Contents AV Receiver HT-RC370 Introduction ...................................2 Connections.................................12 Turning On & Basic Operations ......22 Instruction Manual Advanced Operations .................43 Controlling Other Components...64 Appendix ......................................72 Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit.
Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Precautions 1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer. 3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth.
Supplied Accessories Make sure you have the following accessories: Indoor FM antenna (➔ page 21) AM loop antenna (➔ page 21) Power cord (Chinese models) (➔ page 21) Speaker cable labels (➔ page 13) Speaker setup microphone (➔ page 31) Remote controller (RC-807M) and two batteries (AA/R6) (Note for China: The battery for the remote controller is not supplied for this unit.) * In catalogs and on packaging, the letter at the end of the product name indicates the color.
Contents Introduction Important Safety Instructions ......................................... 2 Precautions....................................................................... 3 Supplied Accessories...................................................... 4 Features ............................................................................ 6 Front & Rear Panels......................................................... 8 Front Panel.....................................................................
Features Amplifier Miscellaneous • 100 Watts/Channel @ 8 ohms (FTC) • 160 Watts/Channel @ 6 ohms (IEC) • 175 Watts/Channel @ 6 ohms (JEITA) • WRAT–Wide Range Amplifier Technology (5 Hz to 100 kHz bandwidth) • Linear Optimum Gain Volume Circuitry • 3-Step Inverted Darlington Circuitry • H.C.P.S.
*1 THX and the THX logo are trademarks of THX Ltd. which may be registered in some jurisdictions. All rights reserved. THX Select2 Plus Before any home theater component can be THX Select2 Plus certified, it must pass a rigorous series of quality and performance tests. Only then can a product feature the THX Select2 Plus logo, which is your guarantee that the Home Theater products you purchase will give you superb performance for many years to come.
Front & Rear Panels Front Panel (North American models) a n o b c p d e q f g h i j k l r (Chinese models) m s t uv w The page numbers in parentheses show where you can find the main explanation for each item.
Display a h b c d ij k For detailed information, see the pages in parentheses.
Rear Panel (North American models) a bc d k e l fg m h i n o p q (Chinese models) a DIGITAL IN COAXIAL and OPTICAL jacks b u REMOTE CONTROL jack c UNIVERSAL PORT jack d ETHERNET port e MONITOR OUT V and S jacks f HDMI IN and OUT jacks g COMPONENT VIDEO IN and MONITOR OUT jacks h FM ANTENNA jack and AM ANTENNA terminal j l Composite, S-Video and analog audio jacks (BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN, GAME IN, PC IN, TV/CD IN and PHONO IN) m Multichannel input jacks (FRONT L/R, CENTER, S
Remote Controller Controlling the AV Receiver a i c b c *1 For detailed information, see the pages in parentheses. a 8RECEIVER button (22) j k d d b ACTIVITIES buttons (42, 70) c REMOTE MODE/INPUT SELECTOR buttons (23) d SP LAYOUT button (41) e Arrow q/w/e/r and ENTER buttons f SETUP button (43) g Listening Mode buttons (34) h DIMMER button (40) e a f To control the AV receiver, press RECEIVER to select Receiver mode.
Connections Connecting the AV Receiver Connecting Your Speakers Connecting the Speaker Cables The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one surround back speaker, connect it to the SURR BACK L terminals.
Speaker Configuration Speaker Connection Precautions The following table indicates the channels you should use depending on the number of speakers that you have. No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings automatically (➔ page 31) or manually (➔ page 46).
Using Dipole Speakers You can use dipole speakers for the surround and surround back speakers. Dipole speakers output the same sound in two directions. Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround dipole speakers (A) should be positioned so that their arrows point toward the TV/screen, while the surround back dipole speakers (B) should be positioned so that their arrows point toward each other, as shown.
Connecting a Power Amplifier If you want to use a more powerful power amplifier, you can use the AV receiver as a preamp. Connect all speaker outputs to the power amplifier. See the manuals supplied with your amplifier for details. Note *1 Specify “None” for any channel that you don’t want to output (➔ page 46).
