfectly. This Owner’s Manual provides you with all the necessary information to that end. Make sure your passengers are aware of the possible risk of accident and injury which may result from improper use of the vehicle.
Contents In Brief ........................................................ 2 Keys, doors, windows ............................. 20 Seats, Interior .......................................... 38 Instruments ............................................. 66 Lighting ................................................... 84 Infotainment system .............................. 90 Climate control ....................................... 92 Driving and operation ......................... 100 Self-help, vehicle care ....
2 In Brief In Brief Picture no: 18079s.tif Picture no: 18080s.tif Unlocking the vehicle: Turn the key in the lock forwards or press the q button on the radio remote control 3 Unlocking the tailgate 3: Turn the key to the horizontal position or press the q button on the remote control 3 Pull on the door handle and open the door or slide open the sliding door 3. Press the button to open the tailgate. Sliding door 3 3 27.
In Brief Picture no: 18081s.tif Unlocking the leaf doors 3: Turn the key to the vertical position or press the q button on the remote control 3 To open the right leaf door, pull on the handle and pull open the door. To open the left leaf door, turn the handle on the inside. When using the remote control, the leaf doors are only unlocked if the key slot in the lock is in the vertical position. If the key slot is in the horizontal position, the leaf doors are always locked.
4 In Brief Picture no: 12429s.tif Picture no: 11536s.tif Front seat height 3: Pull lever at side To fold front seat backrest forward 3: Raise release lever Lift lever and relieve some weight from seat to raise it or press down on seat with body weight to lower it. Seats 3 38, Seat position 3 39. Never adjust the driver’s seat whilst driving. It could move in an uncontrolled manner when the lever has been pulled. Seats 3 38, Seat position 3 39. Picture no: 13781s.
In Brief Picture no: 18531s.tif Picture no: 18083s.tif 5 Picture no: 18084s.tif Pull out the seat belt and engage it in the belt buckle Adjust the exterior mirror manually using the handle Electrical exterior mirror adjustment 3 The seat belt must not be twisted and must lie snugly against the body. The backrest must not be tilted back too far (maximum approx. 25 ). Mirrors 3 34, Aspherical exterior mirrors 3 34, Folding the exterior mirrors 3 34.
6 In Brief Picture no: 18082s.tif To adjust interior mirror by swivelling Swivel lever on underside of mirror housing to reduce dazzle at night. Mirrors 3 35. Picture no: 18086s.tif Steering wheel adjustment 3: Swivel lever down, adjust height, swivel lever up, engage Adjust steering wheel only when vehicle is stationary and steering column lock is released. Airbag systems 3 3 56. Picture no: 13715s.
In Brief Picture no: 18475s.tif Headlamp flash, main beam and dipped beam Headlamp flash = Main beam Dipped beam = = Pull stalk towards steering wheel Push stalk forwards Push stalk forwards again Main beam, headlamp flash 3 85. Picture no: 14054h.tif Picture no: 15865s.tif Switch turn signal on Hazard warning lamps Right Left Operated with the ¨ button. = = Lever upwards Lever downwards Turn signals 3 85. Hazard warning flashers 3 86.
8 In Brief
In Brief 9 1 Page Light switch .......................... 3 6, 3 84 2 Side air vents ................................ 3 93 Page 10 Hazard warning lamps ................. 3 7 LED for anti-theft alarm system 33 32 3 Turn signals, headlamp flash, dipped beam, main beam .. 3 6, 3 84 11 Infotainment system 3 ................ 3 90 21 Ignition switch with steering wheel lock ...................... 3 16 12 Front passenger airbag 3 ........... 3 56 22 Steering wheel adjustment 3 ....... 3 6 4 Horn ....
10 In Brief
In Brief 1 Page Side air vents ................................ 3 93 2 Front passenger airbag 3 ........... 3 56 3 Infotainment system 3 ................ 3 90 4 Hazard warning lamps .................. 3 7 LED for anti-theft alarm system 3 .............................3 32 5 Display 3 for time, date, outside temperature, infotainment system 3 ................ 3 77 6 Centre air vents .............................3 93 7 Turn signals, headlamp flash, dipped beam, main beam .. 3 6, 3 84 8 Horn ...
12 In Brief Control indicators > Fog lamps 3, 3 66, 3 86. A Engine electronics, Immobiliser 3, Manual transmission automated 3, Fault, 3 21, 3 66, 3 116. Z Exhaust gases 3, 3 67, 3 115. v Airbag systems 3, Belt tensioners, 3 67, 3 50, 3 59. I Engine oil pressure, 3 67. p Alternator, 3 69. O Turn signal lamps, 3 68, 3 85. R C Main beam, 3 68, 3 85. Brake system, clutch system 3, 3 69, 3 179. u ! Preheating 3, diesel particle filter 3, 3 68, 3 116. Anti-lock Braking System 3, 3 119.
In Brief Picture no: 11548s.tif Operate horn: Press j right or left Airbag system 3 3 56, Remote control on steering wheel 3 3 90. Picture no: 14055h.tif Windscreen wiper: Move lever upwards & % $ § = = = = Fast Slow Adjustable interval switching Off Windscreen wiper 3 82, Adjustable wiper interval 3 3 83, Further information 3 160, 3 179. 13 Picture no: 14056h.tif Operating windscreen washer system: Lever toward steering wheel Windscreen washer system 3 82, Further information 3 180, 3 195.
14 In Brief Picture no: 14057h.tif Picture no: 11549s.tif Rear window wiper 3 and Rear window washer system 3 operation Heated rear window 3, heated exterior mirrors 3 Wiper on = Push stalk forwards Wiper off = Lever toward steering wheel Washing = Push lever forward and hold Climate control system 3 92, Heated rear window 3 37. Rear window wipers and rear window washer system 3 82, Further information 3 179, 3 180. Operated with the Ü button. Picture no: 13205s.
In Brief 15 Before starting off, check z Tyre pressure and tyre condition 3 121, 3 191, z Engine oil level and fluid levels in engine compartment 3 174 to 3 180, z All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and operational, z Seats, seat belts and mirrors are correctly adjusted 3 38, 3 48, 3 34, z Check brake function at low speed, particularly if the brakes are wet. Picture no: 15120s.
16 In Brief Picture no: 15678t.tif Picture no: 15582a.tif Steering wheel lock and ignition Starting the engine Turn key to position 1. Move the steering wheel slightly to release the steering wheel lock. Depress the clutch and brake pedals, manual transmission automated 3 in N, do not accelerate; for diesel engine, turn key to position 2; when control indicator ! goes out turn the key to position 3 and release it when the engine is running.
In Brief Parking the vehicle z Always apply handbrake firmly without operating the release button, and apply as firmly as possible on a downhill or uphill slope. z Switch off the engine and ignition by turning the ignition key to 0 and removing it. Turn the steering wheel until you can feel its lock engage (anti-theft protection). On vehicles with manual transmission automated 3, control indicator R flashes for a few seconds after the ignition is switched off if the hand brake has not been applied.
18 In Brief Picture no: 11600s.tif Airbag system The airbag system consists of several internal systems. Front airbag system 3 The front airbag system will be triggered in the event of a serious accident involving a frontal impact and forms safety cushions for the driver and front passenger. The forward movement of the driver and front passenger is checked and the risk of injuries to the upper body and head thereby substantially reduced. Picture no: 18088s.
In Brief 19 Diesel particle filter 3 The diesel particle filter system filters harmful soot particles out of the exhaust gases. The system includes a self-cleaning function that run automatically during driving. The filter is cleaned by burning off the soot particles at high temperature. This process takes place automatically under set driving conditions and may take up to 25 minutes. Fuel consumption may be higher during this period. The emission of smells and smoke during this process is normal.
20 Keys, doors, windows Keys, doors, windows Replacement keys The key number is specified in the Car Pass 3. The key is part of the electronic immobiliser. Locks 3 22, 3 162. Replacement keys ............................... Key with retractable key blade 3 ...... Car Pass................................................ Electronic immobiliser.......................... Mechanical unlocking or locking of individual doors................................. Remote control 3.................................
Keys, doors, windows 21 If control indicator A lights up after the engine has started, there is a fault in the engine electronics or the manual transmission automated 3 104. Note The immobiliser does not lock the doors. You should always lock the vehicle after leaving it and switch on the anti-theft alarm system 3, 3 22, 3 24, 3 31. Picture no: 15761t.tif Electronic immobiliser The system checks whether the vehicle is allowed to start with the key used.
22 Keys, doors, windows Picture no: 18115s.tif Mechanical unlocking or locking of individual doors (versions without remote control 3 and central locking system 3) Front doors and sliding doors 3 To unlock Turn key in lock towards front of vehicle as far as it will go. Return key to the vertical position and remove. Pull door handle. To lock With door or sliding door closed, turn key towards rear of vehicle as far as it will go. Turn key back to vertical position and remove.
Keys, doors, windows 23 Fault If the central locking system cannot be operated with the remote control, it may be due to the following: z Range exceeded. z Battery voltage of the radio remote control too low, change battery. z Frequent, repeated operation of the remote control outside the reception range of the vehicle (e.g. too far from vehicle, remote control is then no longer recognised). Synchronise the remote control. Picture no: 15330t.tif Remote control 3 Picture no: 15331t.
24 Keys, doors, windows Key with fixed key section Have the battery changed in a workshop. Radio remote control synchronisation After changing the battery, unlock the door with the key in the lock 3 26. Inserting the key in the ignition synchronises the remote control. Picture no: 15332t.tif Remote control battery replacement Replace the battery as soon as the range of the remote control begins to shrink. Batteries do not belong in household waste.
Keys, doors, windows 25 Note z To prevent the driver from being inadvertently locked out, the button on the driver’s door cannot be depressed when the door is open. z If the driver’s door is not closed properly, the central locking system will unlock again immediately after locking. z A short time after unlocking with the remote control, the doors lock again automatically if no door is opened. Picture no: 15333t.tif Picture no: 15334t.
26 Keys, doors, windows Malfunction in central locking system Fault If the central locking system cannot be operated, the problem may be as follows: To unlock Turn the key in the driver’s door lock towards the front of vehicle, turn it back to the vertical position and remove. The driver’s door is unlocked. The other doors can be opened by pulling the lock button (unless the anti-theft locking system 3 is active). The luggage compartment and tank flap remain locked.
