Manual

TX NR702,602 t n book Page 54 Monday,July 26, 2004 11:05 AM
Basic Operation--Continued
54
I [RECEIVER] _
DIMMER --
_I_ER _EE_
--SLEEP
-- MUTING
You can adjust the brightness of the display.
Press the [RECEIVER] button,
and then press the [DIMMER]
button repeatedly to select:
• Normal+VOLUME light on.
• Normal+VOLUME light oft'.
• Dim+VOLUME light off.
• Dimmer+VOLUMElight off.
Yon can temporarily mute the output of the AV receiver.
_ _ Press the [RECEIVER] button,
iiiiilili!!i!!!iandthenpressthe[MUTING] but-
iiiiiiiiiiii!iiton.
iiiiiiii:i!iiiilililililililililiiiiiiiiiiiiiTheoutput is mutedandthe MUTING
iiiiii:i:ili{i:i:i:i:iiiil]iiiiiiiiii:!i!!i!!i:)!ii:i:i:i:i!!i!ii!iiiiiiiiiiiiiillindicator flashes on the display, as
ii!iiii ii iii!ii; i iiiiiiiiisb°wn.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiToumnutetheaVreceiver, pressthe
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii]MUTING] buttonagain, oradiusttlle
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiivOltll!qe"
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiTheMntefnncti°niscai_]ceHedwhen
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiithe AV receiver is set to Standby.
With the sleep timer, you can set the AV receb'er to auto-
matically turn off after a specified period.
Press the [RECEIVER] button,
and then press the [SLEEP] but-
ton repeatedly to select the
required sleep time.
The sleep time can be set from 90 to 10
minutes in 10 minute steps.
The SLEEP indicator appears on the
display when the sleep timer has been
set, as shown. The specified sleep time
appears on the display for about five
seconds, then the previous display
reappears.
If you need to cancel the sleep timer, press the [SLEEPI
button repeatedly until the SLEEP indicator disappears.
To check the time remaining until the AV receiver sleeps,
press the [SLEEP] button. Note that if you press the
[SLEEPI button while the sleep time is being displayed,
you'll shorten the sleep time by 10 minutes.
Yon can connect a pair of stereo headphones (l/4-inch
phone plug) to the AV receiver's PHONES .iack for pri-
vate listening, as shown.
....... d 'd 5
Notes:
• Always turn down the volmne bet)re connecting your
headphones.
• The speakers are turned off while the headphones plug
is inserted in the PHONES .jack. (Zone 2 speakers are
not turned oft'.)
• When you connect a pair of headphones, the listening
mode is set to Stereo, unless it's already set to Stereo,
Mono, Direct, or Pure Audio (not American
TX-SR602). When you disconnect the headphones,
the previous listening mode is resumed.
• Only the Stereo, Direct, Pure Audio (not American
TX-SR602), and Mono listening modes can be used
with headphones. (The listening modes available also
depends on the currently selected input source.)
• When the mnltichannel input is used, only the front
left and right audio can be heard in the headphones.
On the TX-SR702E, when the Stereo or Mono listen-
ing mode is selected, audio is downmixed for a good
sound.