About AV Connections Connecting AV components : Video & Audio HDMI cable TV, projector, etc. : Video Other cables AV receiver AV receiver Blu-ray Disc/DVD player Blu-ray Disc/DVD player Game console TV, projector, etc. • Before making any AV connections, read the manuals supplied with your AV components. • Don’t connect the power cord until you’ve completed and double-checked all AV connections.
Connecting Components with HDMI VCR or DVD recorder/Digital Video Recorder Game console TV, projector, etc. Blu-ray Disc/DVD player Personal computer Camcorder Satellite/cable set-top box, etc. Connect your components to the appropriate jacks. The default input assignments are shown below. ✔: Assignment can be changed (➔ page 44).
Connecting Your Components The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.
Connect your components to the appropriate jacks. The default input assignments are shown below. See “Connection Tips and Video Signal Path” for more information (➔ page 81). ✔: Assignment can be changed (➔ page 45). No.
Connecting Onkyo u Components 1 Make sure that each Onkyo component is connected with an analog audio cable (connection F in the hookup examples) (➔ page 18). 2 3 Make the u connection (see the illustration). If you’re using an RI Dock, or cassette tape deck, change the Input Display (➔ page 41).
Connecting the Antennas This section explains how to connect the supplied indoor FM antenna and AM loop antenna. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. Caution North American models Chinese models • Be careful not to injure yourself when using thumbtacks. Push. Insert wire. Release. Insert the plug fully into the jack. Insert the plug fully into the jack. Assembling the AM loop antenna Thumbtacks, etc.
Turning On & Basic Operations Turning On/Off the AV Receiver 8ON/STANDBY 8RECEIVER RECEIVER Turning On 1 Press 8ON/STANDBY on the front panel. or Press RECEIVER followed by 8RECEIVER on the remote controller. The AV receiver comes on, the display lights. Turning Off 1 Press 8ON/STANDBY on the front panel. or Press RECEIVER followed by 8RECEIVER on the remote controller. The AV receiver will enter standby mode.
Playback The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings. Controlling Contents of USB or Network Devices See “Controlling Other Components” about the operation of other components (➔ page 67). This section describes the procedure for using the remote controller unless otherwise specified. Press USB or NET first.
j MENU This button returns to top menu of the Internet Radio service. k RETURN This button returns to the previous menu. l 6 This button selects the next song. m 4 This button fast-forwards the current song. n 2 This button stops playback. o MODE You can switch between Standard Mode and Extended Mode during iPod/iPhone playback. Playing an iPod/iPhone via USB This section explains how to play music/video files on the iPod/iPhone.
Extended Mode (Music) control The music content information is displayed (lists are displayed), and you can control the music content while looking at the screen. Top screen list: Playlists, Artists, Albums, Genres, Songs, Composers, Shuffle Songs, Now Playing. Extended Mode (Video) control The video content information is displayed (lists are displayed), and you can control the video content while looking at the screen. Top screen list: Movies, Music Videos, TV Shows, Video Podcasts, Rentals.
3 Use q/w to select a program and then press ENTER. Playback starts. My Music 0 : 11 Greate Artist My Favorite Press MENU to enable selection from the following menu items. ` Stations like this: Stations like the one currently being played back are displayed. ` Add to My Favorites: Adds a station to My Favorites list. Press TOP MENU to go to the top menu of the Internet Radio services. Registering My Favorites*1 You can add the currently playing song or station to the “My Favorites”.
Playing Music Files on a Server You need to connect the AV receiver to your home network (➔ page 87). This section explains how to play music files on a computer or media server through the AV receiver (Server Playback). Windows Media Player 11 Setup This section explains how to configure Windows Media Player 11 so that the AV receiver can play the music files stored on your computer. 1 2 Start Windows Media Player 11. 3 Select the “Share my media” check box, and then click “OK”.
Using Remote Playback Listening to AM/FM Radio 1 Start Windows Media Player 12. To enable remote playback, you must first configure Windows Media Player 12. This section describes the procedure using the buttons on the front panel unless otherwise specified. 2 Press NET. The “NET” screen appears. The NET indicator lights. If it flashes, verify the network connection. 3 Use q/w/e/r to select “dlna”, and press ENTER. A list of media server appears.