Keys, doors, windows Picture no: 18098s.tif Sliding doors 3 9 Warning If the vehicle is parked facing down a slope, open sliding doors may move accidentally on account of their weight. Close the sliding doors before driving off. Opening from outside Unlock the door with the key by turning it forwards in the lock or pressing the q button on the remote control. To open the sliding doors, pull the handle and slide the door towards the rear of the vehicle. Picture no: 18092s.
28 Keys, doors, windows Picture no: 18116s.tif Tailgate 3 To open Turn the key in the lock to the vertical position or press the q button on the remote control. Press the button to open the tailgate. To close Close the tailgate and turn the key in the lock to a horizontal position or press the p button on the remote control. Picture no: 18118s.tif Central locking 3 and the tailgate The central locking system and anti-theft locking system 3 for the doors cannot be operated via the tailgate lock.
Keys, doors, windows Picture no: 18117s.tif Leaf doors 3 To open Turn the key in the lock to the vertical position or press the q button on the remote control. Open right-hand leaf door from outside by raising door handle or from inside by pivoting handle. Picture no: 18096s.tif Unlock and open the left-hand leaf door from inside by pivoting the handle. The doors engage at a 90 position.
30 Keys, doors, windows Notes on tailgate or leaf doors z After fitting certain accessories, it might not be possible to keep the tailgate in the open position. z The number plate can only be seen when the tailgate or rear doors are closed. Do not drive with an open tailgate or open leaf doors. 9 Warning Picture no: 18119s.tif Central locking 3 and the leaf doors The central locking system and anti-theft locking system 3 for the doors cannot be operated via the leaf door lock.
Keys, doors, windows 31 Anti-theft alarm system 3 monitors z the doors, luggage compartment, bonnet, z the passenger compartment, z vehicle tilt, e. g. if it is raised, z the ignition. 9 Warning Do not activate the system if there are people in the vehicle! The doors cannot be unlocked from inside. Picture no: 15334t.tif Picture no: 11575s.tif To activate All doors, windows and the bonnet must be closed. Press the p button on the remote control again within 10 seconds of locking.
32 Keys, doors, windows After the first 10 seconds of anti-theft alarm system activation: z LED flashes slowly z LED illuminates for approx. 1 second = System switched on, = Switch-off function. Contact a workshop for assistance if problems are encountered. Picture no: 15987s.tif Light emitting diode (LED) During the first 10 seconds of anti-theft alarm system activation: z LED comes on = z LED flashes rapidly = Test, delayed switch-on, Door, luggage compartment or bonnet open or system fault.
Keys, doors, windows 33 Note z Modifications to the passenger compartment, such as fitting seat covers, could hinder the function of passenger compartment monitoring. z Switch off passenger compartment monitoring of the interior of the parked vehicle is being heated. Picture no: 18094s.tif Opening and closing the luggage compartment 3 when the anti-theft alarm system is enabled 1. To unlock: Tailgate: Turn key clockwise all the way past the horizontal position.
34 Keys, doors, windows Picture no: 18083s.tif Exterior mirrors Adjust manually using handles in the front doors or electrically 3 using switches in the driver’s door console. Manual exterior mirror adjustment Adjust the exterior mirror using the handle. Picture no: 18084s.tif Picture no: 18085s.tif Electrical exterior mirror adjustment 3 Select the corresponding exterior mirror with the rocker switch and adjust with the four-way switch.
Keys, doors, windows Picture no: 11549s.tif Heated exterior mirrors 3 Heating is activated or deactivated by pressing the Ü button. Heating is operable when the ignition is switched on. Picture no: 18082s.tif Interior mirror 35 Picture no: 18104s.tif Swivel mirror housing to adjust. Manual window operation, front doors To reduce dazzle, swivel the lever on the underside of the mirror housing. The door windows can be operated using window winders.
36 Keys, doors, windows Electric windows 3 9 Warning Exercise care when operating electric windows. Risk of injury, especially for children. Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move. Operational readiness Operational when the ignition key is in position 1 in the ignition switch. Picture no: 18105s.tif Window in the sliding doors 3 z To open = z To close = Release joint and push outwards. Pull joint and engage.
Keys, doors, windows 37 Fault If the windows cannot be opened and closed automatically, activate the window electronics as follows: 1. Close doors. 2. Switch on ignition. 3. Close the window completely and hold the rocker switch depressed for at least another 5 seconds. 4. Open the window completely and hold the rocker switch depressed for at least another 1 second. Picture no: 17899s.tif 5. Repeat for each window. Picture no: 11549s.
38 Seats, Interior Seats, Interior Front seats ........................................... Head restraints .................................... Luggage compartment extension ..... Lashing eyes 3 .................................... Luggage compartment cover 3......... Safety net 3 ......................................... Load compartment grille 3 ................ Notes on loading the vehicle.............. Three-stage safety system.................. Three-point seat belts .........................
Seats, Interior Picture no: 12429s.tif Adjust height of seat Lift lever and relieve some weight from seat to raise it or press down on seat with body weight to lower it. Picture no: 11536s.tif Tilting the backrests forward In order to fold the backrest forwards, lift the release lever. 39 Picture no: 18530s.tif Seat position 9 Warning Only drive with the seat correctly adjusted. z Sit with your buttocks as far back against the backrest as possible.
40 Seats, Interior z Sit with your shoulders as far back against the backrest as possible. Set the backrest rake so that you can easily reach the steering wheel with your arms slightly bent. Maintain contact between your shoulders and the backrest when turning the steering wheel. Do not angle the backrest too far back. We recommend a maximum rake of approx. 25 . z Adjust the steering wheel 3 6. z Set seat height 3 high enough to have a clear field of vision on all sides and of all display instruments.
Seats, Interior Picture no: 12435s.tif Picture no: 13783s.tif 41 Picture no: 11581s.tif Adjusting the centre rear head restraint 3 To improve visibility when the centre rear seat is not occupied or to fold the backrest, press the detent springs on the guide sleeves to release the head restraint and push it all the way down. Head restraint position Only drive with the head restraint set to the proper position. The rear, centre head restraint 3 cannot be removed.
42 Seats, Interior Luggage compartment extension Remove the luggage compartment cover 3 if necessary 3 44. Pull out the push-in collars 3 for the ISOFIX child-restraint system mounting. Closely follow the installation instructions accompanying the ISOFIX child restraint system. Picture no: 18099s.tif Folding down the rear seat backrests Push the rear, outer head restraint 3 down completely or remove it 3 40. Push the rear, centre head restraint 3 down completely 3 41.
Seats, Interior 43 Repositioning the rear seats Pull the seat belt slightly forward so that it does not get damaged and audibly engage the backrests. Reposition the seat cushions. Insert outer rear head restraints 3. Picture no: 12438s.tif To fold one or both of the rear seat backrests, press the button at the top to release the backrest (Fig. 18099 S) and fold it forward. Picture no: 13787s.tif Folding down the front passenger seat 3 Push the passenger seat head restraint down or remove it 3 40.
44 Seats, Interior Picture no: 18101s.tif Picture no: 12447s.tif Lashing eyes 3 Luggage compartment cover 3 The four lashing eyes in the luggage compartment that are shown in the illustration are used to secure objects that are being transported so that they do not slide around. Do not place any heavy or sharp-edged objects on the cover. The brackets on the floor between the front seats are only used to secure the safety net 3 3 45. They must not be used as lashing eyes.
Seats, Interior Picture no: 12443s.tif Picture no: 12444s.tif Safety net 3 Fold down both rear seat backrests. Passengers must not be carried behind the safety net. Hook tensioning straps into lashing eyes in floor and tighten by pulling on the loose end of the strap. The safety net can be fitted behind the rear seats or, with the rear seat backrest folded down, behind the front seats. Remove the luggage compartment cover as necessary 3 44. Unroll the safety net.
46 Seats, Interior Picture no: 16125s.tif Load compartment grille 3 To prevent vehicle occupants from being injuried by loose cargo, a load compartment grille can be installed behind the front seats. Split load compartment grille 3 To enlarge the load compartment, the grille can be moved forwards on the front passenger’s side. Push the head restraint of the front passenger seat down as far as it will go 3 40.
Seats, Interior z If the seat backrests are not folded down when transporting objects in the luggage compartment, the backrests must be fully upright and engaged in position 3 42. z The EC kerb weight includes allowances for the driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full). z Do not allow the load to protrude above the upper edge of the backrests. z Weights and payload 3 189. z The warning triangle 3 and first-aid kit (cushion) 3 must always be freely accessible.
48 Seats, Interior Three-stage safety system Comprising: z three-point seat belts, z belt tensioners at the front seats, z airbag systems for driver and front passenger 3. The three stages are activated in sequence depending on the severity of the accident: z The automatic seat belt locking devices prevent the belt strap from being pulled out and thus ensure that the vehicle occupants are retained in their seats. z The seat belts of the front seats are pulled downwards at the belt buckles.
Seats, Interior 9 Warning Fasten your seat belt before each trip. In the event of an accident, persons not wearing seat belts endanger their fellow occupants and themselves. Seat belts are only designed for use by one person at a time. They are not suitable for persons younger than 12 years of age or smaller than 150 cm. For children up to 12 years of age, we recommend the Opel child restraint system 3 53.
50 Seats, Interior Belt tensioners In the event of a head-on or rear-end collision of a certain severity, the front seat belts are pulled down at the buckles and thereby tightened. Picture no: 11594s.tif Actuation of belt tensioners is indicated by illumination of control indicator v; see next column. Triggered belt tensioners must be replaced by a workshop. Belt tensioners can only be triggered once. Picture no: 11702s.
Seats, Interior 9 Warning Have cause of fault remedied immediately by a workshop. The system’s integrated self-diagnostics allows faults to be quickly remedied. Important z Do not affix or place accessories or other objects within the deployment zone of the belt tensioners (in the area of the belt buckle). Do not make any modifications to belt tensioner components and the inertia real device because this will invalidate the vehicle type approval. 9 Warning Incorrect handling (e.g.
