Manual

m Speakers Type
Normal:
Select this if you've connected your front speakers
normally.
Bi-Amp:
Select this if you've bi-amped your front speakers.
• Powered Zone 2 cannot be used if "Speakers Type" is set to
"Bi-Amp" (_ 56).
N Speaker Terminal Assign
Front High/Front Wide/Zone2
With this setting, you can specify the speakers con-
nected to FRONT HIGH OR FRONT WIDE OR
ZONE 2 SPEAKERS terminals.
Front High:
Front high speakers can be used.
Front Wide:
Front wide speakers can be used.
Zone2:
Zone 2 speakers can be used. (Powered Zone 2
enabled).
• If the "Speakers Type" setting is set to "Bi-Amp", or Powered
Zone 2 cannot be used.
SurrBack/Front High/Front Wide
With this setting, you can specify the speakers con-
nected to SURR BACK OR FRONT HIGH OR
FRONT WIDE SPEAKERS terminals.
Surr Back:
Surround back speakers can be used.
Front High:
Front high speakers can be used.
Front Wide:
Front wide speakers can be used.
• If the "Speakers Type" setting is set to "Bi-Amp", or Powered
Zone 2 cannot be used.
• If "Front High" is selected ill the "Front High/Front Wide/
Zone2" setting, you cannot select "Front High" here.
• If "Front Wide" is selected ill the "SurrBaek/Front High/
Front Wide" setting, you cannot select "Front Wide" here.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify "Full Band" for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker's manuals to determine the
optimum crossover frequencies. If you set up your speak-
ers using Audyssey 2EQ® Room Correction and Speaker
Setup, please make sure manually that any THX speakers
are set to "80Hz(THX)" crossover.
N Subwoofer
Yes:
Select if a subwoofer is connected.
No:
Select if no subwoofer is connected.
N Front
Full Band
40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
• If the "Subwoofer" setting is set to "No", the "Front" setting is
fixed at "Full Band".
N Center*l, Surround*l, Surr Back*2*3*4*5
Full Band
40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
None:
Select if no speaker is connected.
N Front Wide*l*2*4*6, Front High*l *2*4*7
Full Band
40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
None:
Select if no speaker is connected.
*3 "Full Band" can be selected only when "Full Band" is
selected in the "Front" setting.
*2 If the "Surround" setting is set to "None", this setting cannot
be selected.
*3 If the "Surround" setting is set to anything other than "Full
Band", "Full Band" cannot be selected here.
*4 If the "Speakers Type" setting is set to "Bi-Amp" (_ 41 ), or
Powered Zone 2 is being used (_ 56), this setting cannot be
selected.
*5 If you have selected other than "Surr Back" in the "Surf
Back/Front High/Front Wide" setting, this setting cannot be
selected.
*6 If you have selected other than "Front Wide" in the "Front
High/Front Wide/Zone2" or "SurrBaek/Front High/Front
Wide" setting, this setting cannot be selected.
*7 If you have selected other than "Front High" in the "Front
High/Front Wide/Zone2" or "SurrBaek/Front High/Front
Wide" setting, this setting cannot be selected.
N Surr Back Ch
lch:
Select if only one surround back speaker L is con-
nected.
2ch:
Select if two (left and right) surround back speakers
are connected.
• If the "Surf Back" Setting is set to "None" (_ 48), this setting
cannot be selected.
i ii
Erl
41