■ Tuning into stations by frequency You can tune into AM and FM stations directly by entering the appropriate frequency. ■ Deleting Presets 1 Select the preset that you want to delete. See the previous section. 1 2 While holding down MEMORY, press TUNING MODE. The preset is deleted and its number disappears from the display. On the remote controller, press TUNER repeatedly to select “AM” or “FM”, followed by D.TUN. (Actual display depends on the country.
■ Displaying Radio Text (RT) 1 Press RT/PTY/TP once. The RT information scrolls across the display. Note • The message “Waiting” may appear while the AV receiver waits for the RT information. • If the message “No Text Data” appears on the display, no RT information is available.
Using Basic Functions Using the Automatic Speaker Setup With the supplied calibrated microphone, Audyssey MultEQ® XT automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyssey MultEQ XT then removes the distortion caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain.
3 When you’ve finished making the settings, press ENTER. 9 Use q/w to select an option, and then press ENTER.
Error Messages Changing the Speaker Setup Manually While Audyssey MultEQ® XT Room Correction and Speaker Setup is in progress, one of the error messages below may appear. You can manually make changes to the settings found during Audyssey MultEQ XT Room Correction and Speaker Setup. See also: • “Speaker Configuration” (➔ page 46) • “Speaker Distance” (➔ page 47) • “Level Calibration” (➔ page 48) • “Equalizer Settings” (➔ page 48) MultEQ XT: Auto Setup AUDYSSEY Ambient noise is too high.
Using the Listening Modes Selecting Listening Modes See “About Listening Modes” for detailed information about the listening modes (➔ page 35). ■ Listening Mode Buttons Press RECEIVER first. PURE AUDIO MUSIC MOVIE/TV MOVIE/TV, MUSIC, GAME GAME THX MOVIE/TV button This button selects the listening modes intended for use with movies and TV. MUSIC button This button selects the listening modes intended for use with music.
About Listening Modes The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. ■ Explanatory Notes ij ab c kl f SP LAYOUT a b Front speakers c Center speaker d e Surround speakers f Subwoofer(s) g h Surround back speakers i j Front high speakers k l Front wide speakers Listening mode buttons de gh Input Source The following audio formats are supported by the listening mode.
■ Onkyo-Original DSP Listening Modes Listening Mode Description Orchestra Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.
Listening Mode Description Input Source Speaker Layout Dolby Pro Logic IIx*4 Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides a very natural and seamless surround-sound experience Dolby Pro Logic II that fully envelops the listener. As well as music and movies, video games PL Mo v i e can also benefit from the dramatic spatial effects and vivid imaging. If you’re not using any surround back speakers, Dolby Pro Logic II will be S used instead of Dolby Pro Logic IIx.
Listening Mode Description Neo:6 This mode expands any 2-channel source for up to 7.1-channel playback. It uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener. Ne o : 6 C i n ema Ne o : 6 Mu s i c Ne o : 6 Audyssey DSX*8 Audy s s e y DSX PL Mo v i e DSX PL Mu s i c DSX PL Game En 38 • Neo:6 Cinema S Use this mode with any stereo movie (e.g., TV, DVD, VHS).
Listening Mode TH N eX o : S 62 C i n ema THX S2 Mu s i c THX S2 Game s THX Su r r EX Description Input Source Speaker Layout • Dolby Pro Logic IIz Height + THX Cinema • Dolby Pro Logic IIz Height + THX Music • Dolby Pro Logic IIz Height + THX Games The combination of Dolby Pro Logic IIz Height and THX Cinema/Music/Games modes can be used. The PLIIz indicator lights on the display.
Using the Home Menu Note *1 The Home menu provides you quick access to frequently used menus without having to go through the long standard menu. This menu enables you to change settings and view the current information. The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings. *2 *3 Using the Sleep Timer 1 Press RECEIVER followed by HOME.
Displaying Source Information You can display various information about the current input source as follows. (Components connected to the UNIVERSAL PORT jack are excluded.) 1 Selecting Speaker Layout You can set which speakers you want to use by priority. 1 Press RECEIVER followed by DISPLAY repeatedly to cycle through the available information. The following information can typically be displayed.
Using Easy Macros By using ACTIVITIES in Easy macro mode, you can sequentially operate Onkyo components via simple commands from a single-button press. These commands are user-definable. See “Using Normal Macros” (➔ page 71). 1 Press ACTIVITIES (MY MOVIE, MY TV, or MY MUSIC) to start the Easy macro command. The default sequences of actions are described below. To change the related source component, see “Changing the Source Components” shown later in this chapter.