52 Seats, Interior Picture no: 11595s.tif Operation of the seat belts Fitting seat belts The seat belt must not be twisted and must lie snugly against the body. The backrest must not be tilted back too far (maximum approx. 25 ). Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Pull the belt out of the reel, guide it across the body (making certain it is not twisted) and engage the latch plate in the buckle.
Seats, Interior Child restraint system 3 Follow the usage instructions for the child restraint system. Always comply with local or national regulations. In some countries, the use of child restraint systems is forbidden on certain seats. 53 Selecting the right system Your child should be transported facing the rear in the vehicle for as long as possible.
54 Seats, Interior Permissible options for fitting a child safety seat Weight and age class1) Group 0: up to 10 kg or approx. 10 months On front passenger seat On an outboard seat in the rear row of seats On middle seat2) in the rear row of seats Group II: 15 to 25 kg or approx. 3 to 7 years X U+ U X U+ U X U U Group III: 22 to 36 kg or approx. 6 to 12 years 1) 2) U = universally suitable in conjunction with three-point seat belt. + Group 0+: up to 13 kg or approx.
Seats, Interior 55 Note z Children under 12 years of age or 150 cm must only travel in an appropriate child restraint system on the seats in the rear row 3. z The covers of the Opel child restraint system can be wiped clean. Mounting clips 3 for ISOFIX child restraint systems z When transporting children, use the child restraint systems suitable for the child’s weight. z Do not stick anything on the child restraint systems and do not cover them with any other materials.
56 Seats, Interior Examples of events triggering the front airbag system: z Impact against a non-yielding obstacle: the front airbags are triggered at low vehicle speed. z Impact against a yielding obstacle: (such as another vehicle): the front airbags are only triggered at a higher vehicle speed. Picture no: 16424s.tif Picture no: 11734s.
Seats, Interior Picture no: 11600s.tif When triggered, the front airbags inflate in milliseconds to form a safety cushion for the driver and front passenger. The forward movement of the front seat occupants is checked, thereby substantially reducing the risk of injury to the upper body and head. No impairment of view will occur, because the airbags inflate and deflate so quickly that it is often not even noticed in an accident. Picture no: 18530s.
58 Seats, Interior Picture no: 11601s.tif Side airbag 3 The side airbag system consists of an airbag in each front seat backrest. This can be identified by the word AIRBAG. The side airbag system comprises: z an airbag with inflator in the back of the driver’s and front passenger seat respectively, z the control electronics, z the side impact sensors, z the control indicator for airbag systems v in the instrument. Picture no: 13195s.
Seats, Interior 9 Warning 9 Warning Keep the area in which the airbag inflates clear of obstructions. Have cause of fault remedied immediately by a workshop. The side airbags will not be triggered in the event of The system’s integrated self-diagnostics allows faults to be quickly remedied. z the ignition is switched off, z frontal collisions, z accidents in which the vehicle overturns, z collisions involving a rear impact, z collisions involving a side impact outside the passenger cell.
60 Seats, Interior Important z No objects or accessories must be placed in the area in which the airbags inflate, as they could cause injury when the components are deployed. z Do not place any objects between the airbag systems and the vehicle occupants. Danger of injury. Do not install a child restraint system 3 on the front passenger seat. Danger to life. 9 Warning As with any other object, child restaint systems must not be carried on a passenger’s lap. Danger to life.
Seats, Interior 61 Use of child restraint systems 3 9 Warning No child restraint system 3 may be installed on front passenger seat. Danger to life. Child restraint systems must only be installed on the seats of the rear row 3. On versions without rear row of seats, no child restraint system may be installed on the front passenger seat. Picture no: 15888s.tif Picture no: 13738s.tif Cigarette lighter 3 Accessory socket 3 The cigarette lighter is in the centre console.
62 Seats, Interior Do not exceed the maximum power consumption of 120 watts. Electrical accessories connected to the socket must comply with the electromagnetic compatibility requirements laid down in DIN VDE 40 839, otherwise vehicle malfunctions may occur. Do not connect any current-delivering accessories, e.g. electrical charging devices or batteries. Picture no: 11589s.tif Ashtray 3 Caution To be used only for ash and not for combustible rubbish.
Seats, Interior Picture no: 11591s.tif Rear ashtray 3 In the rear centre console. Picture no: 11592s.tif Stowage compartments To open, swivel the cover upwards. Glove compartment To open, pull handle. To empty, lift the cover and pull the ashtray out upwards by its cover. On the inside of the glove compartment cover there is a pen holder. In vehicles with Infotainment system 3, the telematics unit 3 can be housed in the glove compartment. The glove compartment should remain closed while driving.
64 Seats, Interior Extendable stowage trays 3 The extendable stowage trays are located in the front seat backrests. To unfold, pull upwards until it engages. To fold away, press downwards past the resistance. Do not play heavy objects on the tray. Picture no: 11699s.tif Stowage compartment 3 beneath passenger seat Lift stowage compartment by grasping the recessed edge and pull it out. Maximum load: 1 kg. To close the stowage compartment, push it in and engage. Picture no: 18102s.
Seats, Interior Picture no: 16059s.tif Coin holder 3 In the centre console. Sun visors Use the sun visor to protect from glare by pulling it down and swivelling it to the side.
66 Instruments Instruments Picture no: 18529s.tif Control indicators ................................ Instrument display ............................... Information display ............................. Warning buzzers.................................. Windscreen wipers............................... 66 71 76 82 82 Control indicators The control indicators described here are not present in all vehicles. The description applies to all instrument versions.
Instruments 67 I Engine oil pressure Control indicator lights up red It illuminates when the ignition is switched on and goes out shortly after the engine starts. Illuminates when the engine is running Caution Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels. Picture no: 18529s.tif Flashes when the ignition is on Fault in the electronic immobiliser system; the engine cannot be started 3 21.
68 Instruments O Turn signal lamps Control indicator flashes green. The control indicator flashes if a turn signal or the hazard warning flashers are activated. Rapid flashing: lamp or associated fuse has failed. Replacing bulbs 3 151. Fuses 3 145. C Main beam Control indicator lights up blue. It is illuminated when main beam is on and during headlamp flash 3 85. ! Picture no: 18529s.
Instruments 69 r R u Illuminates when the fog tail lamp is on 3 86. Illuminated Illuminates when the ignition is switched on if the hand brake is applied 3 120. Illuminates while driving Fault in the anti-lock braking system 3 119. Fog tail lamp Control indicator lights up yellow. p Alternator Control indicator lights up red It illuminates when the ignition is switched on and goes out shortly after the engine starts. Illuminates when the engine is running Stop and turn engine off.
70 Instruments Y Fuel level 3 Control indicator lights up and/or flashes yellow Lamps Level in fuel tank too low. Flashes Fuel level is used up, fuel immediately. Never let the tank run dry! Erratic fuel supply can cause the catalytic converter to overheat 3 114. S Picture no: 18529s.tif Engine oil level 3 Control indicator lights up yellow. The engine oil level is checked automatically. Illuminates when the engine is running Engine oil level too low.
Instruments 71 Vehicles with clock in odometer To reset, press button with ignition switched on and trip odometer activated and hold down for approximately 2 seconds. To switch between trip odometer and clock display 3 give reset knob a brief press – see next page. Bottom line: Odometer Records the number of kilometres Service interval display 3 173. Picture no: 12098s.tif. Instrument display Tachometer Displays the engine rpm. Drive in a low engine speed range for each gear as much as possible.
72 Instruments Setting the time On the clock display, press the setting knob on the instrument for approx. 2 seconds. The flashing value is set by pressing briefly. Press for about 2 seconds again to switch to the next setting and at the end to exit setting mode. Picture no: 12099s.tif. Time display in odometer 3 To switch between trip odometer and time display 3 give reset knob a short press.
Instruments 73 For physical reasons, the engine temperature gauge shows the coolant temperature only if the coolant level is adequate. During operation the system is pressurised. The temperature may therefore rise briefly to over 100 C. Picture no: 11688s.tif Coolant temperature display Coolant temperature gauge.
74 Instruments Display: Petrol operation: 1/1 - Tank pressure approx. 200 bar Display: 3/4 - Tank pressure approx. 150 bar 1/1 - Tank content approx. 14 litres 1/2 - Tank pressure approx. 100 bar When the petrol level is getting low, the engine may sputter when taking curves. Refuel immediately if control indicator Y begins to flash! 1/4 - Tank pressure approx. 50 bar In order to achieve the maximum range in natural gas operation, we recommend that you make use of the entire reserve area.
Instruments Picture no: 12478s.tif Transmission display 3 Display of current gear or mode with manual transmission automated 3. R N A 1-5 Reverse gear Neutral Automatic mode for manual transmission automated Manual mode, current gear with manual transmission automated Manual transmission automated 3 3 100. Picture no: 14419s.tif Service display 3 If it illuminates in the odometer display, book vehicle into a workshop as soon as possible for a service with maintenance.
76 Instruments FM AS 12:01 17 ,0°C FM 3 90,6 MHz REG AS RDS [TP] REG CDin MP3 8:56 -5 ,5°C 07.04.2004 90.6 MHz TP 19,5° Picture no: 17913s.tif Information display Triple information display 3 Display of time, outside temperature and date/infotainment system (when it is on). When the ignition is off, the time, date and outside temperature can be displayed by briefly pressing one of the two buttons adjacent to the display. : 19:36 Picture no: 16711t.
Instruments 77 Automatic time synchronisation 3 The RDS signal of most VHF transmitters automatically sets the time. This can be identified by } in the display. Slippery road -2,5°C 8:56 5 ,5°C 07.04.2004 OK Picture no: 16707t.tif In vehicles with graphical information display 3, Slippery road is shown in the display as a warning for icy road surfaces. There is no message below -5 C. 9 Warning Caution: The road surface may already be icy even though the display indicates a few degrees above 0 C.
78 Instruments FM AS [TP] REG CDin MP3 90.6 MHz 19,5° 19:36 Picture no: 16711t.tif Graphical information display 3, selecting functions The graphical information display depicts functions and their menus. Functions are selected and executed in the menu on the display using the four-way button, the multifunction button 3 on the infotainment system or the buttons 3 on the steering wheel. Picture no: 15593t.
