Manual
Connections
9,TV monitor or projector
(MONITOR OUT)
Video input
S Video input
Component video input
_iiΒΈ)
R (red)
Analog audio
L (white) output
Video output
-- E_mmi S Video output
7, 8. Connecting a satellite tuner, television, or settop
box (VIDEO 3 or 4)
If the satellite tuner or lelevision is equipped with an S video oglput
terminal, connect it to the S VIDEO 3 (or 4) IN terminal with an S
video cable_ If it does not have an S video oglpgt terminal, connect
its video oglput terminal Io the VIDEO 3 (or 4) IN terminal using an
RCA-type video connection cable. You do not need lo connect to
both the S VIDEO 3 (or 4) IN and VIDEO 3 (or 4) IN terminals. If
the satellite tuner or television has component video outputs,
connect them lo one of the COMPONENT VIDEO INPUT jacks.
With the initial settings of the TX-DS898, the VIDEO 3 and
VIDEO 4 input sources are set for the COMPONENT VIDEO
INPUT 2 jack.
If the video connection is made at COMPONENT VIDEO INPUT
1, this must be changed at the Setup menu: Input Setup --_ Video
Setup --_ Component Video (see page 35).
Using an RCA-type audio connection cable, connect the audio
output terminal on the satellite tuner or television to the same
VIDEO 3 (or 4) IN audio jacks on the TX-DS898. Make sure that
you properly connect the left channel to the L jack and the right
channel to the R jack.
If the device has a digital output jack as well, be sure to also connect
it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT
(OPTICAL) jack on the TX-DS898 depending on the device.
With the initial settings of the TX-DS898, the VIDEO 3 input source
is set for digital input at the OPTICAL 3 jack, and the VIDEO 4
input source is set for digital input at the OPTICAL 4 jack.
If the digital connection is made at a different jack, this must be changed
at the Setup menu: Input Setup --_ Digital Setup (see page 33).
9. Connecting a television monitor or projector
(MONITOR OUT)
The TX-DS898 is equipped with a simple Y/C separate circuit and
simple Y/C mixed circuit, Since both the signal from the S VIDEO
and VIDEO inputs m'e output to the MONITOR OUT S VIDEO
output, if the television or projector is equipped with an S video
input, it is unnecessary to connect the video connectors. If it is
equipped with only a video input, connect it to Ihe MONITOR OUT
VIDEO output.
18
If the monitor or projector is equipped with an S video output
terminal, connect it 1o the MONITOR OUT S VIDEO terminal with
an S video cable. If it does no1 have an S video output terminal,
connect its video output terminal to the MONITOR OUT VIDEO
terminal using an RCA-type video connection cable. You do not
need to connect to both the MONITOR OUT S VIDEO and
MONfI'OR OUT VIDEO lerminals. If the device has component
video inputs, connect Ihem to the COMPONENT VIDEO OUTPUT
jacks.
Caution:
Note that the Setup menu will only be displayed on the monitor
connected to MONITOR OUT and not those connected to the
COMPONENT VIDEO OUTPUT jacks.
10. Connecting video camera, etc. (VIDEO 5)
If the device is equipped with an S video oglpgt terminal, connect it
to the S VIDEO 5 IN lerminal with an S video cable. If it does not
have an S video oglpgt terminal, connect its video output terminal to
the VIDEO 5 IN terminal using an RCA-type video connection
cable. You do not need to connect to both the S VIDEO 5 IN and
VIDEO 5 IN terminals.
The VIDEO 5 digital input is fixed to the OPTICAL input on the
front panel.
S Video output
/
Digital output -- U I
(1V01"D'Ekoe5/_/laDmE;ca/VAidelONgaU_ ! _
I
[ Video output ._
Analog output __
Right (red)