Advanced Operations Advanced Setup The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings. Common Procedures in Setup Menu This section describes the procedure for using the remote controller unless otherwise specified. RECEIVER On-screen Setup Menus ENTER q/w/e/r MENU 1. 2. 3. 4. 5. 6. 7. 8. 9.
Input/Output Assign Main Menu Input/Output Assign Monitor Out ■ Resolution `Through: Select this to pass video through the AV receiver at the same resolution and with no conversion. `Auto: Select this to have the AV receiver automatically convert video at resolutions supported by your TV. `480p (480p/576p), 720p, 1080i, 1080p Select the desired output resolution. `1080p/24: Select this for 1080p output at 24 frames per second.
Digital Audio Input Note • If no video component is connected to HDMI output (even if the HDMI input is assigned), the AV receiver selects the video source based on the setting of “Component Video Input”. • When an HDMI IN is assigned to an input selector as explained here, the same HDMI IN will be set as a priority in the “Digital Audio Input” (➔ page 45). In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the “Audio Selector” setting (➔ page 55).
Speaker Setup Main menu Note Speaker Setup Some of the settings in this section are set automatically by Audyssey MultEQ® XT Room Correction and Speaker Setup function (➔ page 31). • If the “Speakers Type(Front)” setting is set to “Bi-Amp”, Powered Zone 2 cannot be used. • When the “Powered Zone 2” setting is set to “Yes”, the surround back, front wide and front high speakers cannot be used.
Note *1 *2 *3 *4 “Full Band” can be selected only when “Full Band” is selected in the “Front” setting. If the “Surround” setting is set to “None”, this setting cannot be selected. If the “Surround” setting is set to anything other than “Full Band”, “Full Band” cannot be selected here. If the “Speakers Type(Front)” setting is set to “Bi-Amp”, or the “Powered Zone 2” setting is set to “Yes”, this setting cannot be selected. ■ Surround Back Ch ` 1ch: Select if only one surround back speaker L is connected.
Level Calibration This setting is set automatically by Audyssey MultEQ® XT Room Correction and Speaker Setup function (➔ page 31). Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. ■ Left, Front Wide Left, Front High Left, Center*1, Front High Right, Front Wide Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left `–12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
■ THX Ultra2/Select2 Subwoofer ` No ` Yes If you’re using a THX-certified subwoofer, set this setting to “Yes”. Audio Adjust Main menu Audio Adjust With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. Note • If the “Subwoofer” setting is set to “No”, this setting cannot be selected (➔ page 46).
Dimension `–3 to 0 to +3 With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. Higher settings move the sound field backward. Lower settings move it forward. If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.
DTS Source Setup ■ Neo:6 Music Items can be set individually for each input selector. Center Image ` 0 to 2 to 5 The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. Changing the value from “0” to “5” will spread the sound of the center channel to left and right (outwards).
■ Reference Level Audyssey Dynamic EQ® Reference Level Offset `0dB: This should be used when listening to movies. `5dB: Select this setting for content that has a very wide dynamic range, such as classical music. `10dB: Select this setting for jazz or other music that has a wider dynamic range. This setting should also be selected for TV content as that is usually mixed at 10 dB below film reference.
IntelliVolume Name input area ■ IntelliVolume ` –12dB to 0dB to +12dB in 1 dB steps. With IntelliVolume, you can set the input level for each input selector individually. This is useful if one of your source components is louder or quieter than the others. Use e/r to set the level. If a component is noticeably louder than the others, use e to reduce its input level. If it’s noticeably quieter, use r to increase its input level. BD/DVD 4 - 4.
Picture Adjust Using Picture Adjust, you can adjust the picture quality and reduce any noise appearing on the screen. To view the TV picture while setting, press ENTER. To return to the previous screen, press RETURN. ■ Wide Mode*1*2 This setting determines the aspect ratio. `4:3: `Full: `Zoom: `Wide Zoom: `Auto: According to the input signals and monitor output setting, the AV receiver automatically selects the “4 : 3”, “Full”, “Zoom” or “Wide Zoom” mode.