Instruments 7 FM AS [TP] REG CDin MP3 Settings Time, Date 79 19,5° 19:36 19:36 Language 90.6 MHz Units 10 . 07 . 2004 Contrast Day / Night 19,5° Picture no: 14034s.tif To select with steering wheel buttons 3 Select menu options via the menus using the buttons. 19:36 Picture no: 16711t.tif Function ranges Each function has a main page, which is selected from the upper row of the display (not in Infotainment system CD 30): z Audio, z Navigation 3, z Telephone 3.
80 Instruments 7 Automatic time synchronisation 3 The RDS signal of most VHF transmitters automatically sets the time. Time, Date Time Date 19,5° 19:36 19:36 10 . 07 . 2004 6 Synchron. clock automatical. Picture no: 16713t.tif Some transmitters do not send a correct time signal. In such cases, we recommend that you switch off automatic time synchronisation. On infotainment systems with navigation 3, time and date are also harmonised upon receipt of a GPS satellite signal.
Instruments 7 13 Languages 19,5° 19:36 X Deutsch 7 Settings 19,5° 19:36 Language ~ Europe-SI Español Units Japan Nederlands Contrast | | | Français Day / Night Italiano 6 Ign. logic Picture no: 16715t.tif Selections are indicated by a 6 in front of the menu item. In systems with language version 3, when the language setting of the display is changed, the system will ask if the message language should also be changed - see infotainment system instructions.
82 Instruments Setting display mode 3 Display brightness is independent of vehicle lighting. Settings are made as follows: Select menu item Day / Night from the Settings menu. The options are displayed. Automatic: Adapted based on vehicle lighting. Always day design: Black text on light background. Always night design: White text on dark background. Selections are indicated by a o in front of the menu item. Ignition logic 3 Setting, see infotainment system instructions.
Instruments 83 Adjustable wiper interval To set the wiper interval to a value between 2 and 15 seconds: Lever to interval operation $, lever to §, wait for required interval delay, Level to interval operation again $. The selected interval will remain stored until the next time it is changed or until the ignition is switched off. After switching on the ignition and moving the lever up, $ the interval is set to 7 seconds. Picture no: 14056h.
84 Lighting Lighting Versions with daytime running lights 3 If the light switch is set to 7, dipped beam is activated without instrument illumination when the ignition is switched on. The daytime running lights switched off when the ignition is switched off. Exterior lights ....................................... Main beam, headlamp flash .............. Turn signal lamps ................................ Reversing lamps................................... Fog lamps > 3....................................
Lighting 85 Reversing lamps The reversing lamps come on when the ignition is on and reverse gear is engaged. Picture no: 18475s.tif Picture no: 14054h.tif Main beam, headlamp flash Turn signal lamps Push stalk forward to switch from dipped beam to main beam. Lever upwards Lever downwards To switch to dipped beam, push lever down again. If the stalk is moved past the resistance point, the turn signal lamp remains on.
86 Lighting Fog tail lamp r The fog tail lamp can only be switched on if both the ignition and dipped beam/ parking lamps are on. Operated with the r button. The fog tail lamp of the vehicle is deactivated when towing a caravan/ trailer. Picture no: 13720s.tif Picture no: 15865s.tif Fog lamps > 3 Hazard warning lamps The fog lamps can only be switched on if both the ignition and lights are on. Operated with the ¨ button. Operated with the > button.
Lighting 87 Combo 0 1 2 = = = 3 = Front seats occupied All seats occupied All seats occupied and luggage compartment load Driver’s seat occupied and luggage compartment load Combo van Picture no: 13719s.tif Headlamp range adjustment ? 3 Rotate the adjuster wheel to the required position to adjust the dipped beam range to vehicle loading and prevent dazzling.
88 Lighting Luggage compartment and loading area lighting 3 The luggage compartment lighting comes on when the luggage compartment is opened. Automatically regulated centre console lighting 3 Spotlight in housing of interior mirror. Daylight-dependent, automatically regulated centre console lighting with ignition switched on. Picture no: 13721s.tif Courtesy lamp 0 Automatic interior light Comes on automatically when the vehicle is unlocked with the remote control or when a door is opened.
Lighting Battery discharge protection 3 Headlamps when driving abroad Some consumers such as the interior lighting switch themselves off after approx. 30 minutes if the ignition is off in order to protect the battery charge. The asymmetrical dipped beam increases the field of vision on the passenger side of the lane. Misted light covers The inside of the lamp bezels may mist briefly when subjected to adverse wet and cold winter conditions, strong rain or after the vehicle is washed.
90 Infotainment system Infotainment system Radio reception 3 Radio reception may be disrupted by static, noise, distortion or loss of reception due to z Changes in distance from the transmitter, z multi-path reception due to reflection and z shadowing. Infotainment system 3 The infotainment system is operated as described in the operating instructions. Radio reception 3................................ Infotainment system 3........................ Steering wheel remote control 3........ AUX input 3......
Infotainment system Mobile telephones and radio equipment (CB) 3 The Opel installation instructions and the operating guidelines provided by the telephone manufacturer must be observed when fitting and operating a mobile telephone. Failure to do so could invalidate the vehicle’s operating permit (EU Directive 95/54/EC). Recommended prerequisites for fault-free operation: z Professionally installed exterior antenna to obtain the maximum range possible Picture no: 18472s.
92 Climate control Climate control Heating, ventilation and air conditioning system 3 ...................... Air vents ............................................... Heating and ventilation system ......... Air conditioning system 3................... Air intake .............................................. Air outlet............................................... Pollen filter ........................................... Regular operation ............................... Service ........................
Climate control 93 Additional vents Located in front of the windscreen, in front of the door mirrors and in the front foot wells. Picture no: 15928s.tif Air vents At least one air vent must be open while cooling 3 (air conditioning compressor) is on in order to prevent the evaporator from icing up due to lack of air movement. Comfortable ventilation of the interior is based on the position of the temperature switch.
94 Climate control Picture no: 11612s.tif Heating and ventilation system Temperature Adjusted using left-hand rotary switch. Red area Blue area = = warm cold The amount of heat is dependent on the coolant temperature and is thus not fully attained until the engine is warm. Picture no: 11613s.tif Picture no: 11614s.tif Air flow Adjusted using centre rotary switch. Air distribution Adjusted using right-hand rotary switch.
Climate control 95 Heating For rapid warming of the passenger compartment: z Turn the temperature switch clockwise as far as it will go (warm). z Set the fan to speed 3. z Set the air distribution switch to the desired position, preferably position J 3 94. The comfort and general well-being of the vehicle occupants are to a large extent dependent on a suitable ventilation and heating setting. Picture no: 11618s.tif Ventilation z Set the temperature to the desired setting.
96 Climate control z Turn the temperature switch clockwise as far as it will go (warm). z Set fan to 3 or 4. z Set air distribution switch to V. z Activate heated rear window Ü. z Open side air vents as required and direct them towards side windows. z For simultaneous warming of the foot well, set air distribution switch to J. Picture no: 16489s.
Climate control 97 9 Warning The air recirculation system minimises the entry of outside air. The humidity increases, and the windows can mist up. The quality of the passenger compartment air deteriorates which may cause vehicle occupants to feel drowsy. Air distribution to V: the air recirculation system is automatically switched off to speed up window demisting and prevent fogging. Picture no: 13203s.tif Picture no: 13202s.tif Cooling n Only operate with the engine and fan running.
98 Climate control Picture no: 11624s.tif Comfort setting z Set cooling n as desired. z Air recirculation system 4 off. z Set temperature switch as desired. z Switch on fan at desired speed. z Set air distribution switch to M or L. z Open vents as required. Temperature switch in centre of adjustment range: warmer air will flow into the foot well and cooler air into the upper zone, with warmer air coming from the side air vents and cooler air from the centre vents. Picture no: 11622s.
Climate control Regular operation z Cooling n on, the air conditioning compressor automatically switches off in low outdoor temperatures (ice formation), To make sure that the AC compressor is constantly working well, the cooling system 3 must be switched on several minutes once a month regardless of the weather or season. It is not possible to activate cooling when outside temperatures are low. z Turn the temperature switch clockwise. z Set fan to 3 or 4.
100 Driving and operation Driving and operation Manual transmission automated 3 The Easytronic transmission permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control. Manual transmission automated 3 ... Manual transmission ........................... Driving hints ......................................... Saving Fuel, Protecting the Environment ...................................... Fuels, refuelling....................................
Driving and operation 101 Starting the engine Briefly operate foot brake when starting the engine. The engine can now be started in position N and with the foot brake operated. N appears in the gear display. If the foot brake is not operated, "N" flashes in the gear display and the engine cannot be started.
102 Driving and operation Selector lever in + or Shift to a higher gear. Shift to a lower gear. + - If a higher gear is selected when the running speed is too low, or a lower gear when the speed is too high, no shift is carried out. This prevents the engine from running at too low or too high revs. Picture no: 12466s.tif Selector lever in A/M Switch between Automatic and Manual mode. In manual mode, a gear can be selected manually by tapping the selector lever to the + or - position.
Driving and operation 103 Engine braking Automatic mode When driving downhill, the manual transmission automated does not shift into higher gears until a fairly high engine speed has been reached. When braking, the transmission shifts down in good time. Manual mode To utilise the engine braking effect, select a lower gear in good time when driving downhill. Picture no: 12479S.
104 Driving and operation Vehicle storage Apply the handbrake and remove the key from the ignition. The previously selected gear (shown on the transmission display) remains selected. No gear is selected in selector lever position N. When the ignition is switched off, the manual transmission automated no longer responds to movement of the selector lever. Picture no: 14083j.
Driving and operation 105 3. Clean the transmission around the cap (see figure) so that no dirt can get into the opening when the cap is removed. 4. Rotate cap to slacken and remove by lifting upwards – see figure. 5. Turn the adjusting screw clockwise using a flat-head screwdriver (vehicle tools 3 3 136) until clear resistance can be felt. The clutch has now been disengaged. Caution Picture no: 13739s.
106 Driving and operation Driving hints The first 1000 km Drive your vehicle at various speeds. Do not use full throttle. Never allow the engine to labour at low revs. Change gear frequently. Do not press the accelerator pedal more than approx. 3/4 in all gears. Do not drive faster than three quarters of maximum speed. Do not brake unnecessarily hard for the first 200 km. During the first drive, smoke may develop because of wax and oil evaporating off the exhaust system.
Driving and operation Save energy – more kilometres Please observe the running-in hints on the previous page and the tips for saving energy on the following pages. Good, technically correct and economical driving ensures maximum durability and performance for your vehicle. Overrun cut-off The fuel supply is automatically cut off during overrun, e.g. when the vehicle is driven with a gear engaged but no throttle application. Overrun cut-off is deactivated if catalytic converter temperature is high.
108 Driving and operation Saving Fuel, Protecting the Environment Trend-setting technology Environmentally friendly and mainly recyclable materials were used when your vehicle was being developed and manufactured. The production methods used to make your vehicle are also environmentally-compatible. Recycling of production wastes keeps the circulation of material closed. Reduction of energy and water requirements also helps to conserve natural resources.
Driving and operation Overrun z The fuel supply is automatically shut off during overrun, e.g. when the vehicle is being driven down long gradients or when braking 3 107. z To enable the overrun cut-off to come into action and save fuel, do not accelerate or declutch during overrun. Correct gear selection z High revs increase engine wear and fuel consumption. z Do not race your engine. Avoid driving at high engine speeds. Making use of the tachometer helps to save fuel.
110 Driving and operation Fuels, refuelling Fuel consumption Fuel consumption is determined under specific driving conditions 3 186. Special equipment increases the weight of the vehicle. As a result, they can increase fuel consumption and reduce the specified maximum speed. There is increased friction between engine and transmission parts during the first 1000 kilometres. This increases fuel consumption. Fuel for petrol engines Only use unleaded fuel that complies with DIN EN 228.
Driving and operation 111 9 Warning Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this rectified immediately by a workshop. Fuel filler neck at right rear side of vehicle. Picture no: 15829t.tif Fuel filler cap Only a Opel Genuine fuel filler cap provides full functionality. Diesel-engined vehicles have special fuel filler caps.
112 Driving and operation Correct filling depends to a large extent on proper operation of the fuel dispensing pump: 1. Fully insert the pump nozzle and switch it on. 2. After the automatic cut-off, the nominal capacity of the fuel tank can be obtained by topping up with two doses of fuel. Make sure the nozzle is fully inserted. To close, place fuel filler cap in position and turn, overcoming the resistance until the ratchet on the cap engages audibly. Lock the fuel filler cap with the ignition key 3.
Driving and operation 113 Refuelling when driving abroad When refuelling in another country, please note that country-specific expressions are used for natural gas vehicles. German Erdgasfahrzeuge Erdgas als Kraftstoff English NGVs = Natural Gas Vehicles CNG = Compressed Natural Gas French Véhicules au gaz naturel – or – Véhicules GNV GNV = Gaz Naturel (pour) Véhicules – or – CGN = carburant gaz naturel Italian Metano auto Metano (per auto) Picture no: 16882s.
114 Driving and operation If the natural gas tank is then not refilled, petrol operation must be manually selected the next time the engine is started. This is necessary in order to prevent damage to the catalytic converter (overheating due to irregular fuel supply). If the switch is pressed several times within a brief period of time, a changeover inhibitor is activated. The engine continues with the current type of fuel. The inhibitor remains active until the ignition is switched off.
Driving and operation 115 z In the event of misfiring, uneven engine running, a clear reduction in engine performance or other unusual problems, have the cause of the fault rectified by a workshop as soon as possible. In an emergency, driving can be continued for a short period, keeping vehicle speed and engine speed low. z If unburnt fuel enters the catalytic converter of a petrol engine, this may result in overheating and irreparable damage to the catalytic converter.
116 Driving and operation If it illuminates briefly, but does not recur, it is of no significance. If A illuminates, there may be water in the diesel fuel filter 3. Have the fuel filter checked for water residue by a workshop 3 177. If it flashes after the ignition is switched on, there is a fault in the immobiliser system. The engine cannot be started 3 21. Engine exhaust 9 Warning Picture no: 11718s.
Driving and operation Picture no: 18528s.tif Under certain driving conditions, e.g. short distances, the system cannot clean itself automatically. If the filter requires cleaning and previous driving conditions did not enable automatic cleaning, control indicator ! flashes. Continue driving, keeping engine speed above 2000 rpm-1. Shift down if necessary. Diesel particle filter cleaning is then initiated. Picture no: 18535s.
118 Driving and operation Maintenance Have all maintenance work carried out at the specified intervals. We recommend that you entrust this work to your Opel Partner, who has proper equipment and trained personnel available. Electronic testing systems permit rapid diagnosis and remedy of faults.
Driving and operation 119 For vehicles with manual transmission automated 3, the control indicator flashes for a few seconds when the ignition is turned off if the hand brake is not applied. Anti-lock Braking System (ABS u) 3 ABS prevents the wheels from locking. ABS starts to regulate brake pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even during hard braking. Picture no: 12482s.
120 Driving and operation Brake assist Self testing When the engine is started and the vehicle starts off, the system performs a self-check, which may be audible. When the brake pedal is rapidly and forcefully depressed, the vehicle is automatically braked with maximum brake force amplification in order to obtain the shortest possible braking distance during full-on braking (brake assist). Fault 9 Warning Maintain steady pressure on the brake pedal for as long as full-on braking is to continue.
Driving and operation Wheels, tyres Suitable tyres or limitations 3 191. Tyres fitted in the factory are adapted to the chassis and provide optimum driving comfort and safety. Changing tyre/wheel type If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogram the electronic speedometer and make other vehicle modifications. After converting to a different tyre size, have the adhesive label with tyre pressures replaced.
122 Driving and operation Always inflate the spare wheel 3 to the pressure specified for full load. Do not reduce tyre pressure when the tyres are warm. Otherwise the pressure may drop below the permissible minimum when the tyres cool down. After having checked the tyre pressure, tighten the valve caps using the valve cap key. Incorrect inflation pressures will impair safety, vehicle handling, comfort and fuel economy and will increase tyre wear. Picture no: 9358t.
Driving and operation 123 General information z The danger of aquaplaning is greater if the tyres are worn. z Tyres age, even if they are little used or not used at all. We recommend tyre replacement no later than every 6 years. z Never fit used tyres the previous history and use of which you do not know. Picture no: 6457u.tif Tread depth Check tread depth regularly. For reasons of safety, tyres should be replaced when their tread depth has worn down to 2 to 3 mm (winter tyres: 4 mm).
124 Driving and operation Tyre designations Meanings: Winter tyres 3 Instructions on fitting new tyres 3 121. e.g. 175/70 R 14 79 T Limitations 3 191. 175 = 70 = Winter tyres improve driving safety at temperatures below 7 C. R 14 79 = = = T = Tyre width in mm Cross-section ratio (tyre height to tyre width in %) Belt type Radial Rim diameter in inches Load index e. g.
Driving and operation Remove the wheel trims when using tyre chains 3 137. Tyre chains may only be used at speeds up to 50 km/h. When travelling on roads that are free of snow, they may only be used for brief periods. 9 Warning Damage may lead to tyre blowout. Picture no: 6459u.tif Tyre chains 3 Limitations 3 191. Tyre chains are only permitted on the driven wheels (front axle). They must be fitted to the tyres symmetrically in order to achieve a concentric fit.
126 Driving and operation Towing equipment 3 Only use towing equipment that has been approved for your vehicle. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment. Installation dimensions of towing equipment 3 197. Towing equipment with fixed coupling ball bar 3 In the case of trailers/caravans with brake, attach break-away stopping cable to eye to right of coupling ball bar.
Driving and operation Caravans/trailers with LED turn signals require a provision that make bulb replacement as with standard bulbs possible. Handling is greatly influenced by the loading of the trailer/caravan. Loads should therefore be secured so that they cannot slip and be placed in the centre of the trailer/caravan if possible, i.e. above the axle. Picture no: 13228s.tif Driving characteristics, towing tips In the case of trailers/caravans with brakes, attach breakaway stopping cable to eye.
128 Self-help, vehicle care Self-help, vehicle care Diesel fuel system, bleeding ............... Bonnet .................................................. Starting the engine with jump leads 3 Towing .................................................. Warning triangle ¨ 3 and first-aid kit (cushion) + 3 .................................... Spare wheel 3...................................... Jack £ 3 and vehicle tools 3 ............ Changing wheels ................................. Tyre repair kit 3 ......
Self-help, vehicle care 129 Starting the engine with jump leads 3 Do not start by quick charger or by pushing or towing. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle. 9 Warning Picture no: 18097s.tif Lift the safety catch and open the bonnet. Dirt or snow on the bonnet may drop onto the windscreen when the bonnet is opened and block the air intake. Air intake 3 99. Picture no: 15123s.tif Secure the bonnet support.
130 Self-help, vehicle care z Use a booster battery with the same voltage (12 volts). Its capacity (Ah) must not be much less than that of the discharged battery. z Use jump leads with insulated terminals and a cross section of at least 16 mm2 (25 mm2 for diesel engines). z Do not disconnect the discharged battery from the vehicle. z Switch off all unnecessary electrical consumers. z Do not lean over the battery during jump starting. Picture no: 15286a.
Self-help, vehicle care 131 Route the leads so that they cannot catch on rotating parts in the engine compartment. To start the engine: 1. Start the engine of the vehicle providing the jump start. 2. After 5 minutes, start the other engine. Start attempts should be made at intervals of 1 minute not last longer than 15 seconds. 3. Allow both engines to idle for approx. 3 minutes with the leads connected. 4. Switch on electric loads (e.g. light, heated rear window) of the vehicle receiving the jump start.
132 Self-help, vehicle care Switch on ignition to release steering column lock and to permit operation of brake lamps, horn and windscreen wipers. When the engine is not running, considerably more force is needed to brake and steer. Manual transmission in neutral; manual transmission automated 3 in N. To prevent the entry of exhaust fumes from the towing vehicle, switch on the air recirculation 3 and close the windows. Caution Drive slowly. Do not drive jerkily.