Note • “Picture Adjust” cannot be used with the NET input selector. This procedure can also be performed on the remote controller by using the Home menu (➔ page 40). *2 When a 3D video source is input, “Wide Mode” is fixed to “Full”. *3 When the “Picture Mode” setting is set to anything other than “Custom”, this setting cannot be used. *4 If the “Resolution” setting is set to “4K Upscaling” (➔ page 44), this setting is fixed to “Off”. *5 Press CLR if you want to reset to the default value.
Listening Mode Preset You can assign a default listening mode to each input source that will be selected automatically when you select each input source. For example, you can set the default listening mode to be used with Dolby Digital input signals. You can select other listening modes during playback, but the mode specified here will be resumed once the AV receiver has been set to standby. Main menu 1 Listening Mode Preset Use q/w to select the input source that you want to set, and then press ENTER.
OSD Setup Tuner ■ On Screen Display ` On ` Off This preference determines whether operation details are displayed on-screen when an AV receiver function is adjusted. Even when “On” is selected, operation details may not be output if the input source is connected to an HDMI IN. For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area. Note that when this setting is changed, all radio presets will be deleted.
■ HDMI Through `Off `Auto: Detects the signal and automatically selects the input source. `BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX, TV/CD, PHONO, PORT: Selects the input source for which the HDMI Through function is enabled. `Last: The HDMI Through function is activated on the input source selected at the time of setting the AV receiver to standby mode.
Network After modifying the network settings, you must confirm the changes by executing “Save”. ■ Proxy URL To use a Web proxy, enter its URL here. ■ Proxy Port If you’re using a Web proxy, enter a proxy port number here. This section explains how to configure the AV receiver’s network settings manually. If your router’s DHCP server is enabled, you don’t need to change any of these settings, as the AV receiver is set to use DHCP to configure itself automatically by default (i.e., DHCP is set to “Enable”).
Remote Controller Setup Main menu Remote Controller Setup Remote Mode Setup See “Looking up for Remote Control Code” (➔ page 67). Lock Setup With this preference, you can protect your settings by locking the setup menus. Main menu Operating on the AV receiver 1 Press TONE repeatedly to select either “Bass” or “Treble”. 2 Use + and – to adjust. Note • To bypass the bass and treble tone circuits, select the Direct, Pure Audio or THX listening mode.
Audyssey Music Optimizer ■ Audyssey See “Audyssey” in “Source Setup” (➔ page 51). ■ Music Optimizer `Off `On Turn this setting on to enhance the sound quality of compressed music files. Use it with music files that use “lossy” compression, such as MP3. ■ Dynamic EQ See “Dynamic EQ” in “Source Setup” (➔ page 51). ■ Dynamic Volume See “Dynamic Volume” in “Source Setup” (➔ page 52).
Zone 2 In addition to the main listening room, you can also enjoy playback in another room, which we call Zone 2. For either of the rooms, you can specify a different input source. Connecting the Zone Speakers to an Additional Amplifier Making Zone 2 Connections There are two ways you can connect Zone 2 speakers: 1. Connect them directly to the AV receiver. 2. Connect them to an amp in Zone 2. Connecting Your Zone 2 Speakers Directly to the AV receiver This setup allows 7.
Controlling Zone 2 Components ■ Operating on the AV receiver Input selector buttons ZONE 2 OFF MASTER VOLUME Adjusting the Volume for Zone 2 ■ Operating on the remote controller 1 2 Press ZONE2. Use VOL q/w to adjust the volume. ■ Operating on the AV receiver 1 To turn on Zone 2 and select an input source, press ZONE 2 followed by an input selector button within 8 seconds. Zone 2 turns on, the Z2 indicator lights on the display. To select AM or FM, press the TUNER input selector button repeatedly.
Controlling Other Components iPod/iPhone Playback via Onkyo Dock Using the Onkyo Dock The Dock is sold separately. Models sold are different depending on the region. For the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod/iPhone with the latest software, available from the Apple web site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock.
■ Status Messages If either of the following messages is not displayed on the AV receiver’s display, check the connection to your iPod/iPhone. • PORT Reading The AV receiver is checking the connection with the dock. • PORT Not Support The AV receiver do not support the connected dock. • PORT UP-A1 UP-A1 Dock is connected. Note • The AV receiver displays the message “UP-A1” for several seconds after recognizing the UP-A1.