Self-help, vehicle care Picture no: 18110s.tif Towing another vehicle Attach a tow rope 3 – or better still a tow rod 3 – to the rear towing eye on the right side of the vehicle underbody, but never to the rear axle. The towing eye is only to be used for towing and not for vehicle recovery. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. Picture no: 12459s.
134 Self-help, vehicle care Picture no: 12462s.tif Combo van The warning triangle and the first aid cushion or box are kept in the compartment behind the driver’s seat. When the vehicle is being loaded, please ensure that nothing protrudes over the bottom edge of the opening. Disengage flap 3 by pressing retaining lug and remove. Picture no: 12454s.tif Spare wheel 3 The spare wheel is stored beneath the floor. 1.
Self-help, vehicle care Picture no: 16493s.tif 7. Place the replaced wheel in the spare wheel holder with the outside of the wheel facing upwards. If a full specification wheel is stowed, do not fit the spacer ring between the wheel and the vehicle underbody. 8. Lift the spare wheel holder, insert the safety cable. 9. Lift the spare wheel holder and engage in the catch. The open side of the catch must point towards the rear. 10.
136 Self-help, vehicle care Information on directional tyres 3 Fit directional tyres such that they roll in the direction of travel. The rolling direction is indicated by a symbol (e.g. an arrow) on the sidewall. The following applies to tyres fitted opposing the rolling direction: z Driving conditions may be altered. Have the defective tyre replaced as soon as possible. z Do not drive faster than 80 km/h. z Drive especially carefully in wet and snowy weather.
Self-help, vehicle care Changing wheels z Use the jack only to change wheels. There may be a tyre repair kit instead of a spare wheel 3 142. z If the ground on which the vehicle is standing is soft, a solid board (max. 1 cm thick) should be placed under the jack. Make the following preparations and observe the following information: Picture no: 12461s.tif Combo van The jack and the vehicle tools are secured behind the driver’s seat. The jack is secured in place by a wing screw.
138 Self-help, vehicle care Picture no: 12483s.tif 1. Prise off the hub cap using a screwdriver, positioning the screwdriver at the recess at the side of the hub cap. Vehicle tools 3 136. Picture no: 11641s.tif Pull off the wheel trim with the hook 3. Vehicle tools 3 136. On some versions, the wheel trim is removed together with the wheel bolts. For wheel trims with visible wheel bolts 3, the trim can remain on the wheel. The retaining rings 3 at the wheel bolts must not be removed.
Self-help, vehicle care Picture no: 11642s.tif Alloy wheels with anti-theft lock 3: unscrew the hub cap with anti-theft key and remove it. Vehicle tools 3 136. Picture no: 11643s.tif 2. Push the wheel bolt wrench 3 on as far as possible and slacken the wheel bolts half a turn. Picture no: 18111s.tif 3. The jacking points are marked.
140 Self-help, vehicle care 5. Unscrew the wheel bolts. On some versions, the wheel trim is removed together with the wheel bolts. If there are lock washers 3 on the wheel bolts, these must not be removed. 6. Changing wheels. Notes on spare wheel 3 134. Notes on temporary spare wheel 3 125, 3 135, 3 191. Picture no: 11645s.tif 4. Pre-adjust the jack 3 to the required height. Position the jack arm in the front or rear so that the jack claw (arrow in picture) grips the vertical web in the recess.
Self-help, vehicle care 9. Push the wheel bolt wrench 3 on as far as possible and tighten crosswise. Tightening torque is 110 Nm. Alloy wheels 3: put hub cap on and engage, inserting pin on rear of hub cap into relevant hole in wheel. Alloy wheels with anti-theft lock 3: Put hub cap on. Insert and tighten antitheft lock 3. 10. Before refitting the wheel trim, clean the wheel around the retaining clips. Valve symbol 3 on back of wheel trim must point towards valve on wheel. Picture no: 11647s.tif 7.
142 Self-help, vehicle care Tyre repair kit 3 Minor damage to the tyre tread or sidewall can be repaired with the tyre repair kit. Do not remove the foreign body from the tyre. Tyre damage exceeding 4 mm or that is on the rim cannot be repaired with the tyre repair kit. 9 Warning Do not drive faster than 80 km/h. Do not use the temporary spare wheel for a lengthy period. Steering and handling may be affected. Important information 3 145.
Self-help, vehicle care Picture no: 15319t.tif 4. Screw the compressor air hose to the connection on the sealant bottle. 5. Fit the sealant bottle in the retainer on the compressor. Set the compressor near the tyre in such a way that the sealant bottle is upright. 6. Remove the valve cap from the defective tyre. Picture no: 15795t.tif 7. Screw the filler hose to the tyre valve. 8. The switch on the compressor must be set to §. 9.
144 Self-help, vehicle care Drain excess tyre pressure with the button over the pressure indicator. Do not run the compressor for more than 10 minutes - see "Important information" 3 145. 15. Detach the tyre repair kit. Screw the filler hose to the free connection on the sealant bottle. This prevents sealant leakage. Stow the tyre repair kit in the luggage compartment. 16. Wipe away any sealant spill with a cloth. Picture no: 15797t.
Self-help, vehicle care 145 Important The driving comfort of the repaired tyre is greatly lessened. Have such tyres replaced. If the compressor makes abnormal noises or heats up greatly, switch it off for at least 30 minutes. The integrated safety valve opens at a pressure of 7 bar. Protect the compressor from moisture and rain. The sealant can only be stored for approx. 4 years. After this time, the sealing properties can no longer be guaranteed. Heed the expiration date on the sealant bottle.
146 Self-help, vehicle care Always use fuses with the correct current value. This is shown on each fuse, and is also indicated by the fuse colour and the plug-in location in the fuse box. Different versions of fuses are used. Picture no: 11651s.tif Before replacing a fuse, turn off the respective switch and the ignition. Slot fuse-gripping tool onto fuse and withdraw it. Picture no: 12892j.tif A defective fuse can be recognized by its melted wire.
Self-help, vehicle care No. 5 6 7 8 9 10 11 12 Picture no: 15543s.tif Fuses and the most important circuits they protect Some circuits may be protected by several fuses. The figures on pages 147, 148 depict the fuse boxes of vehicles with engine Z 13 DTJ1). Fuse boxes of other engines are depicted on pages 149, 150. No. 1 2 1) Circuit Central control unit Engine control unit Sales designation 3 184. No.
148 Self-help, vehicle care No. 26 No. 19 20 21 22 23 24 Picture no: 15544s.tif Circuit Electric window (right) – – Central control unit, immobilizer Windscreen wipers Infotainment system, information display, light switch, courtesy lamp, instruments, EPS No.
Self-help, vehicle care No. 30 31 32 33 34 35 36 37 No. 27 Picture no: 11743s.tif Circuit Seat heater (left) No.
150 No. 38 39 40 41 42 43 44 45 46 47 48 49 50 51 Self-help, vehicle care Circuit Left tail lamp, left parking lamp Right tail lamp, right parking lamp Brake lamps Fog lamps Fog tail lamp Main beam (left) Main beam (right) Ventilation fan Engine control unit Heated rear window Starter EPS ABS Petrol engine: manual transmission automated Diesel engine: engine control unit No. 52 Picture no: 11744s.tif Circuit Radiator fan No.
Self-help, vehicle care 151 Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with your bare hands. The replacement bulb must be in accordance with the data on the base of the defective bulb. Do not exceed wattage given on bulb base. To change the bulbs on the left side, open the fuse box cover. With the Z 13 DTJ engine1), also pull the relay box in front of the fuse box upwards out of the guides.
152 Self-help, vehicle care Picture no: 16076s.tif Picture no: 16077s.tif 3. Push bulb on plug connector downward. 5. Detach plug connector from bulb base. 4. Remove bulb with connector from reflector housing. 7. Insert the bulb with connector so that the lug engages in the recess in the reflector. 6. Plug the plug onto the new bulb. 8. Place headlamp protective cover in position and close. Picture no: 16078s.tif Main beam 1. Open bonnet and engage support. 2.
Self-help, vehicle care Picture no: 16079s.tif Picture no: 16080s.tif 3. Detach plug connector from bulb. 5. Remove bulb from reflector housing. 4. Disengage spring wire clip from retaining lugs by moving it forward and swivelling it to the side. 6. When fitting the new bulb, insert lugs in the reflector recesses. 7. Engage spring wire clip, plug connector onto bulb. 8. Place headlamp protective cover in position and close. 153 Picture no: 16078s.tif Parking lamps 1. Open bonnet and engage support.
154 Self-help, vehicle care Picture no: 16081s.tif Picture no: 16082s.tif 4. Remove side light bulb mounting from reflector. 7. Insert bulb socket in reflector. 5. Remove bulb from socket. 9. Place headlamp protective cover in position and close. 6. Insert new bulb. 8. Attach connector to main beam bulb. Picture no: 16083s.tif Front indicator lamps 1. Open bonnet and engage support. 2. Rotate bulb holder to left and disengage.
Self-help, vehicle care Picture no: 16084s.tif 3. Push bulb into holder a little, rotate left and remove. 4. Insert new bulb. 5. Engage holder into reflector by rotating to the right. Picture no: 15211s.tif 155 Picture no: 15212s.tif Ellipsoidal headlamp system 3. Detach plug connector from bulb. Dipped beam Headlamp system with separate bulbs for dipped beam (inner bulbs) and main beam (outer bulbs). 4. Disengage the spring wire clip from the lugs and swivel it aside. 1.
156 Self-help, vehicle care Main beam, parking lamps Have bulb replacement carried out by a workshop. Side turn signal lamps Have bulb replacement carried out by a workshop. Fog lamps 3 Have bulb replacement carried out by a workshop. Picture no: 15213s.tif Picture no: 15214s.tif Front indicator lamps 1. Open bonnet and engage support. 3. Push bulb into holder a little, rotate left and remove. 2. Rotate bulb holder to left and disengage. 4. Insert new bulb. 5.
Self-help, vehicle care Picture no: 12449s.tif Tail lamps 1. Disengage cover by pressing retaining lugs and remove. Picture no: 13725s.tif 2. Detach plug connector from bulb mounting. 3. Grip the bulb housing from the outside, slacken the two knurled nuts using the wheel bolt spanner 3 and unscrew by hand. 4. Detach bulb housing. 5. Press retaining lugs on bulb mounting together and remove bulb mounting, as shown in illustration 13726 S. 157 Picture no: 13726s.
158 Self-help, vehicle care Picture no: 15135s.tif Number plate lamps 1. Unscrew both screws. Remove lamp insert. Picture no: 15136s.tif 2. Press bulb slightly towards spring clip and remove. 3. Insert new bulb. 4. Insert lamp insert and secure using a screwdriver. Picture no: 11667s.tif Courtesy lamps Front courtesy lamp 1. Prise lamp out of recess using a screwdriver.
Self-help, vehicle care Picture no: 11668s.tif 2. Press bulb slightly towards spring clip and remove. 3. Insert new bulb. 4. Insert lamp in opening and engage in position. Picture no: 11669s.tif Front courtesy lamp with reading lamps 3 1. Disengage and remove lens at the position located in the illustration using a screwdriver. 2. Remove bulb from socket. Picture no: 11670s.tif 3. Insert new bulb. 4. Mount lens and engage in position.
160 Self-help, vehicle care Instrument illumination, Information display illumination 3 Have bulb replacement carried out by a workshop. Vehicle care When caring for your vehicle, observe all national environmental regulations, particularly when washing it. Regular, thorough care helps to improve the appearance of your vehicle and maintain its value over the years. It is also prerequisite for warranty claims for any paint or corrosion damage.
Self-help, vehicle care Washing The paintwork of your vehicle is exposed to environmental influences. Wash and wax your vehicle regularly. When using automatic car washes, select a programme that includes waxing. Bird droppings, dead insects, resin, pollen and the like should be cleaned off immediately, as they contain aggressive constituents which can cause paint damage. When using a car wash, follow the carwash manufacturer’s instructions. Switch off the windscreen wipers 3.
162 Self-help, vehicle care Exterior lights Headlamp and other lamp lens are made of plastic. Do not use any abrasive or caustic agents, do not use an ice scraper, and do not clean them dry. Plastic and rubber parts Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body. Use interior cleaner if necessary. Do not use any other agent. Avoid solvents and petrol in particular. Do not use highpressure jet cleaners.
Self-help, vehicle care Underbody Some areas of the vehicle underbody have a PVC undercoating while other critical areas have a durable protective wax coating. After the underbody is washed, check the underbody and have more protective wax applied if necessary. Bitumen/rubber materials could damage the PVC coating. Have underbody work carried out by a workshop. Before and after winter, wash the underbody and have the protective wax coating checked.
164 Opel Service, maintenance Opel Service, maintenance Scheduled maintenance Service plan The service intervals apply to normal operating conditions. For extreme operating conditions, 3 171.
Opel Service, maintenance European service plan Service work after year1) km (x 1000)1) 1 30 x 2 60 x Check and correct windscreen wipers, windscreen washer system and headlamp washer system x x Check and correct coolant level and frost protection (pale orange)2) Note freeze protection temperature in the Service and Warranty Booklet (confirmation box) Check water hoses for leaks and check to make sure they are firmly seated x x Check and correct brake fluid level2) x Check battery clamps to make
166 Opel Service, maintenance Service work after year1) km (x 1000)1) 1 30 2 60 3 90 4 120 5 150 ⊕ Replace toothed belt and tension roller Z 16 YNG every 6 years/90,000 km Z 17 DTH every 10 years/90,000 km Z 16 XEP every 10 years/150,000 km Change engine oil and oil filter ⊕o Drain water from diesel fuel filter (with high humidity and/or low fuel grade) Empty oil separator, Z 16 YNG x x x x x x x x x x every 4 years/60,000 km Replace and drain water from fuel filter, Z 13 DTJ, Z
Opel Service, maintenance Service work ⊕ after year1) km (x 1000)1) 167 Visually inspect steering bellows, track rods and axle drive 1 30 x 2 60 x 3 90 x 4 120 x 5 150 x Check track-rod ends and suspension ball joints x x x x x Change brake and clutch fluid (manual transmission automated) every 2 years Undo wheel mounting and tighten to 110 Nm torque During assembly, lightly lubricate wheel bolt tapers with grease or oil x Check tyre condition; check and correct tyre pressures (including
168 Opel Service, maintenance International service plan Service work after year1) km (x 1000)1) 1 15 x 2 30 x Check and correct windscreen wipers, windscreen washer system and headlamp washer system x x Check and correct coolant level and frost protection (pale orange)2) Note freeze protection temperature in the Service and Warranty Booklet (confirmation box) Check water hoses for leaks and check to make sure they are firmly seated x x Check and correct brake fluid level2) x Check battery clam
Opel Service, maintenance Service work after year1) km (x 1000)1) 1 15 2 30 3 45 4 60 169 5 75 ⊕ Replace toothed belt and tension roller Z 16 YNG every 6 years/90,000 km Z 17 DTH every 10 years/90,000 km Z 16 XEP every 10 years/150,000 km Change engine oil and oil filter ⊕o Drain water from diesel fuel filter (with high humidity and/or low fuel grade) Empty oil separator, Z 16 YNG x x x x x x x x x x every 4 years/60,000 km Replace and drain water from fuel filter, Z 13 DTJ, Z 17
170 Opel Service, maintenance Service work after year1) km (x 1000)1) Visually inspect steering bellows, track rods and axle drive Check track-rod ends and suspension ball joints ⊕ 1 15 x 2 30 x 3 45 x 4 60 x 5 75 x x x x x x Change brake and clutch fluid (manual transmission automated) every 2 years Undo wheel mounting and tighten to 110 Nm torque During assembly, lightly lubricate wheel bolt tapers with grease or oil x Check tyre condition; check and correct tyre pressures (including the
Opel Service, maintenance Additional service work Additional work ⊕ Additional work is work which is not required for every service but can be carried out along with a regular service. Time allowances for such work are not included within the scope of a regular service and must be accounted for separately. However, it is more cost effective to carry out this work as part of a planned service than to have it done separately.
172 Opel Service, maintenance Engine oil Engine oil is identified by its grade and viscosity. When choosing which engine oil to use, grade is more important than viscosity. Topping up engine oil Oil from different manufacturers and of different brands can be mixed providing they meet the specified engine oil criteria (grade and viscosity). The new GM-Dexos 2 engine oil grade is currently the highest grade. If it is not available, the other engine oil grades that are listed must be used.
Opel Service, maintenance The service interval display takes account of off-the-road periods during which the battery is disconnected. Flexible service interval 3 The length of the service intervals is based on several parameters stemming from usage. For this reason, various engine-specific data is continually gathered and is used to calculate the remaining distance until the next service. Picture no: 14419s.
174 Opel Service, maintenance Genuine Opel Parts and Accessories We recommend that you use "Genuine Opel Parts and Accessories" and conversion parts approved expressly for your vehicle type. These parts have undergone special tests to establish their reliability, safety and specific suitability for Opel vehicles. Despite continuous market monitoring, we cannot assess or guarantee these attributes for other products, even if they have been granted approval by the relevant authorities or in some other form.
Opel Service, maintenance Picture no: 18113s.tif Engine oil On vehicles with engine oil level check 3, the engine oil level is monitored automatically 3 70. We recommend that you check the engine oil level before starting a long journey. Picture no: 13212s.tif Check with the vehicle on a level surface. The engine must be at operating temperature and switched off for at least 5 minutes. 175 Picture no: 16495s.
176 Opel Service, maintenance Picture no: 18114s.tif We recommend that you use the same engine oil as was used the last time it was topped up. Picture no: 12125s.tif The engine oil level must not exceed the MAX mark on the dipstick. Caution If there is too much engine oil, the excess must be drained or suctioned out. Picture no: 12126s.tif The amount must be between the MIN and MAX marks 3 195. Fit the cap on straight and tighten it.
Opel Service, maintenance Diesel fuel filter Coolant On the event of engine oil change, have fuel filter checked for possible water residue by a workshop. The coolant provides anti-freeze protection down to approx. -28 C. Caution Illumination of A indicates water in the fuel filter 3.
178 Opel Service, maintenance Top up with anti-freeze. If no anti-freeze is available, fill with clean tap water or distilled water. Have the anti-freeze concentration checked. Have the cause of coolant loss rectified by a workshop. Caution Too low a coolant level can cause engine damage. Fit the cap on straight and tighten it. Picture no: 13213s.tif Coolant level In a closed cooling system, there is hardly any loss.
Opel Service, maintenance 179 Brake fluid 9 Warning Brake fluid is poisonous and corrosive. Do not allow it to come into contact with eyes, skin, fabrics or painted surfaces. Changing brake fluid Brake fluid is hygroscopic, i. e. it absorbs water. If the brakes become hot, such as when driving on long downhill stretches, vapour bubbles can form in the water, which can have an extremely adverse effect on braking power (depending on the proportion of water).
180 Opel Service, maintenance Laying up the vehicle for more than 4 weeks can lead to battery discharge. Disconnect the negative terminal of the vehicle battery. Ensure the ignition is switched off before connecting or disconnecting the vehicle battery. Protecting electronic components Picture no: 11678s.tif Picture no: 13488a.tif Windscreen washer system Battery Reservoir for windscreen washer and rear windscreen washer at driver’s side in engine compartment.
Opel Service, maintenance Laying the vehicle up for a long period of time If the vehicle is to be laid up for several months, the following work should be undertaken to prevent damage. z Wash and wax the vehicle 3 161. z Have the wax in the engine compartment and underbody checked. z Clean and preserve rubber seals. z Change engine oil. z Check anti-freeze and corrosion protection 3 177. z Check the coolant level; top up anti-freeze if necessary 3 178. z Drain the windscreen washer system.
182 Technical data Technical data Vehicle data......................................... Engine data.......................................... Performance......................................... Fuel consumption, CO2-emissions...... Fuel consumption, natural gas........... Weights, payload and roof load ........ Tyres ..................................................... Capacities ............................................ Dimensions ...........................................
Technical data 183 Engine code and engine number. Marked on engine block at left side of engine in petrol engines, and beneath diesel injection pump at right side of engine in diesel engines. Picture no: 13329j.