✔: Available buttons Press the appropriate REMOTE MODE first. Buttons ✔ a 8SOURCE*1 b TOP ✔*3 ✔ ✔*4 ✔ d 1, 3, 2, 5, 4, 7, 6 ✔ ✔ e REPEAT RANDOM ✔ ✔ ✔ ✔ f DISPLAY g MUTING ✔*5 ✔*6 ✔ ✔ h ALBUM +/– ✔*4 ✔ i VOL q/w ✔ ✔ j MENU k RETURN ✔ l MODE ✔*7 PLAYLIST e/r i b j c k ✔ MENU*2 c q/w/e/r, ENTER g h u Dock f UP-A1 Dock a Onkyo Dock ✔ ✔*8 d e l • With some iPod/iPhone models, generations and RI Docks, certain buttons may not work as expected.
Controlling Other Components You can use the AV receiver’s remote controller to control your other AV components, including those made by other manufacturers. This section explains how to enter the remote control code for a component that you want to control: DVD, TV, CD, etc. “Learning Commands” for learning commands directly from another component’s remote controller (➔ page 70). “Using Normal Macros” for programing ACTIVITIES to perform a sequence of remote control actions (➔ page 71).
Remote Control Codes for Onkyo Components Connected via u 2 Onkyo components that are connected via u are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example. 1 2 3 Make sure the Onkyo component is connected with an u cable and an analog audio cable (RCA). See “Connecting Onkyo u Components” for details (➔ page 20).
✔: Available buttons Press the appropriate REMOTE MODE first.
Learning Commands Note The AV receiver’s remote controller can learn the commands of other remote controllers. By transmitting, for example, the Play command from your CD player’s remote controller, the supplied remote controller can learn it, and then reproduce the exact same command when its 1 is pressed in CD remote mode. This is useful when you’ve entered the appropriate remote control code (➔ page 67) but some buttons don’t work as expected.
Running Macros Using Normal Macros You can program the remote controller’s ACTIVITIES to perform a sequence of remote control actions. Example: To play a CD you typically need to perform the following actions: 1. Press RECEIVER to select the Receiver remote controller mode. 2. Press 8RECEIVER to turn on the AV receiver. 3. Press TV/CD to select the TV/CD input source. 4. Press 1 to start playback on the CD player. You can program ACTIVITIES so that all four actions are performed with just one button press.
Appendix Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact your Onkyo dealer. If you can’t resolve the issue yourself, try resetting the AV receiver before contacting your Onkyo dealer. To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press 8ON/STANDBY. “Clear” will appear on the display and the AV receiver will enter standby mode.
■ Only the front speakers produce sound When the Stereo or Mono listening mode is selected, — only the front speakers and subwoofer produce sound. In the Mono listening mode, only the front speakers 49 output sound if the “Output Speaker” setting is set to “Left / Right”. Check the Speaker Configuration. 46 ■ Only the center speaker produces sound In the Mono listening mode, only the center speaker 49 output sound if the “Output Speaker” setting is set to “Center”.
■ The beginning of audio received by an HDMI IN can’t be heard Since it takes longer to identify the format of an HDMI signal than it does for other digital audio signals, audio output may not start immediately. — Video ■ There’s no picture Make sure that all video connecting plugs are pushed 16 in all the way. Relocate your antenna. — Move the AV receiver away from your TV or computer. — Listen to the station in mono.
To control an Onkyo component that’s not 68 connected via u, point the remote controller at the component. Be sure to enter the appropriate remote control code first. The entered remote control code may not be correct. — If more than one code is listed, try each one. ■ Can’t learn commands from another remote controller When learning commands, make sure that the transmitting ends of both remote controllers are pointing at each other.
■ Can’t connect to the AV receiver from a Web browser If you’re using DHCP, your router may not always 59 allocate the same IP address to the AV receiver, so if you find that you can’t connect to a server or Internet radio station, recheck the AV receiver’s IP address on the “Network” screen. Check the “Network” settings. 59 USB Device Playback ■ Can’t access the music files on a USB device Make sure the USB device is plugged in properly.
■ If the picture on your TV/monitor connected to HDMI OUT is unstable, try switching the DeepColor function off To turn off the DeepColor function, simultaneously press the CBL/SAT and 8ON/STANDBY buttons on the AV receiver. While holding down CBL/SAT, press 8ON/STANDBY until “Off” appears on the display. Then, release both buttons. To reactivate the DeepColor function, repeat the above process until “On” appears on the display and release the buttons.
Firmware Update To update the firmware of the AV receiver, you can choose from the following two methods: update via network, or update via USB storage. Choose the one that best suits your environment. Before proceeding with the update, please read the corresponding explanations carefully. ■ Update via network You need a wired Internet connection to update the firmware. ■ Update via USB storage (➔ page 79) Please prepare a USB storage device such as a USB flash memory stick.
7 Using 8ON/STANDBY on the front panel, turn off and on the AV receiver. Do not use 8RECEIVER on the remote controller. Congratulations! You now have the latest firmware installed on your Onkyo AV receiver. Troubleshooting Case 1: If “No Update” is displayed on the front display of the AV receiver, it means that the firmware has already been updated. You do not need to do anything further. Case 2: If an error occurs, “Error!! *-** No media” is displayed on the front display of the AV receiver.
8 9 10 11 12 13 Select “Hardware Setup” and press ENTER. Select “Firmware Update” and press ENTER. Select “via USB” and press ENTER. Select “Update” and press ENTER. The update process will begin. During the update process, the on-screen display may disappear depending on the updated program. When this occurs, you can still view the update progress on the front display of the AV receiver. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again.
Connection Tips and Video Signal Path The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your components. Use the following sections as a guide. The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.
Audio Connection Formats Audio components can be connected by using any of the following audio connection formats: analog, analog multichannel, optical, coaxial or HDMI. When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa. For example, audio signals connected to an optical or coaxial digital input are not output by the analog VCR/DVR OUT. Audio Signal Flow Chart Blu-ray Disc/DVD player, etc.
Video Resolution Chart The following tables show how video signals at different resolutions are output by the AV receiver.
Using an RIHD-compatible TV, Player, or Recorder p, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than p-compatible components cannot be guaranteed.
■ How to connect and setup 1 3 Confirm the connecting and setting. 1. Connect the HDMI OUT jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note • When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary (➔ page 58).
About HDMI Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.
Network/USB Features Connecting to the Network Network Requirements The following diagram shows how you can connect the AV receiver to your home network. In this example, it’s connected to a LAN port on a router, which has a 4-port 100Base-TX switch built-in. Internet radio Modem WAN LAN Computer or media server Router ■ Ethernet Network For the best results, a 100Base-TX switched Ethernet network is recommended.
Server Requirements ■ Server playback The AV receiver can play digital music files stored on a computer or media server and supports the following technologies: • Windows Media Player 11 • Windows Media Player 12 • Windows Media Connect 2.0 • DLNA-certified media server If the operating system of your computer is Windows Vista, Windows Media Player 11 is already installed. Windows Media Player 11 for Windows XP can be downloaded for free from the Microsoft web site.
Supported Audio File Formats For server playback and playback from a USB device, the AV receiver supports the following music file formats. Variable bit-rate (VBR) files are supported. However, playback time may not be display correctly. ■ LPCM (Linear PCM) • Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, and 96 kHz are supported. • Quantization bit: 8 bit, 16 bit, 24 bit * Only for playback via network.
Specifications Amplifier Section Tuner Section Rated Output Power All channels: FM Tuning Frequency Range (North American) 87.5 MHz - 107.9 MHz (Chinese) 87.5 MHz - 108.0 MHz, RDS AM Tuning Frequency Range 522/530 kHz - 1611/1710 kHz Preset Channel 40 (North American) 100 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.
■ Audio Outputs Analog VCR/DVR, ZONE2 LINE OUT Analog Multichannel Pre Outputs 7 Subwoofer Pre Outputs 2 Speaker Outputs Main (L, R, C, SL, SR, SBL, SBR) + Front Wide/ZONE2 (L, R) + Front High (L, R) Phones 1 (6.3 ø) ■ Others Setup Mic Universal Port RI USB Ethernet 1 1 1 1 (Front) 1 Specifications and features are subject to change without notice.
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 http://www.onkyo.com/ 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/ Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.