184 Technical data Engine data Sales designation Engine identifier code 1.4 TWINPORT CNG Z 14 XEP Z 16 YNG 1.3 CDTI Z 13 DTJ 1.7 CDTI Z 17 DTH 4 4 4 4 Piston displacement [cm ] 1364 1598 1248 1686 Brake horse power [kW/bhp] at rpm 66 5600 69 6200 55 4000 74 4400 Torque [Nm] at rpm 125 4000 133 4200 170 1750 to 2500 240 2300 Petrol Natural gas/petrol Diesel Diesel 95 (P)3) 98 (PP)3) 91 (R)3)4) – 95 (P)3) 98 (PP)3) – – – – – 49 (D)5) – – – 49 (D)5) Max.
Technical data Performance Engine Z 14 XEP Z 16 YNG Z 13 DTJ Z 17 DTH 164 – 165 – 1522) 1522) 170 – 1) Maximum speed [km/h] 5-speed manual transmission Manual transmission automated 1) 2) The maximum speed is achievable with a maximum of half payload. Optional equipment may reduce the specified maximum speed of the vehicle. Specific version with electronic speed limitation at 125 km/h.
186 Technical data Fuel consumption, CO2-emissions Directive 80/1268/EEC (last changed by 2004/3/EC) has applied for the measurement of fuel consumption since 1996. The directive is oriented to actual driving practices: Urban driving is rated at approx. 1/3 and off-road driving with approx. 2/3 (urban and extra-urban consumption). Cold starts and acceleration phases are also taken into consideration. The specification of CO2 emission is also a constituent of the directive.
Technical data Fuel consumption, CO2 emissions (up to tyre width of 185 mm) Engine Z 14 XEP Z 13 DTJ Z 17 DTH Manual/manual transmission automated urban [l/100 km] extra-urban [l/100 km] altogether [l/100 km] CO2 [g/km] 7.9/– 5.2/– 6.2/– 148/– 6.1/ 5.9 4.5/ 4.5 5.1/ 5.0 134/135 6.6/– 4.4/– 5.2/– 140/– Engine Z 14 XEP Z 13 DTJ Z 17 DTH Manual/manual transmission automated urban [l/100 km] extra-urban [l/100 km] altogether [l/100 km] CO2 [g/km] 8.1/– 5.4/– 6.4/– 153/– 6.3/ 6.1 4.7/ 4.7 5.3/ 5.
188 Technical data Fuel consumption (H gas)1) Engine Z 16 YNG Manual transmission urban [m3/100 km] extra-urban [m3/100 km] altogether [m3/100 km] 10.1 5.9 7.5 Fuel consumption (H gas)1) Engine Z 16 YNG Manual transmission urban [kg/100 km] extra-urban [kg/100 km] altogether [kg/100 km] 6.6 3.9 4.
Technical data Weights, payload and roof load The payload is the difference between the permitted gross vehicle weight (see identification plate 3 182) and the EC kerb weight. To calculate the kerb weight, enter the data for your vehicle below: z Kerb weight from Table 1 3 190 z Weight of heavy accessories from Table 2 3 190 Total +.............. kg +.............. kg =.............. kg is the EC kerb weight.
190 Technical data Weights (kg), Table 1, kerb weight1) Combo van Engine without/with air Z 14 XEP conditioning Z 16 YNG [kg] Manual transmission Manual transmission automated 1190/1350 – 1322/1352 – Z 13 DTJ 1285/1420 1285/1420 Z 17 DTH 1320/1455 – Manual transmission manual transmission automated 1235/1265 – 1367/1397 – Z 13 DTJ 1325/1355 1325/1355 Z 17 DTH 1365/1395 – Weights (kg), Table 1, kerb weight Combo Engine without/with air Z 14 XEP conditioning Z 16 YNG [kg] Weigh
Technical data Tyres Not all tyres available on the market currently meet the structural requirements. We recommend that you consult an Opel Partner concerning suitable tyre makes. These tyres have undergone special tests to establish their reliability, safety and specific suitability for Opel vehicles. Despite continuous market monitoring, we are unable to assess these attributes for other tyres, even if they have been granted approval by the relevant authorities or in some other form.
192 Technical data Tyre pressure (overpressure) Combo van Engine Fully loaded [kPa/bar] Front Rear Front Rear R 141)2), R 142), 3)4) 240/2.4 240/2.4 240/2.4 350/3.5 Z 13 DTJ 175/70 R 141)2), 175/65 R 142), 185/55 R 153)4), 185/60 R 15 240/2.4 240/2.4 240/2.4 350/3.5 Z 17 DTH 185/60 R 15, 185/55 R 154) 240/2.4 240/2.4 240/2.4 350/3.5 Z 16 YNG 185/60 R 15, 185/55 R 154) 240/2.4 240/2.4 240/2.4 350/3.5 all T 115/70 R 16 (Temporary spare wheel)5) 420/4.2 420/4.2 420/4.
Technical data Tyre pressure (overpressure) Combo Engine Tyres 1) Comfort when loaded with up to 3 persons [kPa/bar] Fully loaded [kPa/bar] Front Rear Front Rear Z 14 XEP 175/70 R 14 , 175/65 R 14, 185/55 R 152)3), 185/60 R 154), 185/65 R 15, 195/45 R 16, 195/50 R 16 240/2.4 240/2.4 240/2.4 350/3.5 Z 13 DTJ 175/70 R 141), 175/65 R 14, 185/55 R 152)3), 185/60 R 154), 185/65 R 15 240/2.4 240/2.4 240/2.4 350/3.5 Z 17 DTH 185/60 R 15, 185/55 R 153), 185/65 R 15, 195/50 R 16 240/2.4 240/2.
194 Technical data Tyre pressure (overpressure) Combo Tramp/Arizona Comfort when loaded with up to 3 persons [kPa/bar] Fully loaded [kPa/bar] Engine Tyres Front Rear Front Rear Z 14 XEP, Z 16 YNG, Z 13 DTJ, Z 17 DTH 185/60 R 15, 185/65 R 151) 240/2.4 240/2.4 240/2.4 350/3.5 1) Recommended: Goodyear Eagle Hydragrip.
Technical data Capacities Engine oil Engine Z 14 XEP Z 13 DTJ Z 17 DTH Incl. filter [l] 3.5 3.5 5.0 Between MIN and MAX [l] 1.0 1.0 1.0 Engine Z 14 XEP Z 13 DTJ Z 17 DTH Petrol/diesel, nominal capacity [l] 52 52 52 Fuel tank Engine oil Engine Z 16 YNG Incl. filter [l] 3.5 Between MIN and MAX [l] 1.0 Fuel tank Engine Z 16 YNG Natural gas, nominal capacity [kg] petrol, nominal capacity [l] 17.51) 14 1) 17.5 kg (average fill limit), corresponding to a tank volume of 108 l.
196 Technical data Dimensions Combo van Combo Overall length [mm] 4322 4322 Overall width [mm] 1684 1684 Width with two exterior mirrors [mm] 1892 1892 Height at kerb weight [mm] 1801 1801 Length of luggage compartment [mm] 1787 /2700 10203)/16644)/27002) Width of luggage compartment [mm] without/with 1/with 2 sliding doors min. width between wheel housings 1348/1399/1449 1107 –/1399/1449 1107 Max.
Technical data Mounting dimensions of towing equipment with fixed coupling ball bar All dimensions relate to trailer towing equipment approved by Opel. Dimension mm A 71 B 929 C 515 D 506.3 E 274.3 F 149 G 401.7 H 384 I 398 9 Warning Only use towing equipment approved for your vehicle. We recommend entrusting retrofitting of towing equipment to your workshop.
198 Index Index A B ABS (Anti-lock Braking System) ........... 119 Accessories ............................................. 133 Accessory socket ..................................... 61 Air intake .................................................. 99 Air recirculation system ........................... 97 Air vents ................................................... 93 Airbags ..................................................... 56 Alarm ........................................................
Index C Capacities .............................................. 195 Car Pass .................................................... 20 Caravan/trailer towing ..................106, 125 Care ........................................................ 160 Catalytic converter ............... 114, 118, 129 Central locking system ......................23, 24 Centre console lighting ........................... 88 Changeover inhibitor ............................. 114 Changing the remote control battery ....
200 Index F G Fan ............................................................ 94 Fault .......................................................... 37 Filling station Capacities ........................................... 195 Engine oil level ................................... 175 Fuel .............................................110, 184 Opening the bonnet .......................... 128 Tyre pressure ...................................... 191 Vehicle data ...............................
Index K Key Extending ............................................. 20 Ignition lock .......................................... 16 Locking doors ...........................20, 23, 24 Remove ................................................. 17 Starting ...........................................16, 21 Starting the engine .............................. 16 Keys ...................................................... 2, 20 L Language selection ................................. 80 Lashing eyes .................
202 Index P R S Paintwork damage ................................ 161 Parking ..................................................... 17 Parking lamps ............................................ 6 Bulb replacement ............................... 153 Parking the vehicle .................................. 17 Parts ........................................................ 174 Pedals ..................................................... 107 Performance ...................................185, 186 Petrol .....
Index Signal system ........................................... 13 Sliding doors ............................................ 27 Spare fuses ............................................. 145 Spare keys ................................................ 20 Spare wheel ....................................134, 137 Speed ..............................................108, 109 Fuel consumption ......................108, 109 Speedometer ............................................ 71 Starter switch .................
204 Index W Warning buzzers ...................................... 82 Warning triangle .................................... 133 Washer fluid reservoir, windscreen washer system ................. 180 Wheel trim .............................................. 124 Wheels .................................................... 121 Wheels, tyres .......................................... 121 Windows Demisting and defrosting .............96, 98 Windscreen washer system .......13, 83, 180 Antifreeze protection .....
Copyright by ADAM OPEL GmbH, Rüsselsheim, Germany. The information contained in this publication is valid as of the date indicated below. Adam Opel GmbH reserves the right to make changes to the technical specifications, features and design of the vehicles relative to the information contained in this publication, as well as changes to the publication itself. Edition: August 2009, ADAM OPEL GmbH, Rüsselsheim. Printed on chlorine-free bleached paper. KTA-2387/13-en 24 439 257 Art.-Nr.
